2024年9月28日发(作者：悉安翔)
df-60334:A1 • A1-100
MS-9600LS(E)/MS-9600UDLS(E)
Intelligent Addressable FACP
with Optional 2nd Loop
Addressable
General
Fire•Lite’s MS-9600LS(E) and MS-9600UDLS(E) are compact,
cost effective, intelligent addressable FACPs (Fire Alarm Con-
trol Panels) with an extensive list of powerful features. The
combination of Fire•Lite’s newer series devices and legacy
300 Series devices, along with the MS-9600LS(E) or
MS-9600UDLSE FACP, offer the latest in fire protection tech-
nology. LiteSpeed™ is a patented technology that polls 10
devices at a time looking for new or different information.
When new information is found at a specific address, the sys-
tem polls that device several times for any new data. This
improvement allows a fully loaded panel with up to 636
devices to report an incident and activate the notification cir-
cuits in under 10 seconds. With this new polling scheme,
devices can be wired on standard twisted, unshielded wire up
to a distance of 10,000 feet per loop. Each Signaling Line Cir-
cuit (SLC) loop supports up to 159 addressable detectors
including photoelectric, photoelectric with heat, beam, ioniza-
tion, photoelectric duct, fixed heat, fixed heat with rate-of-rise,
and fixed high-heat detectors. It also supports up to 159
addressable modules including monitor (two-wire detector,
normally open devices), dual-monitor functions (two monitor
circuits from one module, two addresses used), multimonitor
(multiple monitor circuits from one module, multiple addresses
used), control (for Notification Appliance Circuits), and relay
(two Form-C) modules.
The FLPS-7 power supply is a separate board while all other
electronics are contained on a single main circuit board. Both
boards are mounted to a quick-removable chassis and housed
in a metal cabinet. The backbox can be installed allowing field
wiring to be pulled. When construction is completed, the chas-
sis with the electronics can be quickly installed with two bolts.
The MS-9600UDLS(E) includes a factory-installed DACT-UD2
Digital Alarm Communicator Transmitter. The DACT transmits
system status (alarm, troubles, AC loss, etc.) to a Central Sta-
tion via internet (optional IPDACT installed) or the public
switched telephone network.
Optional modules, which plug into the main circuit board, are
available for special functions. Available accessories include
LED, graphic and LCD annunciators, reverse polarity/city box
transmitter, digital alarm communicator/transmitter, SLC
expansion module, local and remote upload/download soft-
ware and remote power expansion.
FM APPROVED to UL ANSI 864.
MEMBRANE SWITCH CONTROLS
•
•
•
•
•
•
•
ACKNOWLEDGE/STEP
ALARM SILENCE
DRILL
SYSTEM RESET (lamp test)
12-key pad with full alphabet
4 cursor keys
ENTER
Special Features
•
•
•
•
•
•
•
•
•
Easy mount chassis.
7 amp switching power supply.
Large enclosure allows 18 amp-hour batteries
DACT-UD2 plug-in communicator standard with
MS-9600UDLS/E.
Optional IPDACT Internet Protocol Digital Alarm
Communicator/Transmitter
Four Style Y (Class B) or two Style Z (Class A)
NAC circuits.
Selectable strobe synchronization per NAC for
System Sensor, Wheelock, and Gentex devices.
Automated control of ACC-25/50(ZS/T) audio speaker cir-
cuits
ANN-BUS for connection to following optional modules
Note: cannot be used if ACS annunciators are used.
•ANN-80(-W) Remote LCD Annunciator
•ANN-I/O LED Driver Module
•ANN-S/PG Serial/Parallel Printer Module
•ANN-RLY Relay Module
•ANN-LED Annunciator Module
•ANN-RLED Annunciator Module (alarms only)
Controls And Indicators
LED INDICATORS
•
•
•
•
•
•
•
•
•
AC POWER (green)
FIRE ALARM (red)
SUPERVISORY (yellow)
ALARM SILENCED (yellow)
SYSTEM TROUBLE (yellow)
MAINTENANCE/PRESIGNAL (yellow)
DISABLED (yellow)
BATTERY FAULT (yellow)
GROUND FAULT (yellow)
df-60334:A1 • 03/26/2009 — Page 1 of 6
5
2
4
1
2
c
o
v
.
j
p
g
Standard Features
SLC LOOP
•SLC can be configured for NFPA Style 4, 6, or 7 operation.
•SLC supports up to 318 addressable devices per loop (159
detectors and 159 monitor, control, or relay modules).
•SLC loop maximum length 10,000 ft. (3,048 m) @ 12 AWG
(3.1 mm²) using twisted, unshielded wire (see Wire Table on
page 5).
