2024年4月6日发(作者：赫灵珊)
-!
基于enspv510版ac与ap配置
四川托普信息职业技术学院 唐小军
一、 拓扑图
二、 实验环境：
三、 相应设备：
1.无线AP:5030, AC:6605,
-!
2.交换：二层，s3700，三层，s5700
3.电脑：STA
四、 实现目标：
1． STA3能通过无线方式访问到三层交换机接口地址，10.23.101.2
五、 配置思路
1.配置AP、AC和周边网络设备之间实现网络互通。
2.配置AP上线。
a) 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
b) 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
c) 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
3.配置WLAN业务参数，实现STA访问WLAN网络功能。
六、 实验过程：
1. 二层交换机配置
-!
[HUAWEI] sysname Switch
[Switch] vlan batch 100 101
[Switch] interface Ethernet0/0/1
[Switch-Ethernet0/0/1] port link-type trunk
[Switch-Ethernet0/0/1] port trunk pvid vlan 100
[Switch-Ethernet0/0/1] port trunk allow-pass vlan 100 101
[Switch-Ethernet0/0/1] port-isolate enable
[Switch-Ethernet0/0/1] quit
[Switch] interface gigabitethernet 0/0/2
[Switch-Ethernet0/0/2] port link-type trunk
[Switch-Ethernet0/0/2] port trunk allow-pass vlan 100 101
[Switch-Ethernet0/0/2] quit
-!
2. 三层交换机配置
[Huawei] sysname Router
[Router] vlan batch 101
[Router] interface gigabitethernet 0/0/1
[Router-GigabitEthernet0/0/1] port link-type trunk
[Router-GigabitEthernet0/0/1] port trunk allow-pass vlan 101
[Router-GigabitEthernet0/0/1] quit
[Router] interface vlanif 101
[Router-Vlanif101] ip address 10.23.101.2 24
[Router-Vlanif101] quit
3. 配置AC与其它网络设备互通
-!
[AC6605] sysname AC
[AC] vlan batch 100 101
[AC] interface gigabitethernet 0/0/1
[AC-GigabitEthernet0/0/1] port link-type trunk
[AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100 101
[AC-GigabitEthernet0/0/1] quit
[AC] interface gigabitethernet 0/0/2
[AC-GigabitEthernet0/0/2] port link-type trunk
[AC-GigabitEthernet0/0/2] port trunk allow-pass vlan 101
[AC-GigabitEthernet0/0/2] quit
4. 在AC上配置DHCP服务器为STA和AP分配IP地址
[AC] dhcp enable
[AC] interface vlanif 100
-!
[AC-Vlanif100] ip address 10.23.100.1 24
[AC-Vlanif100] dhcp select interface
[AC-Vlanif100] quit
[AC] interface vlanif 101
[AC-Vlanif101] ip address 10.23.101.1 24
[AC-Vlanif101] dhcp select interface
[AC-Vlanif101] quit
5. 在AC上配置AP上线
# 创建AP组，用于将相同配置的AP都加入同一AP组中。
[AC] wlan
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] quit
# 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。
-!
[AC-wlan-view] regulatory-domain-profile name default
[AC-wlan-regulate-domain-default] country-code cn
[AC-wlan-regulate-domain-default] quit
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] regulatory-domain-profile default
Warning: Modifying the country code will clear channel, power and antenna
gain configurations of the radio and reset the AP. Continu
e?[Y/N]:y
[AC-wlan-ap-group-ap-group1] quit
[AC-wlan-view] quit
# 配置AC的源接口。
[AC] capwap source interface vlanif 100
6. 查看ap的mac地址做好记录以备用，并为ap设置部署名称例如area_1
-!
7. AP具有射频0和射频1两个射频。例如AP5030DN的射频0为2.4GHz射频，射
频1为5GHz射频。
[AC] wlan
[AC-wlan-view] ap auth-mode mac-auth
[AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360
[AC-wlan-ap-0] ap-name area_1
[AC-wlan-ap-0] ap-group ap-group1
Warning: This operation may cause AP reset. If the country code changes, it
will clear channel, power and antenna gain configuration
-!
s of the radio, Whether to continue? [Y/N]:y
[AC-wlan-ap-0] quit
8. 保证AP上电并与AC连接，当执行命令display ap all查看到AP的“State”字
段为“nor”时，表示AP正常上线。
[AC-wlan-view] display ap all
Total AP information:
nor : normal [1]
-------------------------------------------------------------------------------------
ID MAC Name Group IP Type
State STA Uptime
-------------------------------------------------------------------------------------
0 00e0-fcfe-1e60 area_1 ap-group1 10.23.100.106 AP5030DN nor
0 10S
-------------------------------------------------------------------------------------
Total: 1
-!
