你的位置：首页 > IT圈 > 4K IP智能威慑型子弹安防摄像机快速入门指南说明书

4K IP智能威慑型子弹安防摄像机快速入门指南说明书

IT圈 admin 2024-04-25 79浏览 0评论

2024年4月25日发(作者：拜访天)

The optimal installation location including height/angle for your camera will depend on the

type of detection settings that you want to enable. The optimal angle for person and vehicle

detection is different from the optimal angle for face detection. Based on your detection

preference choose between Step 1A or 1B.

• Angle the camera so that objects of interest appear in the bottom

⅔

of the camera image.

• Choose a location where objects of interest will be no further than 50ft (~15m) from the

camera.

Lower accuracy for objects further

away than 50ft (~15m) and/or in the

top ⅓ of the image.

Optimal accuracy for objects within

50ft (~15m) and in the bottom ⅔ of

the image.

STEP 1:

1A. Optimizing Person and Vehicle Detection Accuracy:

Quick Start Guide

•

Angle the camera between 30~60° down from the

level position.

Level position (i.e., ceiling)

•

4K IP Smart Deterrence Bullet Security Camera

•

Mounting Kit*

Ethernet Extension Cable with Pre-attached RJ45 Cable Gland*

* Per camera in multi-camera packs.

ATTENTION:

It is recommended to connect the camera to the NVR or an external PoE switch. If using a DC power adapter

(not included) with the camera, a REGULATED power supply is REQUIRED for use with this camera. Use of a

non-regulated, non-conforming power supply can damage this product and voids the warranty.

Dimensions

73mm

2.87”

6.87” / 175mm

70mm

2.76”

Safety Precautions

•

Use the camera only with compatible Lorex NVRs.

•

Read this guide carefully and keep it for future reference.

•

Follow all instructions for safe use of the product and handle with care.

Use the camera within given temperature, humidity and voltage levels noted in the camera’s

•

specifications.

•

Do not disassemble the camera.

•

Do not point the camera directly towards the sun or a source of intense light.

Use only a regulated power supply with the product (optional). Use of a non-regulated, non-

•

conforming power supply can damage the product and void the warranty.

Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based

•

cleaners.

Check the packaging of the included cable to verify cable grade based on model number.

The supplied cable is rated for surface and in-wall mounting.

CBL605U:

for surface mounting only. Cables for in-wall and floor-to-floor installations are sold separately (CMR

CBL100C5: The supplied cable is rated

type). These and other cables are available at .

Disclaimers

•

For a full list of compatible recorders, visit

To ensure that you are viewing camera video in full 4K resolution (4K monitor required), check the

/compatibility.

video output resolution of your recorder. For full instructions, see your recorder’s documentation at

•

Not intended for submersion in water. Installation in a sheltered location recommended.

This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/

Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is

normal, and indicates that the camera filter is working.

Need Help?

Visit us online for up-to-date software

and complete instruction manuals

Visit

number of your product

Search for the model

Click on your product

in the search results

Click on the Downloads tab

As our products are subject to continuous improvement, Lorex reserves the right to modify product design,

•

Install the camera between 8-16ft (2.5-5m) off of

the ground.

NOTE:

be influenced by multiple factors, such as the object’s

Accuracy of person and vehicle detection will

distance from the camera, the size of the object, and the

Optimal

height and angle of the camera. Night vision will also

angle

impact the accuracy of detection.

range

•

Additional Installation Tips:

•

Point the camera where there is the least amount of obstructions (e.g., tree branches).

•

Install the camera where vandals cannot easily reach.

•

Secure cabling so that it is not exposed or easily cut.

This camera is rated for outdoor use. Installation in a sheltered location is recommended.

•

The camera should be installed about 10 feet above the ground so as to ensure that the

1B. Optimizing Face Detection Accuracy:

full proportion of the face is detected on the screen.

• Angle the camera approximately 15° down from the level position.

•

To distinguish facial features the distance from the camera to the face should be

approximately 15 feet.

High Accuracy Face Detection Vs. Low Accuracy Face Detection

Accuracy of Face Detection will be influenced by the distance and angle of the face from the

camera. For optimal Face Detection the camera must be positioned head on to capture a

person’s entire face looking straight ahead. Obscured and/or partially or fully covered faces

(i.e. a person’s head tilted down to look at their phone) will not be accurately detected.

