最新消息: USBMI致力于为网友们分享Windows、安卓、IOS等主流手机系统相关的资讯以及评测、同时提供相关教程、应用、软件下载等服务。

得胜DA10演讲咪用户手册说明书

IT圈 admin 72浏览 0评论

2024年9月26日发(作者:甄钰)

DA10

演讲咪

■ 前言

尊敬的用户:

感谢您选购得胜DA10演讲咪,为了您能够更好的了解及使

用本产品,建议您在使用前仔细阅读本说明书。

若存在有疑问或者您有宝贵的建议,可通过

拨打得胜官方服务热线400 6828 333或微信扫描

二维码关注得胜官方公众号与我们联系。

■ 产品特性

集麦克风、功放、扬声器于一体的演讲咪,适用于演讲、宣

传、K歌娱乐等场合;

采用稀土扬声器,重量轻、音质好、声音大、峰值功率8W;

一键切换喊话及K歌模式,操作简便;

具备无线播放功能,简化繁琐的线材连接,无线播放音乐更方

便,更自由;

具有音量调节功能,可根据使用的场合情况调整扩音音量;

内置DSP啸叫抑制芯片,有效抑制啸叫声;

超长待机,节能省电,停止使用15分钟后自动关机;

内置大容量锂电池,节能环保,使用时间约8小时;

小巧轻便,握感舒适,适合长时间手持扩音及K歌娱乐。

■ 适用范围

应用于讲话、宣传、K歌等场合。

01

DA10

演讲咪

■ 产品配置

DA 10演讲咪………………………………………………………1个

防风棉…………………………………………………………1个

Type-C充电线…………………………………………………1条

使用手册………………………………………………………1份

■ 技术参数

主机参数

频率响应: 100Hz-15kHz

峰值功率:8W

扬声器阻抗:4Ω

总谐波失真:THD≤5% 1KHz@4R,4W

信噪比:66dB (A-Weighted)@1W 4Ω(演讲模式)

蓝牙版本:5.0

混响模式:Reverb

工作电压:3.4V-4.2V

电池类型:锂离子电池(18650)

电池容量:3.7V/2000mAh

充电方式:DC5V 1.5A

充电时间:约3小时

使用时间:约8小时(演讲模式)

产品重量:约220g

产品尺寸:Φ64mm*235mm(直径*高)

02

DA10

演讲咪

音头参数

拾音器:背极式驻极体

指向性:单指向

频率响应:150Hz-16KHz

灵敏度:-47.5±1.5dB(0dB=1V/Pa,at 1KHz)

注:以上数据由得胜实验室测试得到,并拥有最终解释权!

■ 功能示意

03

DA10

演讲咪

① 电源键:长按电源键2秒,开启或关闭扩音器。15分钟后不使

用,将自动关机;

② “M”按键:循环点按切换4种工作模式:演讲模式、主持模

式、K歌模式、蓝牙模式,切换时伴随对应提示音。

③ 指示灯:电量充足时,指示灯常亮绿灯。电量少于1小时时,

指示灯常亮红灯。充电状态时,指示灯闪烁红灯。充满电状

态时,指示灯长亮绿灯。

④“ + ”按键:点按增加扩音器音量,共3档音量可调节;

⑤“ - ”按键:点按减小扩音器音量,减到最小时约为总音量的

60%,无静音功能;

⑥ 拾音器:喊话时嘴要尽量靠近拾音器,一般保持3-5厘米为

宜。不能用手捂住拾音器部分,否则容易生产啸叫;

⑦ 充电接口:连接Type-C充电线,请使用规格为5V 1.5A且经

过3C认证的充电头为扩音器充电;

⑧ 扩音器喇叭:喊话时不要靠近人耳,以免造成听力受损。请

尽量保持喇叭清洁。

提示:初次使用时,建议先充满电;当电池充满时,请停止对电

池充电,避免电池过充;如长时间不用,需每半年充电一次,避

免电池过放,对电池性能产生影响。

04

DA10

演讲咪

握持示意图

■ 无线配对方法

首次使用本机时,需要与手机或无线播放设备配对连接,操作步

骤如下:

1.打开演讲咪电源开关,点按“M”键切换至蓝牙模式;