9. 配置WLAN业务参数，配置WPA-WPA2+PSK+AES的安全策略，密码为
“a1234567”
[AC-wlan-view] security-profile name wlan-net
[AC-wlan-sec-prof-wlan-net] security wpa-wpa2 psk pass-phrase a1234567
aes
[AC-wlan-sec-prof-wlan-net] quit
# 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。
[AC-wlan-view] ssid-profile name wlan-net
[AC-wlan-ssid-prof-wlan-net] ssid wlan-net
[AC-wlan-ssid-prof-wlan-net] quit
# 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且
引用安全模板和SSID模板。
[AC-wlan-view] vap-profile name wlan-net
[AC-wlan-vap-prof-wlan-net] forward-mode direct-forward
[AC-wlan-vap-prof-wlan-net] service-vlan vlan-id 101
-!
[AC-wlan-vap-prof-wlan-net] security-profile wlan-net
[AC-wlan-vap-prof-wlan-net] ssid-profile wlan-net
[AC-wlan-vap-prof-wlan-net] quit
# 配置AP组引用VAP模板，AP上射频0和射频1都使用VAP模板“wlan-net”
的配置。
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 0
[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 1
[AC-wlan-ap-group-ap-group1] quit
10. 配置AP射频的信道和功率,关闭射频的信道和功率自动调优功能。射频的信道
和功率自动调优功能默认开启，如果不关闭此功能则会导致手动配置不生效。
[AC-wlan-view] rrm-profile name default
[AC-wlan-rrm-prof-default] calibrate auto-channel-select disable
[AC-wlan-rrm-prof-default] calibrate auto-txpower-select disable
-!
[AC-wlan-rrm-prof-default] quit
# 配置AP射频0的信道和功率。
[AC-wlan-view] ap-id 0
[AC-wlan-ap-0] radio 0
[AC-wlan-radio-0/0] channel 20mhz 6
Warning: This action may cause service interruption. Continue?[Y/N]y
[AC-wlan-radio-0/0] eirp 127
[AC-wlan-radio-0/0] quit
# 配置AP射频1的信道和功率。
[AC-wlan-ap-0] radio 1
[AC-wlan-radio-0/1] channel 20mhz 149
Warning: This action may cause service interruption. Continue?[Y/N]y
[AC-wlan-radio-0/1] eirp 127
-!
[AC-wlan-radio-0/1] quit
[AC-wlan-ap-0] quit
11. 验证配置结果, WLAN业务配置会自动下发给AP，配置完成后，通过执行命令
display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP
对应的射频上的VAP已创建成功。
12. STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联
后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线
网络“wlan-net”中。
在STA3上做如下操作：
-!
-!
-!
2024年4月6日发(作者：赫灵珊)
-!
基于enspv510版ac与ap配置
四川托普信息职业技术学院 唐小军
一、 拓扑图
二、 实验环境：
三、 相应设备：
1.无线AP:5030, AC:6605,
-!
2.交换：二层，s3700，三层，s5700
3.电脑：STA
四、 实现目标：
1． STA3能通过无线方式访问到三层交换机接口地址，10.23.101.2
五、 配置思路
1.配置AP、AC和周边网络设备之间实现网络互通。
2.配置AP上线。
a) 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
b) 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
c) 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
3.配置WLAN业务参数，实现STA访问WLAN网络功能。
六、 实验过程：
1. 二层交换机配置
-!
[HUAWEI] sysname Switch
[Switch] vlan batch 100 101
[Switch] interface Ethernet0/0/1
[Switch-Ethernet0/0/1] port link-type trunk
[Switch-Ethernet0/0/1] port trunk pvid vlan 100
[Switch-Ethernet0/0/1] port trunk allow-pass vlan 100 101
[Switch-Ethernet0/0/1] port-isolate enable
[Switch-Ethernet0/0/1] quit
[Switch] interface gigabitethernet 0/0/2
[Switch-Ethernet0/0/2] port link-type trunk
[Switch-Ethernet0/0/2] port trunk allow-pass vlan 100 101
[Switch-Ethernet0/0/2] quit
-!
2. 三层交换机配置
[Huawei] sysname Router
[Router] vlan batch 101
[Router] interface gigabitethernet 0/0/1
[Router-GigabitEthernet0/0/1] port link-type trunk
[Router-GigabitEthernet0/0/1] port trunk allow-pass vlan 101
[Router-GigabitEthernet0/0/1] quit
[Router] interface vlanif 101
[Router-Vlanif101] ip address 10.23.101.2 24
[Router-Vlanif101] quit
3. 配置AC与其它网络设备互通
-!
[AC6605] sysname AC
[AC] vlan batch 100 101
[AC] interface gigabitethernet 0/0/1
[AC-GigabitEthernet0/0/1] port link-type trunk
[AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100 101
[AC-GigabitEthernet0/0/1] quit
[AC] interface gigabitethernet 0/0/2
[AC-GigabitEthernet0/0/2] port link-type trunk
[AC-GigabitEthernet0/0/2] port trunk allow-pass vlan 101
[AC-GigabitEthernet0/0/2] quit
4. 在AC上配置DHCP服务器为STA和AP分配IP地址
[AC] dhcp enable
[AC] interface vlanif 100
-!