•Optional 4XTMF module (conventional reverse polarity/city
box transmitter).
Field-programming Features
Off-line Programming: Create the entire program in your
office using a Windows®-based software package (order pro-
gramming kit PK-CD, containing PS-TOOLS, separately).
Upload/download system programming locally to the
MS-9600LS/E in less than one minute.
Autoprogramming: Command the MS-9600LS(E) to program
itself (takes less than 30 seconds). In the Auto-Program mode,
the MS-9600LS(E) scans for all possible devices at all
addresses, stores the device types, and addresses found, and
then loads default values for all options (General Alarm). It
also checks for two or more devices set to the same address.
Online Editing: While still providing fire protection, the
MS-9600LS/E may be programmed from the front panel. Sim-
ple menu trees displayed on the LCD allow the trained user to
perform all functions without referring back to the programming
manual.
English Label Library: Quickly select labels from a standard
library of more than 50 adjectives/nouns, such as “FLR 3
HALLWAY,” or enter custom labels letter-by-letter. Use recall
function to repeat previously used label.
Program Check: Automatically catch common errors, such as
control modules not linked to any zone or input point.
NOTIFICATION APPLIANCE CIRCUITS (NACS):
•Four onboard NACs with additional NAC capability using
output control modules (CMF-300 or CMF-300-6). The four
Class B NACs can be converted to two Class A NACs with
the NACKEY (included).
•Silence Inhibit and Auto Silence timer options.
•Continuous, March Time, Temporal or California code for
main circuit board NACs with two-stage capability.
•Selectable strobe synchronization per NAC.
•3.0 amps maximum per each NAC circuit
Note: Maximum 24 VDC system power output is shared
among all NAC circuits and 24 VDC special application aux-
iliary power outputs. Total available output is 7.0 amps.
ADVANCED FIRE TECHNOLOGY:
•Sensitivity testing with printable results, onsite or offsite.
•Automatic drift compensation.
PROGRAMMING AND SOFTWARE:
•Autoprogram (learn mode) reduces installation time.
•Fully programmable from local keypad, local PS/2 keyboard
or PC (using the standard PS-TOOLS Windows® utility).
•Two-level user-programmable passwords.
•Custom English labels (per point) may be manually entered
or selected from an internal library file.
•Three Form-C relay outputs (two programmable).
•99 software zones.
Maintenance Alert
The MS-9600LS(E) continuously monitors each smoke detec-
tor and is capable of reporting maintenance conditions. This
reduces the risk of false alarms due to dust accumulation.
Refer to the control panel installation manual for more informa-
tion.
Automatic Test Operation
The MS-9600LS(E) performs an automatic test of each detec-
tor every two hours. Failure to meet the test limits causes an
AUTO TEST FAIL trouble type. System Reset clears this trou-
ble.
USER INTERFACE:
•Optional plug-in DACT-UD2 communicator (standard with
MS-9600UDLS(E) with USB port for local upload/download.
•Remote Acknowledge, Silence, Reset and Drill via address-
able monitor modules, ACS Series annunciators, LCD-80F
remote annunciator, or ANN-80 Series Annunciators.
•EIA-232 printer/PC interface (variable baud rate) on main
circuit board.
•Integral 80-character LCD display with backlighting.
•Real-time clock/calendar with automatic daylight savings
adjustments.
•History file with 1,000-event capacity.
•EIA-485/ANN-BUS supporting up to 8 ANN Series Annunci-
ators or 32 ACS Series annunciators.
•EIA-485 supporting up to 32 ACS annunciators.
•Maintenance alert warns when smoke detector dust accu-
mulation is excessive.
•Automatic device type-code verification.
•One person audible or silent walk test with walk-test log and
printout.
•Point trouble identification.
•Local piezo sounder.
•Waterflow (nonsilenceable) selection per monitor point.
•System alarm verification selection per detector point.
•PAS (Positive Alarm Sequence) and presignal delay per
point (NFPA 72 compliant).
Page 2 of 6 — df-60334:A1 • 03/26/2009
Terminal Blocks
AC Power – TB1: 120 VAC, 60 Hz, 3.0 amps or 240 VAC, 50
Hz, 1.5 amps. Wire size: minimum 14 AWG (2.00 mm²) with
600 V insulation.
Battery (lead acid only) – TB2: Maximum charging circuit:
******************************.Maximumbattery
charger capacity: 26 AH. Minimum battery 12 AH. MS-
9600LS(E) cabinet holds maximum of two 18 AH batteries. For
26 – 120 AH batteries, use the CHG-120F or CHG-75 Battery
Charger and BB-55F Battery Box.