2.此时打开手机的“设置”菜单,找到无线连接功能选项,开启

手机的无线播放功能,待搜索到“TAKSTAR DA10”,点击

“TAKSTAR DA10”进行连接,当演讲咪可以进行无线播放声

音,则表示设备已连接成功。

3.下次切换至蓝牙模式时,如果是已经进行过无线连接,则自动

回连;在无线连接成功的情况下,切换到其他工作模式则自动

断开无线连接。

05

DA10

演讲咪

■ 安全警示

为避免电击、高温、着火、辐射、爆炸、机械危险以及使用

不当等可能造成的人身伤害或财产损失,使用本产品前,请

仔细阅读并遵守以下事项:

1. 请勿将喇叭靠近人耳,以免造成听力损伤;

2. 使用中若发现有异常(如冒烟、异味等),请立即关闭电源开

关并拔掉电源插头,然后将产品送经销商检修;

3. 本产品及附件都应放置在室内干燥通风处,勿长期存放在潮

湿、灰尘多的环境;使用中避免靠近火源、雨淋、进水、过度

碰撞、抛掷、振动本机及覆盖通风孔,以免损坏其功能;

4. 使用该产品时需遵守相关安全规定,法律法规明确禁止使用场

合请勿使用本机,以免导致意外事故;

5. 请不要自行拆机改装或维修,以防止出现人身伤害,如有问题

或服务需求请联系当地经销商跟进处理;

6. 消费者若使用电源适配器供电,则应购买配套使用获得CCC认

证并满足标准要求的电源适配器。

06

DA 10

Speech Microphone

■ Product

Dear Customer,

Thank you for purchasing TAKSTAR DA10 speech microphone.

Please read the user manual carefully before operation and

keep it for reference in future. If you have any questions or

suggestions, please contact our local dealer.

■ Features

Combining microphone, power amplifier and speaker

together, suitable for speech, publicity, karaoke

Rare earth material speaker, light weight, excellent sound,

high volume, peak power 8W

One button to switch between MC mode and KTV mode,

easy operation

Wireless playing function without the trouble of cable

connection, more convenient to play music

Volume adjusting function to adjust the volume based on

the venue

Built-in DSP chip with the feedback rejecting function to

reject feedback effectively

Ultra-long standby, turning off automatically after no signal

input for 15 minutes to save the power consumption

High capacity Lithium battery for energy saving and

environmental protection, approximately 8h operation time

Compact design, comfortable to hold, suitable for

reinforcement and karaoke for a long time

07

DA 10

Speech Microphone

■ Application

Speech, publicity, karaoke, etc.

■ Product content

DA 10 speech microphone………………………………………1 pc

Windscreen………………………………………………………1pc

Type-C charging cable…………………………………………1pc

User manual………………………………………………………1 pc

■ Specification

Specification

Frequency Response: 100Hz-15kHz

Peak Power: 8W

Speaker Impedance: 4Ω

THD: THD≤5% 1KHz@4R,4W

S/N Ratio: 66dB (A-Weighted)@1W 4Ω (speech mode)

Bluetooth Version: 5.0

Reverb: Reverb

Operating Voltage: 3.4V-4.2V

Battery Type: Li-ion battery (18650)

Battery Capacity: 3.7V/2000mAh

Charging: DC5V 1.5A

Charging Time: approx. 3h

Operation Time: approx. 8h (speech)

Net Weight: approx. 220g

Dimension: Φ64mm*235mm (Dia*H)

08

DA 10

Speech Microphone

Cartridge Specification

Cartridge: back electret

Polar Pattern: unidirectional

Frequency Response: 150Hz-16KHz

Sensitivity: -47.5±1.5dB(0dB=1V/Pa,at 1KHz)

Note: The data is tested by Takstar Laboratory and Takstar has the

final interpretation right!

■ Function

① Power button: Keep pressing it for 2 seconds to turn on or

off the amplifier. If it is not used for 15 minutes, it will

automatically power off.

09

DA 10

Speech Microphone

② "M" button: Click it to cycle through 4 modes (i.e., speech

mode, host mode, karaoke mode, Bluetooth mode),

accompanied by corresponding voice prompt.

③ Indicator light: If it keeps lighting up green during

operation, this means sufficient power supply. If the power

can last for less than 1h, it keeps lighting up red. It flashes

red when charged. If it keeps lighting up green, this means

it is fully charged.

④ "+" button: Click it to increase the volume of the amplifier.

A total of 3 levels of volume can be chosen.

⑤ "-" button: Click it to decrease the volume of the amplifier.

It can only be minimized to about 60% of the total volume.

There is no mute function.

⑥ Cartridge: When speaking, the mouth should be as close

as possible to the pickup, generally 3-5 cm. Do not cover

the cartridge with your hands; otherwise it will easily

produce feedback.

