易微联MINI Extreme Wi-Fi智能开关说明书-USB迷|专注于互联网分享

2024年2月21日发(作者：声青)

MINI ExtremeWi-Fi Smart Switch·中文 ----------1 - 7· English ----------8 - 14· Warning ----------15 - 16

产品介绍按键网络指示灯接线端口设备重量＜1Kg，建议安装高度＜2米。信号指示灯状态说明蓝灯呈两短一长闪烁蓝色常亮指示灯状态状态说明蓝牙配网模式设备在线1

功能特点MINI Extreme紧凑小巧的机身，能够安装在开关暗盒中且最大支持10A负载，使普通开关变为智能开关。安全且智能，也可在智能场景中联动其他设备，实现你的家庭自动化。

远程控制智能定时/延时语音控制局域网控制通电反应点动模式智能场景群组控制设备安装1. 断电设备安装、故障维修请由专业资质电工操作。切勿在设备通电时进行接线操作或触碰到接线端子，以免发生触电危险！2

2. 接线1. S1、S2 接或不接开关，设备都可通过自动化或App来控制。造成危险。3. 确保线路接入无误。2. 禁止将S1连接零线、地线等强电, 禁止将S2连接火线、零线、地线等强电，以免损坏设备，配对至易微联App1. 下载易微联App请前往应用商店、Google Play Store或Apple App Store搜索"易微联"进行下载。3

2. 上电通电后，设备首次使用，默认进入蓝牙配网模式。网络指示灯呈“两短一长闪烁”。10分钟内没有进行配网，设备将退出蓝牙配网模式。如需再次进入，长按设备按钮5秒直到网络指示灯呈两短一长闪烁即可。3.添加设备点击“+”，选择“蓝牙配网”，再根据 App 提示进行操作。蓝牙配网4

添加轻智能子设备加成功。进入 eWeLink App 设备设置页面，选择“轻智能子设备”再点击“添加”，然后触发子设备，即可添添加轻智能子设备0/8将MINI Extreme安装在暗盒中5

产品参数产品型号输入输出MINIR4100-240V ~ 50/60Hz 10A Max100-240V ~ 50/60Hz 10A Max2400WIEEE 802.11b/g/n 2.4GHz-10℃-40℃PC V05%-95%RH,无冷凝39.5x33x16.8mm最大功率Wi-Fi工作温度工作湿度外壳材料产品规格更换设备网络在 eWeLink App 设备设置界面选择 “WiFi设置” 进行更换。恢复出厂设置常见问题在 eWeLink App 端“删除设备”，设备即恢复出厂设置。1. Wi-Fi设备与易微联App配对失败1、确保设备进入配对模式.10分钟内设备没有配对成功，则自动退出配对模式。2、请开启定位服务以及允许获取定位权限配网前，请先开启手机的定位服务并允许获取定位权限。位置信息权限用于获取Wi-Fi列表信息，如果“禁用”手机定位服务，设备将无法添加。6

3、确保Wi-Fi运行在2.4GHz频段。4、确保正确输入Wi-Fi网络名称和密码，且没有包含特殊字符。

密码错误是常见的配对失败原因。5、配对时为了确保良好的信号传输，请将设备靠近路由器。2. LED指示灯连续闪烁两次，服务器连接失败1、确保网络连接正常。你可以通过手机或者电脑连接网络。如果连接失败，请检查网络。2、路由器承载力较低，连接到路由器的设备超过最大值。请查看你的路由器可以连接的最大设备数量。如果超过最大值，请删除个别设备或者更换一个承载力较高的路由器再次连接。如果以上方法均无法解决此问题，请在易微联APP上通过“帮助&反馈”提交你的问题。3. Wi-Fi设备“离线”问题

1、路由器连接失败2、输入不正确的Wi-Fi网络名称和密码导致Wi-Fi连接失败3、 Wi-Fi网络名称和密码包含特殊字符。例如，我们的系统无法识别希伯来语和阿拉伯语字符，4、路由器承载力较低输。5、 Wi-Fi信号太弱。路由器和设备间隔太远，或者路由器与设备之前有障碍物导致信号无法传7

EnglishProduct introductionButtonNetwork indicatorWiring portsThe device weight is less than 1kg, and the recommended installation height is less

than ction of LED indicator status

LED indicator statusBlue LED indicator ﬂashes(one long and two short)Blue LED indicator keeps on

Status instructionBluetooth pairing modeDevice is online8

EnglishFeaturesMINI Extreme is compact and tiny enough to be installed in the mounted box, and it

supports loads of up to 10A, enable to transform your ordinary switch into a smart switch.