NOTE: Jumper JP3, on the FACP main circuit board, must be cut
to disable the FACP battery charger when using the CHG-120F or
CHG-75.
Communication Loop – (standard) TB8: 24 VDC nominal,
27.6 VDC maximum. Maximum length: 10,000 ft. (3048 m)
total twisted, unshielded pair length. Maximum loop current:
400 mA (short circuit) or 100 mA (normal). Maximum loop
resistance: 40 ohms. Supervised and power-limited.
Notification Appliance Circuits – TB4: Power-limited cir-
cuitry. Nominal operating voltage: 24 VDC. Current limit: fuse-
less, electronic, power-limited circuitry. Maximum signaling
current per circuit: 3.0 amps. End-of-Line Resistor: 4.7K ohm,
1/2 watt (P/N 71252 UL listed) for NACs. Refer to Fire•Lite
Device Compatibility Document for listed compatible devices.
Programmable and Trouble Output Relays – TB5: Contact
rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC
(resistive). Form-C relays.
Four-Wire Resettable Smoke Detector Power
(24 VDC nominal) – TB3, Terminals 1(+) & 2(–):
Maximum ripple voltage: 10 mV
RMS
. Up to 1.5 amps for pow-
ering four-wire smoke detectors. Power-limited circuit. Refer to
Fire•Lite Device Compatibility Document for listed compatible
devices.
Nonresettable Power #1 (24 VDC Nominal) –TB3, Termi-
nals 3 (+) & 4 (–): Maximum ripple voltage: 10 mV
RMS
. Up to
1.5 amps total DC current available from each output. Power-
limited circuit. TB3, Terminals 5 (+) & 6 (–): non-resettable
power #2.
Nonresettable Special Application Power #2 (24 VDC Nom-
inal) - TB3, Terminals 5 (+) & 6 (-): Maximum ripple voltage:
10mVRMS. Total DC current available from each output is up
to 1.5 amps. Power-limited circuit, nonsupervised.
EIA-485 (ACS/ANN) – TB6: Annunciator connector, program-
mable for type ANN or ACS. Terminal 1 (+) and Terminal 2 (–).
EIA-485 (TERM) – TB7: Terminal mode annunciator connec-
tor, Terminal 1 (Out +), 2 (In +), 3 (Out –), 4 (In –).
EIA-232 – TB8: PC/printer connector, Terminal 1 (Transmit), 2
(Receive), 3 (DTR), 4 (Ground).
BB-26: Battery backbox, holds up to two 25 AH batteries.
CHG-120F: Remote battery charging system for lead-acid bat-
teries with a rating of 25 to 120 AH. CHG-120F or CHG-75
required for charging greater than 25 AH batteries.
CHG-75: Battery charger for lead-acid batteries with a rating
of 25 to 75 AH. CHG-120F or CHG-75 required for charging
greater than 25 AH batteries.
BAT Series: Batteries, see data sheet DF-52397.
PRT/PK-CABLE: Cable printer/personal computer interface
cable.
PRN-6F: UL listed compatible event printer which uses tractor-
fed paper.
Compatible Addressable Devices
All feature a polling LED and rotary switches for addressing.
CP355: Addressable low-profile ionization smoke detector.
SD355: Addressable low-profile photoelectric smoke detector.
SD355T: Addressable low-profile photoelectric smoke detector
with thermal sensor.
H355: Fast-response, low-profile heat detector.
H355R: Fast-response, low-profile heat detector with rate-of-
rise option.
H355HT: Fast-response, low-profile heat detector that acti-
vates at190° F (88°C).
AD355: Low-profile, intelligent, “Adapt” multi-sensor detector;
B350LP base included.
BEAM355: Intelligent beam smoke detector.
BEAM355S: Intelligent beam smoke detector with integral
sensitivity test.
D350PL: Photoelectric low-flow duct smoke detector.
D350RPL: Photoelectric low-flow duct smoke detector with
relay option.
MMF-300: Addressable Monitor Module for one zone of nor-
mally-open dry-contact initiating devices. Mounts in standard
4.0" (10.16 cm.) box. Includes plastic cover plate and end-of-
line resistor. Module may be configured for either a Style B
(Class B) or Style D (Class A) IDC.
MDF-300: Dual Monitor Module. Same as MMF-300 except it
provides two Style B (Class B) only IDCs.
MMF-301: Miniature version of MMF-300. Excludes LED and
Style D option. Connects with wire pigtails. May mount in
device backbox.
MMF-302: Similar to MMF-300, but may monitor up to 20 con-
ventional two-wire detectors. Requires resettable 24 VDC
power. Consult factory for compatible smoke detectors.
