2024年3月29日发(作者：禄逸馨)
FLECK 5600 WATER SOFTENER INSTALLATION
Discount Water Softeners recommends using a licensed plumber to install your
water softener. The following installation instructions are for use with the water
softener system you now own. Discount Water Softeners assumes no responsibility
for improper installation or injury.
Additional instructions are also in your water softener manufacturers’ manual on
page 3. Skip steps 3 and 4 in the mfg. manual. For SE model use the pink pullout
that came with the manufacturers manual for the 5600SE programming guide.
Step 1:
Location of your softener is important. It should be in a protected dry, level and
non-freezing area (34-120 degrees F). The 2 tanks should be set close to each other.
The square tank is your salt (brine) tank (for softener salt or potassium chloride)
and it is the tank that you will have to refill with salt from time to time, so make it
the more accessible of the 2 tanks. Do not put salt in this tank until you have put the
softener into service and have tested the cycles.
Step 2:
You will need a standard outlet that is not controlled by a switch. You should also
have a floor drain located nearby.
Step 3:
The distributor tube or turbulator should be placed in the softener tank with the
distributor basket end down. The softener tank (fiberglass construction) is the taller
of the two tanks and shown in the following picture. Turn the tube a couple times to
make sure that the bottom basket seats properly in the bottom of the tank. Make
sure the distributor tube or turbulator is in the tank BEFORE YOU ADD THE
RESIN!
Step 4:
Be sure to place the softener tank shown above where you want to connect it to your
water line because it will be heavy a difficult to move after the resin is added. Make
sure you install your softener in line before your hot water heater to insure that you
have full benefit of the softener system.
Step 5:
Be sure to cover the open upper end of the distributor tube or turbulator with tape
or the cap as shown below to keep any resin from falling into the distributor tube or
turbulator tube while pouring the resin into the softener tank. Remove the tape
after filling the tank with resin.
2024年3月29日发(作者：禄逸馨)
FLECK 5600 WATER SOFTENER INSTALLATION
Discount Water Softeners recommends using a licensed plumber to install your
water softener. The following installation instructions are for use with the water
softener system you now own. Discount Water Softeners assumes no responsibility
for improper installation or injury.
Additional instructions are also in your water softener manufacturers’ manual on
page 3. Skip steps 3 and 4 in the mfg. manual. For SE model use the pink pullout
that came with the manufacturers manual for the 5600SE programming guide.
Step 1:
Location of your softener is important. It should be in a protected dry, level and
non-freezing area (34-120 degrees F). The 2 tanks should be set close to each other.
The square tank is your salt (brine) tank (for softener salt or potassium chloride)
and it is the tank that you will have to refill with salt from time to time, so make it
the more accessible of the 2 tanks. Do not put salt in this tank until you have put the
softener into service and have tested the cycles.
Step 2:
You will need a standard outlet that is not controlled by a switch. You should also
have a floor drain located nearby.
Step 3:
The distributor tube or turbulator should be placed in the softener tank with the
distributor basket end down. The softener tank (fiberglass construction) is the taller
of the two tanks and shown in the following picture. Turn the tube a couple times to
make sure that the bottom basket seats properly in the bottom of the tank. Make
sure the distributor tube or turbulator is in the tank BEFORE YOU ADD THE
RESIN!
Step 4:
Be sure to place the softener tank shown above where you want to connect it to your
water line because it will be heavy a difficult to move after the resin is added. Make
sure you install your softener in line before your hot water heater to insure that you
have full benefit of the softener system.
Step 5:
Be sure to cover the open upper end of the distributor tube or turbulator with tape
or the cap as shown below to keep any resin from falling into the distributor tube or
turbulator tube while pouring the resin into the softener tank. Remove the tape
after filling the tank with resin.