2024年5月29日发(作者：赧开宇)
手机设计Pro/ENGINEER手册
Mobile Phone Pro/Engineer Design Manual
徐国斌
/mobilemd
2005年
1
目录
前言...........................................................................................................3
1．Pro_stds的组成与应用......................................................................4
1.1 Pro_stds的组成............................................................................4
1.2 Pro_stds的应用............................................................................5
1.3 Pro_stds应用中的一些问题........................................................7
2．...........................................................................................8
2.1 文件的加载顺序.........................................................8
2.2 Company的标准........................................................8
2.3快捷键14
2.4 ...................................................................................15
3．公司标准........................................................................16
4．图纸设定文件..................................................................17
5．零件模板...........................................................................................17
6. 装配模板............................................................................................20
7．钣金件模板.......................................................................................22
8. 工程图................................................................................................25
8.25
8.2 工程图配置文件........................................................................25
9．Pro/Engineer 设计手机的总体思路................................................26
9.26
9.26
9.3 零件建模....................................................................................28
10．Pro/Engineer 完成设计后的检查..................................................29
10.1干涉检查...................................................................................29
10.2间隙检查...................................................................................30
10.3拔模检查...................................................................................31
11. Pro/Engineer建模的规则.................................................................32
11.1 零件的命名规则（暂缺）......................................................32
11.2 建模..........................................................................................33
12．Pro/Engineer 与PCB Layout的交互............................................34
12.1 Pro/Engineer中PCBA建模并输出到34
12.2 Pro/Engineer中输入PCB并PCBA建模
...............................34
13．公差分析.........................................................................................36
13.1 公差分析的方法......................................................................36
13.2 PCBA的公差分析...................................................................36
2
2024年5月29日发(作者：赧开宇)
手机设计Pro/ENGINEER手册
Mobile Phone Pro/Engineer Design Manual
徐国斌
/mobilemd
2005年
1
目录
前言...........................................................................................................3
1．Pro_stds的组成与应用......................................................................4
1.1 Pro_stds的组成............................................................................4
1.2 Pro_stds的应用............................................................................5
1.3 Pro_stds应用中的一些问题........................................................7
2．...........................................................................................8
2.1 文件的加载顺序.........................................................8
2.2 Company的标准........................................................8
2.3快捷键14
2.4 ...................................................................................15
3．公司标准........................................................................16
4．图纸设定文件..................................................................17
5．零件模板...........................................................................................17
6. 装配模板............................................................................................20
7．钣金件模板.......................................................................................22
8. 工程图................................................................................................25
8.25
8.2 工程图配置文件........................................................................25
9．Pro/Engineer 设计手机的总体思路................................................26
9.26
9.26
9.3 零件建模....................................................................................28
10．Pro/Engineer 完成设计后的检查..................................................29
10.1干涉检查...................................................................................29
10.2间隙检查...................................................................................30
10.3拔模检查...................................................................................31
11. Pro/Engineer建模的规则.................................................................32
11.1 零件的命名规则（暂缺）......................................................32
11.2 建模..........................................................................................33
12．Pro/Engineer 与PCB Layout的交互............................................34
12.1 Pro/Engineer中PCBA建模并输出到34
12.2 Pro/Engineer中输入PCB并PCBA建模
...............................34
13．公差分析.........................................................................................36
13.1 公差分析的方法......................................................................36
13.2 PCBA的公差分析...................................................................36
2