CMF-300: Addressable Control Module for one Style Y/Z
(Class B/A) zone of supervised polarized Notification Appli-
ances. Mounts directly to a 4.0" (10.16 cm.) electrical box.
Notification Appliance Circuit option requires external 24 VDC
to power notification appliances.
CRF-300: Addressable relay module containing two isolated
sets of Form-C contacts, which operate as a DPDT switch.
Mounts directly to a 4.0" (10.16 cm.) box, surface mount using
the SMB500.
BG-12LX: Addressable manual pull station with interface mod-
ule mounted inside.
I300: This module isolates the SLC loop from short circuit con-
ditions (required for Style 6 or 7 operation).
SMB500: Used to mount all modules except the MMF-301 and
M301.
df-60334:A1 • 03/26/2009 — Page 3 of 6
Ordering Options
MS-9600LS(E): 318-point addressable Fire Alarm Control
Panel, one SLC loop. Includes 80-character LCD display, sin-
gle printed circuit board, and cabinet.
MS-9600UDLS(E): 318-point addressable Fire Alarm Control
Panel, one SLC loop. Includes DACT-UD2, 80-character LCD
display, single printed circuit board, and cabinet.
DACT-UD2: Optional communicator for remote monitoring
(standard with MS-9600UDLS).
4XTMF: Optional Transmitter Module provides a supervised
output for local energy municipal box transmitter, alarm and
trouble reverse polarity. It includes a disable switch and dis-
able trouble.
IPDACT-2/2UD, IPDACT Internet Monitoring Module:
Mounts in bottom of enclosure with optional mounting kit (P/N:
IPBRKT). Connects to primary and secondary DACT tele-
phone output ports for internet communications over customer
provided ethernet internet connection. Requires compatible
Teldat VisorALARM Central Station Receiver. Can use DHCP
or static IP. (See data sheet DF-60407 or DF-52424 for addi-
tional information.
IPBRKT: Optional mounting bracket kit consisting of screws
and battery shield with standoffs required when mounting the
IPDACT in lower enclosure section of FACP.
IPSPLT: Optional Y-Adaptor which allows connection of both
panel dialer outputs to one cable input to IPDACT (sold sepa-
rately).
ACM-8RF: Optional plug-in relay module provides 8 Form-C
5.0 amp relays.
PK-CD: Contains PS-TOOLS programming software for Win-
dows®-based PC computer (cable not included).
SLC-2LS: Optional expander module, enables second SLC
loop.
DP-9296: Dress panel for MS-9600LS(E) (included with unit).
TR-CE: Optional Trim Ring for semi-flush mounting.
BB-55F: Battery box, required to house two 25 AH batteries
and one CHG-120F battery charger. For batteries greater than
25 AH, consult factory for housing/mounting arrangements.
DACT-UD2
Page 4 of 6 — df-60334:A1 • 03/26/2009
MMF-300-10: Ten-input monitor module. Mount one or two
modules in a BB-2F cabinet (optional). Mount up to six mod-
ules on a CHS-6 chassis in a BB-6F.
MMF-302-6: Six-zone interface module. Mount one or two
modules in a BB-2F cabinet (optional). Mount up to six mod-
ules on a CHS-6 chassis in a BB-6F.
CMF-300-6: Six-circuit supervised control module. Mount one
or two modules in a BB-2F cabinet (optional). Mount up to six
modules on a CHS-6 chassis in a BB-6F.
CRF-300-6: Six Form-C relay control module. Mount one or
two modules in a BB-2F cabinet (optional). Mount up to six
modules on a CHS-6 chassis in a BB-6F.
Compatible Annunciators
ANN-80(-W): Remote LCD annunciator that mimics the infor-
mation displayed on the FACP’s LCD display. Recommended
wire type is unshielded. (Basic model is red; order -W version
for white; see DF-52417).
ANN-LED: Annunciator Module provides three LEDs for each
zone: Alarm, Trouble and Supervisory. Ships with red enclo-
sure (see DF-60241).
ANN-RLED: Provides alarm (red) indicators for up to 30 input
zones or addressable points (see DF-60241).
ANN-RLY: Relay Module, which can be mounted inside the
cabinet, provides 10 programmable Form-C relays (see DF-
52431).
ANN-S/PG: Serial/Parallel Printer Gateway module provides a
connection for a Serial or Parallel printer (see DF-52429).
ANN-I/O: I/O Driver Module provides connections to a user
supplied graphic annunciator (see DF-52430).
ACS-LED Zone Series: LED-type fire annunciators capable of
providing up to 99 software zones of annunciation. Available in
increments of 16 or 32 points to meet a variety of applications.
