2024年1月13日发(作者：长孙英秀)

1.1.1 Rear Cam mipi 布线串联共模电感1.1.2 Rear cam csi 1 主摄接线1.1.3 Rear cam rst 脚1.1.4 Rear cam mclk 时钟脚1.1.5 Rear cam pwn 脚

&i2c0 { // 根据camera挂载更改 status = "okay"; clock-frequency = <400000>; /* Rear Camera */ sensor_main: sensor-main@37 { compatible = "sprd,sensor-main"; reg = <0x37>; clock-names = "clk_src","sensor_eb", "clk_96m","clk_76m8", "clk_48m","clk_26m"; clocks = <&clk_sensor1>, <&clk_mm_ckg_gates 2>, <&clk_twpll_96m>,<&clk_twpll_76m8>, <&clk_twpll_48m>,<&ext_26m>; vddio-supply = <&vddcamio>; vddcama-supply = <&vddcama>; vddcamd-supply = <&vddcamd>; vddcammot-supply = <&vddcammot>; reset-gpios = <&ap_gpio 45 0>; power-down-gpios = <&ap_gpio 47 0>; host = "dcam0"; port { sensor_main_0: endpoint { remote-endpoint = <&phy1_out>; }; }; };...};1.2.2 Rear cam mipi 节点配置&mipi_csi_phy1 { status = "okay"; sprd,phyid = <1>; sprd,csi = <&csi0>; port { phy1_out: endpoint { remote-endpoint = <&sensor_main_0>; }; };};1.3 前摄硬件原理图 (Front Camera SCH)前摄 sp0a09z 03M(30w)像素

1.3.1 Front cam mipi 布线串联共模电感

1.3.2 Front cam csi 0 前摄接线1.3.3 Front cam rst 脚1.3.4 Front cam mclk 脚1.3.5 Front cam pwn 脚1.3.6 Front cam 获取前摄信息

1. MIPI – CSI0 接线1. MCSI0_CLK_P,MCSI0_CLK_N2. MCSI0_DATA0_P,MCSI1_DATA0_N2. cam rst复位脚、 cam mclk 时钟脚、csm pwn 脚

2024年1月13日发(作者：长孙英秀)

1.1.1 Rear Cam mipi 布线串联共模电感1.1.2 Rear cam csi 1 主摄接线1.1.3 Rear cam rst 脚1.1.4 Rear cam mclk 时钟脚1.1.5 Rear cam pwn 脚

&i2c0 { // 根据camera挂载更改 status = "okay"; clock-frequency = <400000>; /* Rear Camera */ sensor_main: sensor-main@37 { compatible = "sprd,sensor-main"; reg = <0x37>; clock-names = "clk_src","sensor_eb", "clk_96m","clk_76m8", "clk_48m","clk_26m"; clocks = <&clk_sensor1>, <&clk_mm_ckg_gates 2>, <&clk_twpll_96m>,<&clk_twpll_76m8>, <&clk_twpll_48m>,<&ext_26m>; vddio-supply = <&vddcamio>; vddcama-supply = <&vddcama>; vddcamd-supply = <&vddcamd>; vddcammot-supply = <&vddcammot>; reset-gpios = <&ap_gpio 45 0>; power-down-gpios = <&ap_gpio 47 0>; host = "dcam0"; port { sensor_main_0: endpoint { remote-endpoint = <&phy1_out>; }; }; };...};1.2.2 Rear cam mipi 节点配置&mipi_csi_phy1 { status = "okay"; sprd,phyid = <1>; sprd,csi = <&csi0>; port { phy1_out: endpoint { remote-endpoint = <&sensor_main_0>; }; };};1.3 前摄硬件原理图 (Front Camera SCH)前摄 sp0a09z 03M(30w)像素

1.3.1 Front cam mipi 布线串联共模电感

1.3.2 Front cam csi 0 前摄接线1.3.3 Front cam rst 脚1.3.4 Front cam mclk 脚1.3.5 Front cam pwn 脚1.3.6 Front cam 获取前摄信息

1. MIPI – CSI0 接线1. MCSI0_CLK_P,MCSI0_CLK_N2. MCSI0_DATA0_P,MCSI1_DATA0_N2. cam rst复位脚、 cam mclk 时钟脚、csm pwn 脚