2024年7月24日发(作者：蚁博雅)
Diagnosis Menu
Figure 15-10. "Diagnosis : Teach-Box Diagnosis" dialog box
w
Turns ON/OFF all Speed LEDs.
w
Turns ON/OFF all Axis LEDs.
w
Turns ON/OFF all Mode LEDs.
w
Turns ON/OFF all Vacuum LEDs.
w
Turns ON/OGG all LEDs.
w
Closes the dialog box.
During teaching, the operator or people near the operator
could be injured due to operation error or insufficient
checking of surroundings.
Warning
Before start teaching, check the device to teach one more
time, and check whether there is any worker near the
machine.
15.6. On Axis [F8]
Used to compensate the movement error in driving the X-axis and the Y-axis motors, a
compensation value for the movement error in driving each axis can be entered after
15-11
Samsung Component Placer CP-60L Operations Manual
measuring the degree of the movement error in driving each axis for the machine by using
the laser sensor.
Figure 15-11. "XY On Axis Test and Setting" dialog box
w
§
Select the axis to be measured.
§
Select the distance to move in each step for measurement.
§
It is marked after measurement is completed.
w
§ < Step Left> button
Moves the head to the left by one step.
§
Moves the head to the right by one step.
§
Moves to the measurement starting position.
§
Moves the head to the middle position between the measurement starting point
and the measurement end point.
§
Moves to the measurement ending position.
w
§
15-12
Diagnosis Menu
An option selected when aligning the laser sensor beam.
§
An option used when measuring the precision in driving the corresponding axis
motor by using the laser sensor.
§ Step Count
A value decided by the step size and axis stroke.
§
The resting time after moving the head to the position to be measured. As the
laser sensor can not measure if this time is too short, the set value must be used.
§
An input window to set the number of trips between the Start Point and the End
Point.
§
Moves the head to the starting position for measurement.
§
Starts measurement from the start position. The head moves according to the step
size, step count and cycle count.
§
Stops measurement.
w
Check it to use Compensation data.
w
Imports the data measured to compensate the movement error in driving the
corresponding axis motor.
w
Applies the imported measurement data.
During teaching, the operator or people near the operator
could be injured due to operation error or insufficient
checking of surroundings.
Before start teaching, check the device to teach one
more time, and check whether there is any worker near
the machine.
Warning
15-13
2024年7月24日发(作者：蚁博雅)
Diagnosis Menu
Figure 15-10. "Diagnosis : Teach-Box Diagnosis" dialog box
w
Turns ON/OFF all Speed LEDs.
w
Turns ON/OFF all Axis LEDs.
w
Turns ON/OFF all Mode LEDs.
w
Turns ON/OFF all Vacuum LEDs.
w
Turns ON/OGG all LEDs.
w
Closes the dialog box.
During teaching, the operator or people near the operator
could be injured due to operation error or insufficient
checking of surroundings.
Warning
Before start teaching, check the device to teach one more
time, and check whether there is any worker near the
machine.
15.6. On Axis [F8]
Used to compensate the movement error in driving the X-axis and the Y-axis motors, a
compensation value for the movement error in driving each axis can be entered after
15-11
Samsung Component Placer CP-60L Operations Manual
measuring the degree of the movement error in driving each axis for the machine by using
the laser sensor.
Figure 15-11. "XY On Axis Test and Setting" dialog box
w
§
Select the axis to be measured.
§
Select the distance to move in each step for measurement.
§
It is marked after measurement is completed.
w
§ < Step Left> button
Moves the head to the left by one step.
§
Moves the head to the right by one step.
§
Moves to the measurement starting position.
§
Moves the head to the middle position between the measurement starting point
and the measurement end point.
§
Moves to the measurement ending position.
w
§
15-12
Diagnosis Menu
An option selected when aligning the laser sensor beam.
§
An option used when measuring the precision in driving the corresponding axis
motor by using the laser sensor.
§ Step Count
A value decided by the step size and axis stroke.
§
The resting time after moving the head to the position to be measured. As the
laser sensor can not measure if this time is too short, the set value must be used.
§
An input window to set the number of trips between the Start Point and the End
Point.
§
Moves the head to the starting position for measurement.
§
Starts measurement from the start position. The head moves according to the step
size, step count and cycle count.
§
Stops measurement.
w
Check it to use Compensation data.
w
Imports the data measured to compensate the movement error in driving the
corresponding axis motor.
w
Applies the imported measurement data.
During teaching, the operator or people near the operator
could be injured due to operation error or insufficient
checking of surroundings.
Before start teaching, check the device to teach one
more time, and check whether there is any worker near
the machine.
Warning
15-13