2024年7月24日发(作者：戢苇然)
Samsung Component Placer CP-60L Operations Manual
Displays the current position of each axis based on the origin of the coordinate
system.
w Axis Position
Displays the current position in the Encoder Pulse value based on the position of each
axis when the power is turned on.
w Encoder Position
Displays the position of each axis in the Encoder Pulse value based on the position
where the motor Encoder found the Index.
w Head Drop-down
Displays a list of Z axis and Theta axis corresponding to the currently selected gantry.
15.2. Conveyor [F3]
Checks the status of various devices in the Conveyor group. When this button is clicked
on, the following dialog box is displayed.
Figure 15-6. " Conveyor – Status " dialog box
15.2.1. Conveyor – Status
The status of various sensors related to the Conveyor can be checked and the functions
related to rail width control and vacuum can be inspected. Displays the status of board for
each station (No Board, Have Board, or Releasing Board).
w
Used to load PCBs in the corresponding Station.
w
15-6
Diagnosis Menu
Used to release PCBs from the corresponding Station.
w Sensors
Indicates whether the Conveyor sensors are sensed.
w Stopper
Can move Up/Down the Stopper.
w
§
Used to extend the rail to the conveyor width wanted. Enter the value of desired
width in the edit box below.
§ Stopper
Moves Up/Down the Stopper.
BUT
Moves Up/Down the Back-Up Table.
§ Edge Fixer
Tests the operation of Edge Fixer.
§ Hole Fixer
Tests the operation of Hole Fixer.
§ Zones
Tests the Zone sensor related to Conveyor width control.
15.2.2. Conveyor – Controls
On this widow, Conveyor functions can be manipulated manually and the SMEMA
Control Diagnostics function is activated.
15-7
Samsung Component Placer CP-60L Operations Manual
Figure 15-7. “Conveyor-Controls” dialog box
w
Initializes the Conveyor setup parameters at each Station to 0.
w
Switches the Conveyor Belt control at each Station to manual or automatic.
w
Executes manual belt adjustment at each Station.
w
Stops manual belt adjustment at each Station.
w SMEMA Control
Tests the SMEMA Control signals individually.
w
Sends a PCB request signal to the previous machine. (Yes, No)
w
Receives a PCB input signal from the precious machine. (Yes, No)
w
Receives a PCB request signal from the next machine. (Yes, No)
w
Sends a PCB output signal to the next machine. (Yes, No)
15-8
Diagnosis Menu
Caution
Adjusting the conveyor width without checking conveyor
obstruction or the existence of foreign substance could
damage the conveyor.
Be sure to check conveyor obstruction and the existence
of foreign substance before adjusting the conveyor width.
15.3. Light [F4]
Checks the lighting devices attached on the Move Camera, Fly Camera, and Fix Camera.
When this button is clicked on, the following dialog box is displayed.
Figure 15-8. " Camera Light Diagnosis " dialog box
w
Select the DownCamera. Then, the selection item in the
is decided. For the Down Camera, set inner and outer lighting.
w
Select the LSOCamera. Then, the selection item in the
is decided. For the LSO Camera, set inner, middle and outer lighting.
w
Select the camera to adjust lighting.
w
Set the lighting value. Set the value by adjusting the corresponding slide bar.
§ Inner
Adjust the Inner lighting attached on the front of the camera.
§ Middle
Adjust the middle lighting attached on the front of the camera.
§ Outer
Adjust the outer lighting attached on the front of the camera.
w
Closes this dialog box.
15-9
2024年7月24日发(作者：戢苇然)
Samsung Component Placer CP-60L Operations Manual
Displays the current position of each axis based on the origin of the coordinate
system.
w Axis Position
Displays the current position in the Encoder Pulse value based on the position of each
axis when the power is turned on.
w Encoder Position
Displays the position of each axis in the Encoder Pulse value based on the position
where the motor Encoder found the Index.
w Head Drop-down
Displays a list of Z axis and Theta axis corresponding to the currently selected gantry.
15.2. Conveyor [F3]
Checks the status of various devices in the Conveyor group. When this button is clicked
on, the following dialog box is displayed.
Figure 15-6. " Conveyor – Status " dialog box
15.2.1. Conveyor – Status
The status of various sensors related to the Conveyor can be checked and the functions
related to rail width control and vacuum can be inspected. Displays the status of board for
each station (No Board, Have Board, or Releasing Board).
w
Used to load PCBs in the corresponding Station.
w
15-6
Diagnosis Menu
Used to release PCBs from the corresponding Station.
w Sensors
Indicates whether the Conveyor sensors are sensed.
w Stopper
Can move Up/Down the Stopper.
w
§
Used to extend the rail to the conveyor width wanted. Enter the value of desired
width in the edit box below.
§ Stopper
Moves Up/Down the Stopper.
BUT
Moves Up/Down the Back-Up Table.
§ Edge Fixer
Tests the operation of Edge Fixer.
§ Hole Fixer
Tests the operation of Hole Fixer.
§ Zones
Tests the Zone sensor related to Conveyor width control.
15.2.2. Conveyor – Controls
On this widow, Conveyor functions can be manipulated manually and the SMEMA
Control Diagnostics function is activated.
15-7
Samsung Component Placer CP-60L Operations Manual
Figure 15-7. “Conveyor-Controls” dialog box
w
Initializes the Conveyor setup parameters at each Station to 0.
w
Switches the Conveyor Belt control at each Station to manual or automatic.
w
Executes manual belt adjustment at each Station.
w
Stops manual belt adjustment at each Station.
w SMEMA Control
Tests the SMEMA Control signals individually.
w
Sends a PCB request signal to the previous machine. (Yes, No)
w
Receives a PCB input signal from the precious machine. (Yes, No)
w
Receives a PCB request signal from the next machine. (Yes, No)
w
Sends a PCB output signal to the next machine. (Yes, No)
15-8
Diagnosis Menu
Caution
Adjusting the conveyor width without checking conveyor
obstruction or the existence of foreign substance could
damage the conveyor.
Be sure to check conveyor obstruction and the existence
of foreign substance before adjusting the conveyor width.
15.3. Light [F4]
Checks the lighting devices attached on the Move Camera, Fly Camera, and Fix Camera.
When this button is clicked on, the following dialog box is displayed.
Figure 15-8. " Camera Light Diagnosis " dialog box
w
Select the DownCamera. Then, the selection item in the
is decided. For the Down Camera, set inner and outer lighting.
w
Select the LSOCamera. Then, the selection item in the
is decided. For the LSO Camera, set inner, middle and outer lighting.
w
Select the camera to adjust lighting.
w
Set the lighting value. Set the value by adjusting the corresponding slide bar.
§ Inner
Adjust the Inner lighting attached on the front of the camera.
§ Middle
Adjust the middle lighting attached on the front of the camera.
§ Outer
Adjust the outer lighting attached on the front of the camera.
w
Closes this dialog box.
15-9