ACS-LDM Graphic Series: Lamp Driver Module series for
use with custom graphic annunciators.
TERM MODE LCD-80F (Liquid Crystal Display) point
annunciator: 80-character, backlit LCD-type fire annunciators
capable of displaying English-language text. Up to 32 LCD-
80F annunciators may be connected to the EIA-485 terminal
mode serial interface on the MS-9600LS(E) motherboard.
NOTE: For more information on Compatible Annunciators for
use with the MS-9600LS(E), see the following data sheets (docu-
ment numbers) ACM-8RF (DF-51555), ACS/ACM Series (DF-
52378), LDM Series (DF-51384), LCD-80F (DF-52185).
Wiring Requirements
While shielded wire is not required, it is recommended that all
SLC wiring be twisted-pair to minimize the effects of electrical
interference. Refer to the panel manual for wiring details.
df-60334:A1 • 03/26/2009 — Page 5 of 6
SYSTEM SPECIFICATIONS
System Capacity
•
•
•
•
•
•
•
Intelligent Signalling 1 expandable to 2
159 per loop
Addressable monitor/159 per loop
Programmable 99
8
32
32
Cabinet Specifications
Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x
0.67" (1.70 cm.) deep. Backbox: 19.00" (48.26 cm.) high x
16.65" (42.29 cm.) wide x 5.21" (13.23 cm.) deep. Trim Ring
(TR-CE): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide.
Shipping Specifications
Dimensions: 20.00” (50.80 cm) high, 22.5” (57.15 cm) wide,
8.5” (21.59 cm) deep. Weight: 27.3 lbs (12.38 kg).
Electrical Specifications
•Primary input power:
120 VAC, 50/60 Hz, 3.0 A.
240 VAC, 50 Hz, 1.5 A.
•Battery:************(max).
Maximum battery charger capacity: 26 AH.
Minimum battery: 12 AH.
MS-9600LS cabinet holds maximum of two 18 AH batteries.
•Communication Loop: 24 VDC nominal, supervised and
power-limited.
•Notification Appliance Circuits: terminal block provides con-
nections for four Style Y (Class B) or two Style Z (Class A)
NACs.
Maximum signaling current per circuit: 3.0 A.
End-of-Line Resistor: 4.7 K ohms, ½ watt (P/N 71252 UL
listed) for Style Y (Class B) NAC.
Supervised and power-limited.
Refer to panel documentation and Fire-Lite Device Compat-
ibility Document for listed compatible devices.
•Two Programmable Form-C Relays and One Fixed Trouble
Form-C Relay: Contact rating: 2.0 A @ 30 VDC (resistive)
0.5 A @ 30 VAC (resistive).
•Four-wire Resettable Special Application Power (24 VDC
nominal): Up to 1.5 A for powering four-wire smoke detec-
tors. Power-Limited, nonsupervised.
Refer to Fire-Lite Device Compatibility Document for listed
compatible devices.
•Nonresettable Special Application Power #1 (24VDC nomi-
nal) TB3, Terminals 3 (+) & 4 (-):
Maximum ripple voltage: 10 mV
RMS
Total DC current available from each output is up to 1.5 A.
Power-limited, nonsupervised.
•Nonresettable Special Application Power #2 (24VDC nomi-
nal) TB3, Terminals 5 (+) & 6 (-):
Maximum ripple voltage: 10 mV
RMS
Total DC current available from each output is up to 1.5 A.
Power-limited, nonsupervised.
NOTE: Although each Special Application power output can
deliver 1.5 A individually, the total power output from these circuits
cannot exceed 1.5 A in standby. The total Alarm output for all Spe-
cial Application power and NAC circuits cannot exceed 7 A.
Temperature and Humidity Ranges
This system meets NFPA requirements for operation at 0 –
49°C/32 – 120°F and at a relative humidity 93% ± 2% RH
(noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the
useful life of the system's standby batteries and the electronic
components may be adversely affected by extreme tempera-
ture ranges and humidity. Therefore, it is recommended that
this system and its peripherals be installed in an environment
with a normal room temperature of 15 – 27°C/60 – 80°F.
Agency Listings and Approvals
The listings and approvals below apply to the MS-9600LS(E)
and MS-9600UDLS(E) control panels. In some cases, certain
modules may not be listed by certain approval agencies, or list-
ing may be in process. Consult factory for latest listing status.