During low light conditions the camera will impact color night vision by switching to black &

white to ensure accuracy and improve detection range of Face Detection. If you cannot meet

the above requirements for installation it may be best to use person detection instead.

• Face Detection is only available up to two channels. You cannot enable both Face Detection

IMPORTANT:

• Face Detection is compatible with certain Lorex NVR’s only. For a list of compatible NVR’s

and Person and Vehicle Detection at the same time.

• Face Detection is disabled by default. For more information on Face Detection setup and

please visit /compatibility.

configuration, refer to the NVR’s manual at .

STEP 2: Installing the Camera

• Test your camera prior to selecting a permanent mounting location by temporarily connecting the

ATTENTION:

•

camera and cable to your NVR.

Review the section “STEP 1: Important Installation Guidelines” above before choosing a

permanent mounting location.

Before Installing the Camera

• Decide whether to run the cables through

the wall / ceiling (drilling required) or along

the wall / ceiling.

• If you run the cables along the wall /

ceiling, you must run the cable through the

cable notch

camera base flush to the surface when

on the base. This will keep the

mounted.

Cable Notch

To install your camera:

1. Use the included mounting template to mark holes for the screws.

2. Drill holes for the mounting screws.

NOTE: Insert the included drywall anchors if you are installing the camera in

3. Connect cables as shown in the section “Connecting the Camera”.

drywall.

4. Feed the cable through the mounting surface or cable notch and mount the

5. Use a Philips head screwdriver (not included) to loosen the adjustment screw

camera stand to the surface using the provided screws.

shown below. Adjust the camera position as needed:

• Tilt the camera

on the stand up

to 90°.

• Twist the camera

around the stand

360°.

Adjustment Screw

6. Tighten the adjustment screw to secure the position.

7. Remove the vinyl film from the camera lens when your installation is complete.

E892AB_QSG_EN_R2

Ethernet Cable

CameraNVR

Connect the other end of the Ethernet

cable to the NVR’s PoE ports. The camera

may take a minute to power up after being

connected.

12V DC Power

(Optional)

Connect the other end of the Ethernet

Connect the Ethernet cable to the

cable to a router or switch on your

camera.

network. See your NVR manual for details

on connecting the camera to

NOTE:

your NVR using a switch or router.

(model#:

A 12V DC power adapter

is only required if connecting the

ACCPWR12V1, not included)

camera’s Ethernet cable to a router or

switch that does not support PoE.

Using the RJ45 Cable Gland (Optional)

The pre-attached RJ45 cable gland covers the camera’s Ethernet connector and the RJ45

plug to provide weather-resistance and protection from dust, dirt and other environmental

contaminants.

To use the RJ45 cable gland:

Twist the RJ45 cable gland barrel

securely onto the camera Ethernet

connector.

RJ45 Cable

Gland Barrel

Camera Ethernet

Connector

NOTE:

additional sealing if it will be exposed to precipitation regularly.

The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for

Connecting the Cameras

Setup Diagram

Scenario 1: Connect Cameras to NVR

RouterNVRCamera

Scenario 2: Connect Cameras to Local Area Network (LAN)

Router

NVR

Camera

PoE Switch

• This camera is only compatible with select NVRs. For a list of compatible

ATTENTION:

•

recorders, visit

You must connect the camera to a supporting H.265 NVR to take advantage of

/compatibility.

H.265 compression. For instructions on enabling H.265 compression, visit

, and search for “How do I enable H.265 compression?”.

Cable Extension Options

Extend the Ethernet cable run for your camera up to 300ft (91m). See table below. It is

recommended to use UL CMR approved cables available at .

Cable TypeMax Cable Run DistanceMax # of Extensions

CAT5e (or higher) Ethernet cable300ft (91m)3

• You can use a RJ45 coupler or network switch (not included) to connect male ends of

•

Ethernet cable together.

To extend the cable run beyond 300ft (91m), a switch will be required (sold separately).

E892AB_QSG_EN_R2

Audio Settings

ATTENTION:

audio without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of

Audio recording and listen-in audio are disabled by default. Audio recording and/or use of listen-in

its products that does not conform with local laws.

