2024年6月15日发(作者：巩文心)

Seagate Shorting Technique

The Seagate shorting technique is a method used to troubleshoot and potentially

repair certain issues with Seagate hard drives. This technique involves shorting

specific pins on the drive's circuit board to initiate a diagnostic mode or reset

the drive.

Here are the general steps for performing a Seagate shorting technique:

Identify the Circuit Board: Locate the circuit board on the underside of the hard

drive. This is typically the smaller board with multiple components and wires

connected to it.

Locate the Shorting Points: Refer to a reliable repair guide or schematic to identify

the specific pins or points that need to be shorted. These points are typically

labeled and marked on the circuit board.

Prepare the Tools: Gather the necessary tools, such as a multimeter or a jumper wire.

A multimeter can be used to test for continuity between the pins, while a jumper

wire can be used to create a temporary connection between them.

Apply the Short: Carefully use the jumper wire or multimeter to create a connection

between the identified pins. Ensure that the connection is secure and stable.

Monitor the Drive: Observe the drive's response to the shorting. Depending on the

issue, the drive may enter a diagnostic mode, display error codes, or reset itself.

Repeat or Troubleshoot: If the initial shorting attempt does not yield any results,

refer back to the repair guide or schematic and try different pins or points.

Note: The Seagate shorting technique should only be attempted by experienced repair

personnel or those familiar with electronics. Incorrect shorting can damage the

drive or circuit board permanently.

希捷短接技巧是一种用于排查和可能修复希捷硬盘某些问题的方法。这种技巧涉及在硬盘电

路板上短接特定的引脚，以启动诊断模式或重置硬盘。

以下是执行希捷短接技巧的一般步骤：

识别电路板： 在硬盘底部找到电路板。这通常是较小的电路板，上面连接了多个组件和电

线。

定位短接点： 参考可靠的维修指南或原理图，确定需要短接的特定引脚或点。这些点通常

在电路板上标有标签和标记。

准备工具： 收集必要的工具，如万用表或跳线。万用表可用于测试引脚之间的连续性，而

跳线可用于在它们之间创建临时连接。

应用短接： 小心地使用跳线或万用表在确定的引脚之间创建连接。确保连接稳定可靠。

监控硬盘： 观察硬盘对短接的反应。根据问题，硬盘可能进入诊断模式，显示错误代码，

或自行重置。

重复或故障排除： 如果初次短接尝试没有结果，请参考维修指南或原理图，并尝试不同的

引脚或点。

注意： 希捷短接技巧应由经验丰富的维修人员或熟悉电子设备的人员尝试。错误的短接可

能会永久损坏硬盘或电路板。

2024年6月15日发(作者：巩文心)

Seagate Shorting Technique

The Seagate shorting technique is a method used to troubleshoot and potentially

repair certain issues with Seagate hard drives. This technique involves shorting

specific pins on the drive's circuit board to initiate a diagnostic mode or reset

the drive.

Here are the general steps for performing a Seagate shorting technique:

Identify the Circuit Board: Locate the circuit board on the underside of the hard

drive. This is typically the smaller board with multiple components and wires

connected to it.

Locate the Shorting Points: Refer to a reliable repair guide or schematic to identify

the specific pins or points that need to be shorted. These points are typically

labeled and marked on the circuit board.

Prepare the Tools: Gather the necessary tools, such as a multimeter or a jumper wire.

A multimeter can be used to test for continuity between the pins, while a jumper

wire can be used to create a temporary connection between them.

Apply the Short: Carefully use the jumper wire or multimeter to create a connection

between the identified pins. Ensure that the connection is secure and stable.

Monitor the Drive: Observe the drive's response to the shorting. Depending on the

issue, the drive may enter a diagnostic mode, display error codes, or reset itself.

Repeat or Troubleshoot: If the initial shorting attempt does not yield any results,

refer back to the repair guide or schematic and try different pins or points.

Note: The Seagate shorting technique should only be attempted by experienced repair

personnel or those familiar with electronics. Incorrect shorting can damage the

drive or circuit board permanently.

希捷短接技巧是一种用于排查和可能修复希捷硬盘某些问题的方法。这种技巧涉及在硬盘电

路板上短接特定的引脚，以启动诊断模式或重置硬盘。

以下是执行希捷短接技巧的一般步骤：

识别电路板： 在硬盘底部找到电路板。这通常是较小的电路板，上面连接了多个组件和电

线。

定位短接点： 参考可靠的维修指南或原理图，确定需要短接的特定引脚或点。这些点通常

在电路板上标有标签和标记。

准备工具： 收集必要的工具，如万用表或跳线。万用表可用于测试引脚之间的连续性，而

跳线可用于在它们之间创建临时连接。

应用短接： 小心地使用跳线或万用表在确定的引脚之间创建连接。确保连接稳定可靠。

监控硬盘： 观察硬盘对短接的反应。根据问题，硬盘可能进入诊断模式，显示错误代码，

或自行重置。

重复或故障排除： 如果初次短接尝试没有结果，请参考维修指南或原理图，并尝试不同的

引脚或点。

注意： 希捷短接技巧应由经验丰富的维修人员或熟悉电子设备的人员尝试。错误的短接可

能会永久损坏硬盘或电路板。