•
•
•
•
ULC: S624 (MS-9600LSC only; see DF-60438)
FM APPROVED: to UL ANSI 864
CSFM: 7170-0075:220
MEA: 87-08-E
NFPA Standards
The MS-9600LS(E) and MS-9600UDLS(E) control panels
comply with the following NFPA 72 Fire Alarm Systems
requirements:
–LOCAL (Automatic, Manual, Waterflow and Sprinkler
Supervisory).
–AUXILIARY (Automatic, Manual and Waterflow) (requires
4XTMF).
–REMOTE STATION (Automatic, Manual and Waterflow)
(Requires 4XTMF where DACT-UD2 is not accepted.)
–PROPRIETARY (Automatic, Manual and Waterflow).
–CENTRAL STATION (Automatic, Manual and Waterflow,
and Sprinkler Supervised).
–OT (Other Technologies-PSDN) For use with IPDACT.
LiteSpeed™ is a trademark; and FireLite® Alarms is a registered trademark
of Honeywell International Inc.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Fire•Lite Alarms. Phone: (800) 627-3473, FAX: (877) 699-4105.
Page 6 of 6 — df-60334:A1 • 03/26/2009
2024年9月28日发(作者：悉安翔)
df-60334:A1 • A1-100
MS-9600LS(E)/MS-9600UDLS(E)
Intelligent Addressable FACP
with Optional 2nd Loop
Addressable
General
Fire•Lite’s MS-9600LS(E) and MS-9600UDLS(E) are compact,
cost effective, intelligent addressable FACPs (Fire Alarm Con-
trol Panels) with an extensive list of powerful features. The
combination of Fire•Lite’s newer series devices and legacy
300 Series devices, along with the MS-9600LS(E) or
MS-9600UDLSE FACP, offer the latest in fire protection tech-
nology. LiteSpeed™ is a patented technology that polls 10
devices at a time looking for new or different information.
When new information is found at a specific address, the sys-
tem polls that device several times for any new data. This
improvement allows a fully loaded panel with up to 636
devices to report an incident and activate the notification cir-
cuits in under 10 seconds. With this new polling scheme,
devices can be wired on standard twisted, unshielded wire up
to a distance of 10,000 feet per loop. Each Signaling Line Cir-
cuit (SLC) loop supports up to 159 addressable detectors
including photoelectric, photoelectric with heat, beam, ioniza-
tion, photoelectric duct, fixed heat, fixed heat with rate-of-rise,
and fixed high-heat detectors. It also supports up to 159
addressable modules including monitor (two-wire detector,
normally open devices), dual-monitor functions (two monitor
circuits from one module, two addresses used), multimonitor
(multiple monitor circuits from one module, multiple addresses
used), control (for Notification Appliance Circuits), and relay
(two Form-C) modules.
The FLPS-7 power supply is a separate board while all other
electronics are contained on a single main circuit board. Both
boards are mounted to a quick-removable chassis and housed
in a metal cabinet. The backbox can be installed allowing field
wiring to be pulled. When construction is completed, the chas-
sis with the electronics can be quickly installed with two bolts.
The MS-9600UDLS(E) includes a factory-installed DACT-UD2
Digital Alarm Communicator Transmitter. The DACT transmits
system status (alarm, troubles, AC loss, etc.) to a Central Sta-
tion via internet (optional IPDACT installed) or the public
switched telephone network.
Optional modules, which plug into the main circuit board, are
available for special functions. Available accessories include
LED, graphic and LCD annunciators, reverse polarity/city box
transmitter, digital alarm communicator/transmitter, SLC
expansion module, local and remote upload/download soft-
ware and remote power expansion.
FM APPROVED to UL ANSI 864.
MEMBRANE SWITCH CONTROLS
•
•
•
•
•
•
•
ACKNOWLEDGE/STEP
ALARM SILENCE
DRILL
SYSTEM RESET (lamp test)
12-key pad with full alphabet
4 cursor keys
ENTER
Special Features
•
•
•
•
•
•
•
•
•
Easy mount chassis.
7 amp switching power supply.
Large enclosure allows 18 amp-hour batteries
DACT-UD2 plug-in communicator standard with
MS-9600UDLS/E.
Optional IPDACT Internet Protocol Digital Alarm
Communicator/Transmitter
Four Style Y (Class B) or two Style Z (Class A)
NAC circuits.
Selectable strobe synchronization per NAC for
System Sensor, Wheelock, and Gentex devices.
Automated control of ACC-25/50(ZS/T) audio speaker cir-
cuits
ANN-BUS for connection to following optional modules
Note: cannot be used if ACS annunciators are used.