⑦ Charging interface: Connect to the Type-C charging cable.

Please use a charging head with a specification of 5V 1.5A

and 3C certification to charge the amplifier.

⑧ Speaker: Do not put the speaker too close to people's ears

to avoid hearing damaging. Please try to keep the speaker

clean.

Note: When the product is used for the first time, it is

recommended to fully charge it first; when it is fully charged,

please stop charging the battery to avoid overcharge; if it is

10

DA 10

Speech Microphone

not used for a long time, it needs to be charged once every six

months to avoid over discharge of the battery, which will

affect the battery performance.

Holding diagram

Wireless pairing method

Upon first use, you need to connect to your phone or a

wireless device, following below steps:

1. Power up the mic and press “M” button to switch to

Bluetooth mode.

2. Enter SETTINGS menu on your phone, find and enable

Bluetooth, wait until “TAKSTAR DA10” is discovered and

tap on it to connect. If connected successfully, you should

be able to play audio wirelessly through the mic.

3. Next time you switch to Bluetooth mode, it will

automatically pair to the previously connected device.

Switching to other mode will disable wireless connection

automatically.

11

DA 10

Speech Microphone

■ Caution

In order to avoid possible personal injury or property

damage caused by electric shock, high temperature, fire,

radiation, explosion, mechanical hazards and improper use,

please read and observe the following items carefully before

using the product.

1. Please do not put the speaker close to people's ears to

avoid hearing damage.

2. If there is any abnormality (such as smoke, odor, etc.)

during use, please turn off the power switch and unplug the

power plug immediately, and then send the product to the

dealer for maintenance.

3. The product and accessories should be placed indoors in a

dry and ventilated place. Do not store them in a humid and

dusty environment for a long time. Avoid getting close to

fire, rain, water, excessive collision, throwing, vibrating the

machine and covering the ventilation holes during use, so

as not to damage its function.

4. When using the product, you must abide by the relevant

safety regulations. Please do not use the product in the

occasions that are clearly prohibited by laws and

regulations to avoid accidents.

5. Please do not disassemble, refit or repair the product by

yourself to prevent personal injury. If you have any

questions or service needs, please contact our local dealer

for follow-up.

6. If you use a power adapter to supply power, you should

purchase and use a power adapter that has obtained CCC

certification and meets the standard requirements.

12

DA 10

Speech Microphone

13

DA 10

Speech Microphone

14

2024年9月26日发(作者:甄钰)

DA10

演讲咪

■ 前言

尊敬的用户:

感谢您选购得胜DA10演讲咪,为了您能够更好的了解及使

用本产品,建议您在使用前仔细阅读本说明书。

若存在有疑问或者您有宝贵的建议,可通过

拨打得胜官方服务热线400 6828 333或微信扫描

二维码关注得胜官方公众号与我们联系。

■ 产品特性

集麦克风、功放、扬声器于一体的演讲咪,适用于演讲、宣

传、K歌娱乐等场合;

采用稀土扬声器,重量轻、音质好、声音大、峰值功率8W;

一键切换喊话及K歌模式,操作简便;

具备无线播放功能,简化繁琐的线材连接,无线播放音乐更方

便,更自由;

具有音量调节功能,可根据使用的场合情况调整扩音音量;

内置DSP啸叫抑制芯片,有效抑制啸叫声;

超长待机,节能省电,停止使用15分钟后自动关机;

内置大容量锂电池,节能环保,使用时间约8小时;

小巧轻便,握感舒适,适合长时间手持扩音及K歌娱乐。

■ 适用范围

应用于讲话、宣传、K歌等场合。

01

DA10

演讲咪

■ 产品配置

DA 10演讲咪………………………………………………………1个

防风棉…………………………………………………………1个

Type-C充电线…………………………………………………1条

使用手册………………………………………………………1份

■ 技术参数

主机参数

频率响应: 100Hz-15kHz

峰值功率:8W

扬声器阻抗:4Ω

总谐波失真:THD≤5% 1KHz@4R,4W

信噪比:66dB (A-Weighted)@1W 4Ω(演讲模式)

蓝牙版本:5.0

混响模式:Reverb

工作电压:3.4V-4.2V

电池类型:锂离子电池(18650)

电池容量:3.7V/2000mAh

充电方式:DC5V 1.5A

充电时间:约3小时

使用时间:约8小时(演讲模式)

产品重量:约220g

产品尺寸:Φ64mm*235mm(直径*高)

02

DA10

演讲咪

音头参数

拾音器:背极式驻极体

指向性:单指向

频率响应:150Hz-16KHz

灵敏度:-47.5±1.5dB(0dB=1V/Pa,at 1KHz)

注:以上数据由得胜实验室测试得到,并拥有最终解释权!