To enable audio recording and listen-in audio:

1. From Live View, right-click and click

password.

Main Menu. Enter the system user name (default: admin) and

2. Click

3. Under

Camera and select Recording.

where the audio-capable camera

Channel, select the channel

4. Under

is connected.

Main Stream, click the

5. In the

Setting

More Setting

button.

recording and listen-in audio.

Enable Audio Encode

window:

for audio

NOTE:

a monitor with speakers or

Listen-in audio requires

speakers connected to the NVR.

Select the format that will be used to record audio.

6. Click

ACC

is recommended.

to save changes.

NOTE:

see your NVR’s instruction manual on

These instructions are based on current NVR interface. For the most up-to-date instructions,

Use your Lorex app to manually activate the camera's white light and siren features when

Using Deterrence Features

connected to a compatible Lorex recorder.

PREREQUISITE:

documentation.

Connect to your Lorex system using the app specified in your recorder

To activate deterrence features manually:

1. Launch the app and tap your recorder to view connected channels.

2. Tap a connected deterrence camera to open it in single-channel view.

3. Tap

to activate the white light, or tap to activate the siren.

NOTE:

triggered automatically when motion is detected. For full instructions, refer to the app manual on your

You can also set schedules and active areas of the camera image where the white light will be

product page at .

Troubleshooting

ProblemSolution

No picture / signal• Ensure the camera is connected to a compatible NVR. For full

•

compatibility, visit

The camera may take up to 1 minute to power up after being

/compatibility.

connected to the NVR. Wait two minutes before following the steps

•

below.

•

Ensure the camera is connected to your NVR or to your local network.

If you are not using PoE, you must connect the camera to a 12V DC

•

power adapter (not included).

If the camera is connected to the LAN, you must search your network

•

for cameras using the NVR. See the NVR’s instruction manual.

•

Ensure your NVR is properly connected to a monitor.

There may be an issue with your extension cable run. Connect the

camera to the NVR using a different Ethernet cable.

Picture does not appear

to be 4K

• To ensure that you are viewing camera video in full 4K resolution (4K

monitor required), check the video output resolution of your NVR. For

full instructions, see your NVR’s documentation at .

Picture is too bright• Ensure your camera isn’t pointed directly at a source of light (e.g., sun

•

or spot light).

•

Move your camera to a different location.

Check the brightness and contrast settings on the NVR.

Picture is too dark• Check the brightness and contrast settings on the NVR.

Night vision is not

working

• The night vision activates when light levels drop. The area may have

too much light.

Picture is not clear• Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a

•

soft, clean cloth.

Make sure that the cable run is within the limitations specified in the

•

section ‘Cable Extension Options’.

Remove the vinyl film from the camera lens when your installation is

complete.

Bright spot in video

when viewing camera

• Night vision reflects when pointing a camera through a window.

at night

Move the camera to a different location.

Picture is in color in dark

conditions

• This camera's image sensor is extra sensitive to light, meaning

that the camera stays in color mode at low-light conditions. For

instructions on how to make your camera switch to night mode, visit

mode?”.

, and search for “How do I make my camera switch to night

The camera warning

light is not switching on

• Ensure that you have enabled and configured white light deterrence

automatically

using a compatible NVR. See your NVR’s documentation for full

•

instructions.

Ensure the active areas and schedule for white light deterrence are

set properly. The default schedule for the warning light is night times

(between 5PM and 7AM).

The camera siren

is not switching on

• The camera siren cannot switch on automatically. You can control

automatically

the camera siren manually using a compatible Lorex NVR or app.

Refer to your NVR’s documentation for full instructions.

No audio• Audio is only supported on Lorex NVRs. For a list of compatible

•

recorders, visit

•

Ensure NVR volume is turned on / turned up.

/compatibility.

•

Ensure audio function on camera is turned on (see ‘Audio Settings’).

Ensure audio is turned up on viewing device.

Two-way talk not

working

• Use the Lorex app specified in your NVR documentation to activate

two-way talk. Tap

microphone on your mobile device. Tap again when finished speaking.

from the camera's live view, then speak into the