Safe and smart, allows you to set smart scenes with other smart devices to automate your

ControlTimer ScheduleVoice ControlLAN ControlPower-on StateInching ModeSmart SceneGroup ControlInstallation1. Power oﬀPlease install and maintain the device by a professional electrician. To avoid electric

shock hazard, do not operate any connection or contact the terminal connector while

the device is powered on!9

English2. Wiring instructionBefore installing the device, please install an air switch as the protective device(Air switch: 10A/250V).1、No matter S1 and S2 are connected or left idle to the external switch, this device

canbe controlled by automation or the App.2、To avoid damaging the equipment and causing danger, it is forbidden to connect

S1 to strong electricity such as neutral wire or earth wire or to connect S2 to strong

electricity such as live wire, neutral wire, earth wire and etc.3、Make sure all wires are connected with eWeLink App1. Download the eWeLink AppPlease download the "eWeLink" App from Google Play Store or Apple App Store.10

English2. Power onAfter powering on, the device will enter the Bluetooth Pairing Mode defaulted during

the ﬁrst use, and the Network indicator ﬂashes in a cycle of two short and one device will exit the Bluetooth Pairing Mode if not been paired within 10mins. If

you want to enter this mode again, please long press the button for 5s until the

Network indicator ﬂashes in a cycle of two short and one long and then deviceTap “+” and select “Bluetooth Pairing”, then operate following the prompt on the App.11

EnglishAdd eWeLink-Remote Sub-devicesEnter the Device Settings page on the eWeLink App, select "eWeLink-Remote sub-devices"

and tap "Add", then trigger the sub-device to add it l the MINI Extreme in the mounting box12

EnglishSpeciﬁcationsModelInputOutputMax. powerWi-FiWorking temperatureWorking humidityCasing materialDimensionMINIR4100-240V ~ 50/60Hz 10A Max100-240V ~ 50/60Hz 10A Max2400WIEEE 802.11b/g/n 2.4GHz-10℃-40℃5%-95% RH, non-condensingPC V039.5x33x16.8mmDevice Network ChangingChange the device's network by "Wi-Fi Settings" in the "Device Settings" page on the

eWeLink App.

Factory ResetReset the device to factory settings by "Delete device" on the eWeLink (Frequently Asked Questions)1. Fail to pair Wi-Fi devices with the eWeLink App1、Make sure the device is in pairing device will automatically exit the pairing mode if it is not paired within 10mins.

2、Please enable location service and allow access to location connecting Wi-Fi network, please enable the location service and allow access

to the location permission. Location information permission is used to obtain Wi-Fi listinformation, if you "disable" the location service, the device cannot be paired.13

English3、Make sure your Wi-Fi works on 2.4GHz band.

4、Make sure to enter the Wi-Fi SSID and password correctly without special ect password is a common cause of pairing router.5、To ensure good signal transmission while pairing, please place the device close to

2. The LED indicator ﬂashes twice on repeated means the server

fails to phone or PC. If fail to connect, please check the availability of the Internet

connection.1、Make sure the networking is normal. Check the internet works well by connecting

2.、With the low load capacity of the router, the connected devices exceed the router's

maximum load capacity. Please check the maximum number of devices that your

devices or use a higher load capacity can carry, if the connected devices exceed the maximum value, remove some

If the above methods cannot help to solve the problem, please submit your problem

to "Help & Feedback" on the eWeLink App.3. Wi-Fi devices are "oﬄine"

1、Devices fail to connect to the router.2、Entered the wrong Wi-Fi SSID and password.3、Wi-Fi SSID and password contain special characters, for example, our system can't

recognize Hebrew and Arabic characters, which causes Wi-Fi connections to fail.4、Low capacity of the router.5、Wi-Fi signal is weak. The router and the devices are too far apart, or there is an

le between the router and the device, which prevents the signal from being

WarningFCC WarningChanges or modiﬁcations not expressly approved by the party responsible for compliance

could avoid the user’s authority to operate the device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with

any other antenna or :This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment oﬀ and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit diﬀerent from that to which the

receiver is connected.— Consult the dealer or an experienced radio/TV technician for help.

WarningIC WarningThis device complies with Innovation, Science and Economic Development Canada

licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1)

this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the onjunc areil est conforme aux CNR d’ l’innovation, la science et le développement

économique Canada licables aux areils radio exempts de licence.L’exploitation est autorisée aux deux conditions suivantes:(1) l’areil ne doit pas produire de brouillage, et(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, onj si le

brouillage est susceptible d’en compromettre le changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the les changements ou modiﬁcations non expressément approuvée par le responsible

de la conformité pourrait vider l’utilisateur est habilité à exploiter l’é Radiation Exposure Statement:This equipment complies with ISEDC RF radiation exposure limits set forth for an

uncontrolled transmitter must not be co-located or operating in conjunction with any other

antenna or appareil estconforme aux limitesd’exposition de rayonnement RF ISEDC établiespour un environne-ment non contrôlé.Cetémetteur ne doit pas être co-implanté oufonctionner en onjunction avec toute

autreantenne ou transmetteur.16

Hereby, Shenzhen Sonoﬀ Technologies Co., Ltd. declares that the radio equipment type

MINIR4 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet address:sonoﬀ.tech/usermanualsOperation frequency Range:2402-2480MHz(BLE)2412-2472MHz(Wi-Fi)RF Output Power:2dBm(BLE)15dBm(802.11b),14dBm(802.11g),15dBm(802.11n20),16dBm(802.11n40)(Wi-Fi)