■ 功能示意

03

DA10

演讲咪

① 电源键:长按电源键2秒,开启或关闭扩音器。15分钟后不使

用,将自动关机;

② “M”按键:循环点按切换4种工作模式:演讲模式、主持模

式、K歌模式、蓝牙模式,切换时伴随对应提示音。

③ 指示灯:电量充足时,指示灯常亮绿灯。电量少于1小时时,

指示灯常亮红灯。充电状态时,指示灯闪烁红灯。充满电状

态时,指示灯长亮绿灯。

④“ + ”按键:点按增加扩音器音量,共3档音量可调节;

⑤“ - ”按键:点按减小扩音器音量,减到最小时约为总音量的

60%,无静音功能;

⑥ 拾音器:喊话时嘴要尽量靠近拾音器,一般保持3-5厘米为

宜。不能用手捂住拾音器部分,否则容易生产啸叫;

⑦ 充电接口:连接Type-C充电线,请使用规格为5V 1.5A且经

过3C认证的充电头为扩音器充电;

⑧ 扩音器喇叭:喊话时不要靠近人耳,以免造成听力受损。请

尽量保持喇叭清洁。

提示:初次使用时,建议先充满电;当电池充满时,请停止对电

池充电,避免电池过充;如长时间不用,需每半年充电一次,避

免电池过放,对电池性能产生影响。

04

DA10

演讲咪

握持示意图

■ 无线配对方法

首次使用本机时,需要与手机或无线播放设备配对连接,操作步

骤如下:

1.打开演讲咪电源开关,点按“M”键切换至蓝牙模式;

2.此时打开手机的“设置”菜单,找到无线连接功能选项,开启

手机的无线播放功能,待搜索到“TAKSTAR DA10”,点击

“TAKSTAR DA10”进行连接,当演讲咪可以进行无线播放声

音,则表示设备已连接成功。

3.下次切换至蓝牙模式时,如果是已经进行过无线连接,则自动

回连;在无线连接成功的情况下,切换到其他工作模式则自动

断开无线连接。

05

DA10

演讲咪

■ 安全警示

为避免电击、高温、着火、辐射、爆炸、机械危险以及使用

不当等可能造成的人身伤害或财产损失,使用本产品前,请

仔细阅读并遵守以下事项:

1. 请勿将喇叭靠近人耳,以免造成听力损伤;

2. 使用中若发现有异常(如冒烟、异味等),请立即关闭电源开

关并拔掉电源插头,然后将产品送经销商检修;

3. 本产品及附件都应放置在室内干燥通风处,勿长期存放在潮

湿、灰尘多的环境;使用中避免靠近火源、雨淋、进水、过度

碰撞、抛掷、振动本机及覆盖通风孔,以免损坏其功能;

4. 使用该产品时需遵守相关安全规定,法律法规明确禁止使用场

合请勿使用本机,以免导致意外事故;

5. 请不要自行拆机改装或维修,以防止出现人身伤害,如有问题

或服务需求请联系当地经销商跟进处理;

6. 消费者若使用电源适配器供电,则应购买配套使用获得CCC认

证并满足标准要求的电源适配器。

06

DA 10

Speech Microphone

■ Product

Dear Customer,

Thank you for purchasing TAKSTAR DA10 speech microphone.

Please read the user manual carefully before operation and

keep it for reference in future. If you have any questions or

suggestions, please contact our local dealer.

■ Features

Combining microphone, power amplifier and speaker

together, suitable for speech, publicity, karaoke

Rare earth material speaker, light weight, excellent sound,

high volume, peak power 8W

One button to switch between MC mode and KTV mode,

easy operation

Wireless playing function without the trouble of cable

connection, more convenient to play music

Volume adjusting function to adjust the volume based on

the venue

Built-in DSP chip with the feedback rejecting function to

reject feedback effectively

Ultra-long standby, turning off automatically after no signal

input for 15 minutes to save the power consumption

High capacity Lithium battery for energy saving and

environmental protection, approximately 8h operation time

Compact design, comfortable to hold, suitable for

reinforcement and karaoke for a long time

07

DA 10

Speech Microphone

■ Application

Speech, publicity, karaoke, etc.