[AC-Vlanif100] ip address 10.23.100.1 24
[AC-Vlanif100] dhcp select interface
[AC-Vlanif100] quit
[AC] interface vlanif 101
[AC-Vlanif101] ip address 10.23.101.1 24
[AC-Vlanif101] dhcp select interface
[AC-Vlanif101] quit
5. 在AC上配置AP上线
# 创建AP组，用于将相同配置的AP都加入同一AP组中。
[AC] wlan
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] quit
# 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。
-!
[AC-wlan-view] regulatory-domain-profile name default
[AC-wlan-regulate-domain-default] country-code cn
[AC-wlan-regulate-domain-default] quit
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] regulatory-domain-profile default
Warning: Modifying the country code will clear channel, power and antenna
gain configurations of the radio and reset the AP. Continu
e?[Y/N]:y
[AC-wlan-ap-group-ap-group1] quit
[AC-wlan-view] quit
# 配置AC的源接口。
[AC] capwap source interface vlanif 100
6. 查看ap的mac地址做好记录以备用，并为ap设置部署名称例如area_1
-!
7. AP具有射频0和射频1两个射频。例如AP5030DN的射频0为2.4GHz射频，射
频1为5GHz射频。
[AC] wlan
[AC-wlan-view] ap auth-mode mac-auth
[AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360
[AC-wlan-ap-0] ap-name area_1
[AC-wlan-ap-0] ap-group ap-group1
Warning: This operation may cause AP reset. If the country code changes, it
will clear channel, power and antenna gain configuration
-!
s of the radio, Whether to continue? [Y/N]:y
[AC-wlan-ap-0] quit
8. 保证AP上电并与AC连接，当执行命令display ap all查看到AP的“State”字
段为“nor”时，表示AP正常上线。
[AC-wlan-view] display ap all
Total AP information:
nor : normal [1]
-------------------------------------------------------------------------------------
ID MAC Name Group IP Type
State STA Uptime
-------------------------------------------------------------------------------------
0 00e0-fcfe-1e60 area_1 ap-group1 10.23.100.106 AP5030DN nor
0 10S
-------------------------------------------------------------------------------------
Total: 1
-!
9. 配置WLAN业务参数，配置WPA-WPA2+PSK+AES的安全策略，密码为
“a1234567”
[AC-wlan-view] security-profile name wlan-net
[AC-wlan-sec-prof-wlan-net] security wpa-wpa2 psk pass-phrase a1234567
aes
[AC-wlan-sec-prof-wlan-net] quit
# 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。
[AC-wlan-view] ssid-profile name wlan-net
[AC-wlan-ssid-prof-wlan-net] ssid wlan-net
[AC-wlan-ssid-prof-wlan-net] quit
# 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且
引用安全模板和SSID模板。
[AC-wlan-view] vap-profile name wlan-net
[AC-wlan-vap-prof-wlan-net] forward-mode direct-forward
[AC-wlan-vap-prof-wlan-net] service-vlan vlan-id 101
-!
[AC-wlan-vap-prof-wlan-net] security-profile wlan-net
[AC-wlan-vap-prof-wlan-net] ssid-profile wlan-net
[AC-wlan-vap-prof-wlan-net] quit
# 配置AP组引用VAP模板，AP上射频0和射频1都使用VAP模板“wlan-net”
的配置。
[AC-wlan-view] ap-group name ap-group1
[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 0
[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 1
[AC-wlan-ap-group-ap-group1] quit
10. 配置AP射频的信道和功率,关闭射频的信道和功率自动调优功能。射频的信道
和功率自动调优功能默认开启，如果不关闭此功能则会导致手动配置不生效。
[AC-wlan-view] rrm-profile name default
[AC-wlan-rrm-prof-default] calibrate auto-channel-select disable
[AC-wlan-rrm-prof-default] calibrate auto-txpower-select disable
-!
[AC-wlan-rrm-prof-default] quit
# 配置AP射频0的信道和功率。
[AC-wlan-view] ap-id 0
[AC-wlan-ap-0] radio 0
[AC-wlan-radio-0/0] channel 20mhz 6
Warning: This action may cause service interruption. Continue?[Y/N]y
[AC-wlan-radio-0/0] eirp 127
[AC-wlan-radio-0/0] quit
# 配置AP射频1的信道和功率。
[AC-wlan-ap-0] radio 1
[AC-wlan-radio-0/1] channel 20mhz 149
Warning: This action may cause service interruption. Continue?[Y/N]y
[AC-wlan-radio-0/1] eirp 127
-!
[AC-wlan-radio-0/1] quit
[AC-wlan-ap-0] quit
11. 验证配置结果, WLAN业务配置会自动下发给AP，配置完成后，通过执行命令
display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP
对应的射频上的VAP已创建成功。
12. STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联
后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线
网络“wlan-net”中。
在STA3上做如下操作：
-!
-!
-!