•ANN-80(-W) Remote LCD Annunciator
•ANN-I/O LED Driver Module
•ANN-S/PG Serial/Parallel Printer Module
•ANN-RLY Relay Module
•ANN-LED Annunciator Module
•ANN-RLED Annunciator Module (alarms only)
Controls And Indicators
LED INDICATORS
•
•
•
•
•
•
•
•
•
AC POWER (green)
FIRE ALARM (red)
SUPERVISORY (yellow)
ALARM SILENCED (yellow)
SYSTEM TROUBLE (yellow)
MAINTENANCE/PRESIGNAL (yellow)
DISABLED (yellow)
BATTERY FAULT (yellow)
GROUND FAULT (yellow)
df-60334:A1 • 03/26/2009 — Page 1 of 6
5
2
4
1
2
c
o
v
.
j
p
g
Standard Features
SLC LOOP
•SLC can be configured for NFPA Style 4, 6, or 7 operation.
•SLC supports up to 318 addressable devices per loop (159
detectors and 159 monitor, control, or relay modules).
•SLC loop maximum length 10,000 ft. (3,048 m) @ 12 AWG
(3.1 mm²) using twisted, unshielded wire (see Wire Table on
page 5).
•Optional 4XTMF module (conventional reverse polarity/city
box transmitter).
Field-programming Features
Off-line Programming: Create the entire program in your
office using a Windows®-based software package (order pro-
gramming kit PK-CD, containing PS-TOOLS, separately).
Upload/download system programming locally to the
MS-9600LS/E in less than one minute.
Autoprogramming: Command the MS-9600LS(E) to program
itself (takes less than 30 seconds). In the Auto-Program mode,
the MS-9600LS(E) scans for all possible devices at all
addresses, stores the device types, and addresses found, and
then loads default values for all options (General Alarm). It
also checks for two or more devices set to the same address.
Online Editing: While still providing fire protection, the
MS-9600LS/E may be programmed from the front panel. Sim-
ple menu trees displayed on the LCD allow the trained user to
perform all functions without referring back to the programming
manual.
English Label Library: Quickly select labels from a standard
library of more than 50 adjectives/nouns, such as “FLR 3
HALLWAY,” or enter custom labels letter-by-letter. Use recall
function to repeat previously used label.
Program Check: Automatically catch common errors, such as
control modules not linked to any zone or input point.
NOTIFICATION APPLIANCE CIRCUITS (NACS):
•Four onboard NACs with additional NAC capability using
output control modules (CMF-300 or CMF-300-6). The four
Class B NACs can be converted to two Class A NACs with
the NACKEY (included).
•Silence Inhibit and Auto Silence timer options.
•Continuous, March Time, Temporal or California code for
main circuit board NACs with two-stage capability.
•Selectable strobe synchronization per NAC.
•3.0 amps maximum per each NAC circuit
Note: Maximum 24 VDC system power output is shared
among all NAC circuits and 24 VDC special application aux-
iliary power outputs. Total available output is 7.0 amps.
ADVANCED FIRE TECHNOLOGY:
•Sensitivity testing with printable results, onsite or offsite.
•Automatic drift compensation.
PROGRAMMING AND SOFTWARE:
•Autoprogram (learn mode) reduces installation time.
•Fully programmable from local keypad, local PS/2 keyboard
or PC (using the standard PS-TOOLS Windows® utility).
•Two-level user-programmable passwords.
•Custom English labels (per point) may be manually entered
or selected from an internal library file.
•Three Form-C relay outputs (two programmable).
•99 software zones.
Maintenance Alert
The MS-9600LS(E) continuously monitors each smoke detec-
tor and is capable of reporting maintenance conditions. This
reduces the risk of false alarms due to dust accumulation.
Refer to the control panel installation manual for more informa-
tion.
Automatic Test Operation
The MS-9600LS(E) performs an automatic test of each detec-
tor every two hours. Failure to meet the test limits causes an
AUTO TEST FAIL trouble type. System Reset clears this trou-
ble.
USER INTERFACE:
•Optional plug-in DACT-UD2 communicator (standard with
MS-9600UDLS(E) with USB port for local upload/download.
•Remote Acknowledge, Silence, Reset and Drill via address-
able monitor modules, ACS Series annunciators, LCD-80F
remote annunciator, or ANN-80 Series Annunciators.
•EIA-232 printer/PC interface (variable baud rate) on main
circuit board.
•Integral 80-character LCD display with backlighting.
•Real-time clock/calendar with automatic daylight savings
adjustments.
•History file with 1,000-event capacity.
•EIA-485/ANN-BUS supporting up to 8 ANN Series Annunci-
ators or 32 ACS Series annunciators.
•EIA-485 supporting up to 32 ACS annunciators.
•Maintenance alert warns when smoke detector dust accu-
mulation is excessive.