■ Product content

DA 10 speech microphone………………………………………1 pc

Windscreen………………………………………………………1pc

Type-C charging cable…………………………………………1pc

User manual………………………………………………………1 pc

■ Specification

Specification

Frequency Response: 100Hz-15kHz

Peak Power: 8W

Speaker Impedance: 4Ω

THD: THD≤5% 1KHz@4R,4W

S/N Ratio: 66dB (A-Weighted)@1W 4Ω (speech mode)

Bluetooth Version: 5.0

Reverb: Reverb

Operating Voltage: 3.4V-4.2V

Battery Type: Li-ion battery (18650)

Battery Capacity: 3.7V/2000mAh

Charging: DC5V 1.5A

Charging Time: approx. 3h

Operation Time: approx. 8h (speech)

Net Weight: approx. 220g

Dimension: Φ64mm*235mm (Dia*H)

08

DA 10

Speech Microphone

Cartridge Specification

Cartridge: back electret

Polar Pattern: unidirectional

Frequency Response: 150Hz-16KHz

Sensitivity: -47.5±1.5dB(0dB=1V/Pa,at 1KHz)

Note: The data is tested by Takstar Laboratory and Takstar has the

final interpretation right!

■ Function

① Power button: Keep pressing it for 2 seconds to turn on or

off the amplifier. If it is not used for 15 minutes, it will

automatically power off.

09

DA 10

Speech Microphone

② "M" button: Click it to cycle through 4 modes (i.e., speech

mode, host mode, karaoke mode, Bluetooth mode),

accompanied by corresponding voice prompt.

③ Indicator light: If it keeps lighting up green during

operation, this means sufficient power supply. If the power

can last for less than 1h, it keeps lighting up red. It flashes

red when charged. If it keeps lighting up green, this means

it is fully charged.

④ "+" button: Click it to increase the volume of the amplifier.

A total of 3 levels of volume can be chosen.

⑤ "-" button: Click it to decrease the volume of the amplifier.

It can only be minimized to about 60% of the total volume.

There is no mute function.

⑥ Cartridge: When speaking, the mouth should be as close

as possible to the pickup, generally 3-5 cm. Do not cover

the cartridge with your hands; otherwise it will easily

produce feedback.

⑦ Charging interface: Connect to the Type-C charging cable.

Please use a charging head with a specification of 5V 1.5A

and 3C certification to charge the amplifier.

⑧ Speaker: Do not put the speaker too close to people's ears

to avoid hearing damaging. Please try to keep the speaker

clean.

Note: When the product is used for the first time, it is

recommended to fully charge it first; when it is fully charged,

please stop charging the battery to avoid overcharge; if it is

10

DA 10

Speech Microphone

not used for a long time, it needs to be charged once every six

months to avoid over discharge of the battery, which will

affect the battery performance.

Holding diagram

Wireless pairing method

Upon first use, you need to connect to your phone or a

wireless device, following below steps:

1. Power up the mic and press “M” button to switch to

Bluetooth mode.

2. Enter SETTINGS menu on your phone, find and enable

Bluetooth, wait until “TAKSTAR DA10” is discovered and

tap on it to connect. If connected successfully, you should

be able to play audio wirelessly through the mic.

3. Next time you switch to Bluetooth mode, it will

automatically pair to the previously connected device.

Switching to other mode will disable wireless connection

automatically.

11

DA 10

Speech Microphone

■ Caution

In order to avoid possible personal injury or property

damage caused by electric shock, high temperature, fire,

radiation, explosion, mechanical hazards and improper use,

please read and observe the following items carefully before

using the product.

1. Please do not put the speaker close to people's ears to

avoid hearing damage.

2. If there is any abnormality (such as smoke, odor, etc.)

during use, please turn off the power switch and unplug the

power plug immediately, and then send the product to the

dealer for maintenance.

3. The product and accessories should be placed indoors in a

dry and ventilated place. Do not store them in a humid and

dusty environment for a long time. Avoid getting close to

fire, rain, water, excessive collision, throwing, vibrating the

machine and covering the ventilation holes during use, so

as not to damage its function.

4. When using the product, you must abide by the relevant

safety regulations. Please do not use the product in the

occasions that are clearly prohibited by laws and

regulations to avoid accidents.

5. Please do not disassemble, refit or repair the product by

yourself to prevent personal injury. If you have any

questions or service needs, please contact our local dealer

for follow-up.

6. If you use a power adapter to supply power, you should

purchase and use a power adapter that has obtained CCC

certification and meets the standard requirements.

12

DA 10

Speech Microphone

13

DA 10

Speech Microphone

14

发布评论

评论列表 (0)

  1. 暂无评论