斑马打印机的传感器(Zebraprintersensor)-USB迷|专注于互联网分享

2023年12月15日发(作者：泉英奕)

斑马打印机的传感器（Zebra printer sensor）

Zebra printer sensor

The printer's sensor has

Paper feed sensor, paper out sensor,

The inkjet printer has a car position sensor, and the upper part

of the cleaning unit is provided with a cart back position

Sensor,

In addition, there are laser scanners. These are relatively

simple.

Something more about the zebra printer. I hope you can use it

Zebra label printers use the whole process:

1. ribbon and label installation

According to the drawing direction, the dotted line is the

ribbon installation path, are for the label path. Rewind ribbon

easily peeled off after the waste, with waste label smooth

bottom roll in the scroll in the back into the front, and then

the ribbon. When installing the label, adjust the paper holder

according to the label width. The pressure head spring is

uniform and can avoid the deviation of the printer label. The

first time you use a printer, you need to carry out measuring

paper.

2. panel control

PAUSE key: pause and start printing FEED key: take a piece of

paper CANCEL key: when the print data is transferred to the

printer, but without printing, you can press PAUSE first, and

then press CANCEL several times until the data light is closed.

CALIBRATE: tag test. When you install the new specification

label, you can print the parameters of the tag before you print

it properly. Method: press the PAUSE key first, then press

CALIBRATE to do the measuring paper. When the paper is checked,

the label has an acceleration process, indicating that the

paper is correct. Note: the test paper can rewind finished label,

ribbon cannot rewind.

3. equipment debugging

Customers can choose according to their own requirements to

print SETUP into the set temperature value Tear - Darkness off

- Print mode ----------PEEL label from OFF (tearing way) -

--------NON-CONTINOUS Media type Print Method (discontinuous

paper) --------THERMAL TRANS (thermal transfer) Print Width -

List Formats - print width format list List Setup - set Media

and Ribbon Calibrate - list of test paper and ribbon Label Top

- Left Position adjust the position of the top label printing,

print position adjust tab on the left around with black button

to modify the settings, select the EXIT button to exit. Finally,

select the NEXT/SAVE key to save the settings data. In the

normal debugging, can enter the set LIST SETUP, and then choose

the right black button to print standard settings, save the

labels for failure checking.

4. regular maintenance

The printer keeps the print head clean during use, so as to

guarantee the printing quality and prolong the life of the print

head. Clean the print head, rubber roller, ribbon sensor with

alcohol on each print roll label. When replacing a printed cable,

first turn off the printer, the computer power, and then connect

the cable. Note: when cleaning and printing the first class,

you should turn off the power supply. The print head belongs

to the precision parts. It is better to ask the professionals

to clean it!

5. print head pressure regulation

Press the print head pressure according to the print medium.

The print head under the condition of normal pressure adjusting

nut to the highest position to print the best results when

compared with the long-term. Otherwise there will be printing

rollers deformation, resulting in ribbon wrinkles, poor

printing effect.

6. printer all the indicator light, LCD does not display and

can not operate

Reason: motherboard or EPROM damage solution: contact your

distributor, replace the motherboard, or install the EPROM

correctly

7. the printer blinks all the indicators and does not measure

the paper

Reason: sensor fault solution: clean sensor surface dust or

contact your distributor to replace sensors

8. printer printing process longitudinal missing line

Reason: the surface of the print head is sticky with dust or

the printer wears out for long periods of time. The solution

is to clean the print head or replace the print head with alcohol

Ribbon or paper label printer in deviation 9.

Reason: uneven paper spring and paper gauge not adjusted by

width: solution of spring and paper limiting device

10. printing is not clear, poor quality

1 reasons: the temperature is too low 2 ribbon label poor

quality 3 print head is not correctly installed solution: 1

increase the printing temperature increase printing density 2

replacement ribbon and label paper 3 to re adjust the print head

position, with particular attention to the highly consistent

11. ribbon wrinkled

Reason: 1 no right around the ribbon machine 2 temperature

setting incorrect pressure and balance set 3 of the print head

is not correct 4 medium not correctly set paper quantity

solution: 1 re installed correctly adjust the print medium 2

temperature, as far as possible to meet the requirements of

printing 3 re set the print required minimum pressure 4 reset

medium the correct amount of paper

12. change parameter setting has no effect

The reasons may be: parameter setting is not correct, if the

parameter settings are correct and the problem still exists,

the problem may be the motherboard solution: reboot the factory

settings, and then set the parameters, and permanent storage.

If a reboot, the factory set, according to the default method

using the printer, or if not, only to replace the motherboard

manufacturers.

13. use BarOne software to print Chinese characters, English

and barcode, and print with other printing software

Reason: BarOne software controls printers directly, while many

other print software prints through windows drivers. Only by

selecting the right printer to print Chinese characters, new

drivers are recommended. Solution: contact your product vendor

or use BarOne and other software that drives the printer

directly.

14. I used to print the label is normal, but, since the change

of another ribbon, label printing, paper is not always normal

The reason is: the printer ribbon identification sensor and

label with memory. When the transfer paper and ribbon needed

from the new test paper. Solution: in the case of S400, in the

normal print mode, press the MODE button three times, press the

FEED key, then a lot of paper, paper paper paper is completed,

information is automatically recorded in the printer, the next

boot from the new test without paper. Run out of paper from the

new rollback.

15. printing small labels is normal, but printing large labels

always hit half, and the other half is empty

Reason: there is too little print memory and partial loss of

information when the tag is too large: contact your product

vendor and increase printer memory.

16. I should use what kind of bar code printer

Zebra printers are divided into three series: S series,

22. I have a zebra 105se printer on my side. At the beginning

of the printing, I always put the label roll into the scroll

shaft. What's the solution?

There may be two reasons: 1, the label paper you bought is too

thin, especially the bottom adhesive is very strong,.2, too

much pressure on the print head. Solution: 1, buy.2 series label

paper Boyu, small print head pressure

23. excuse me, what kind of equipment does the printer check

label paper have? What's wrong with label paper in general?

The printer's paper detector is a sensor. The possible problems

are: 1. The penetrating sensor of the label is hidden and

blocked. 2, the paper is not correct. 3, the printer is

incorrectly set (XII series). 4, the sensor position is wrong.

5, printer motherboard and sensor issues.

24., our company has a S600 zebra machine, printing ribbons

often wrinkled, resulting in printing quality degradation,

what is the solution?

Probably there are five: 1, the ribbon width to the label as

3cm. 2, the ribbon guide shaft or the guide shaft surface dirty,

toner adhesion. 3, the print head pressure bar around the uneven

pressure. 4, with poor quality, the surface is not smooth. 5,

astringent, and ribbon labels are not matching.

25. did not go when printing ribbon, and label paper walk, walk

a ribbon and after continue. But this phenomenon is appeared

in the print job, is generally in the thousands of photos, this

situation is not stable, sometimes, sometimes not,

There are many gear locating sensors in the large printer