•Automatic device type-code verification.
•One person audible or silent walk test with walk-test log and
printout.
•Point trouble identification.
•Local piezo sounder.
•Waterflow (nonsilenceable) selection per monitor point.
•System alarm verification selection per detector point.
•PAS (Positive Alarm Sequence) and presignal delay per
point (NFPA 72 compliant).
Page 2 of 6 — df-60334:A1 • 03/26/2009
Terminal Blocks
AC Power – TB1: 120 VAC, 60 Hz, 3.0 amps or 240 VAC, 50
Hz, 1.5 amps. Wire size: minimum 14 AWG (2.00 mm²) with
600 V insulation.
Battery (lead acid only) – TB2: Maximum charging circuit:
******************************.Maximumbattery
charger capacity: 26 AH. Minimum battery 12 AH. MS-
9600LS(E) cabinet holds maximum of two 18 AH batteries. For
26 – 120 AH batteries, use the CHG-120F or CHG-75 Battery
Charger and BB-55F Battery Box.
NOTE: Jumper JP3, on the FACP main circuit board, must be cut
to disable the FACP battery charger when using the CHG-120F or
CHG-75.
Communication Loop – (standard) TB8: 24 VDC nominal,
27.6 VDC maximum. Maximum length: 10,000 ft. (3048 m)
total twisted, unshielded pair length. Maximum loop current:
400 mA (short circuit) or 100 mA (normal). Maximum loop
resistance: 40 ohms. Supervised and power-limited.
Notification Appliance Circuits – TB4: Power-limited cir-
cuitry. Nominal operating voltage: 24 VDC. Current limit: fuse-
less, electronic, power-limited circuitry. Maximum signaling
current per circuit: 3.0 amps. End-of-Line Resistor: 4.7K ohm,
1/2 watt (P/N 71252 UL listed) for NACs. Refer to Fire•Lite
Device Compatibility Document for listed compatible devices.
Programmable and Trouble Output Relays – TB5: Contact
rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC
(resistive). Form-C relays.
Four-Wire Resettable Smoke Detector Power
(24 VDC nominal) – TB3, Terminals 1(+) & 2(–):
Maximum ripple voltage: 10 mV
RMS
. Up to 1.5 amps for pow-
ering four-wire smoke detectors. Power-limited circuit. Refer to
Fire•Lite Device Compatibility Document for listed compatible
devices.
Nonresettable Power #1 (24 VDC Nominal) –TB3, Termi-
nals 3 (+) & 4 (–): Maximum ripple voltage: 10 mV
RMS
. Up to
1.5 amps total DC current available from each output. Power-
limited circuit. TB3, Terminals 5 (+) & 6 (–): non-resettable
power #2.
Nonresettable Special Application Power #2 (24 VDC Nom-
inal) - TB3, Terminals 5 (+) & 6 (-): Maximum ripple voltage:
10mVRMS. Total DC current available from each output is up
to 1.5 amps. Power-limited circuit, nonsupervised.
EIA-485 (ACS/ANN) – TB6: Annunciator connector, program-
mable for type ANN or ACS. Terminal 1 (+) and Terminal 2 (–).
EIA-485 (TERM) – TB7: Terminal mode annunciator connec-
tor, Terminal 1 (Out +), 2 (In +), 3 (Out –), 4 (In –).
EIA-232 – TB8: PC/printer connector, Terminal 1 (Transmit), 2
(Receive), 3 (DTR), 4 (Ground).
BB-26: Battery backbox, holds up to two 25 AH batteries.
CHG-120F: Remote battery charging system for lead-acid bat-
teries with a rating of 25 to 120 AH. CHG-120F or CHG-75
required for charging greater than 25 AH batteries.
CHG-75: Battery charger for lead-acid batteries with a rating
of 25 to 75 AH. CHG-120F or CHG-75 required for charging
greater than 25 AH batteries.
BAT Series: Batteries, see data sheet DF-52397.
PRT/PK-CABLE: Cable printer/personal computer interface
cable.
PRN-6F: UL listed compatible event printer which uses tractor-
fed paper.
Compatible Addressable Devices
All feature a polling LED and rotary switches for addressing.
CP355: Addressable low-profile ionization smoke detector.
SD355: Addressable low-profile photoelectric smoke detector.
SD355T: Addressable low-profile photoelectric smoke detector
with thermal sensor.
H355: Fast-response, low-profile heat detector.
H355R: Fast-response, low-profile heat detector with rate-of-
rise option.
H355HT: Fast-response, low-profile heat detector that acti-
vates at190° F (88°C).
AD355: Low-profile, intelligent, “Adapt” multi-sensor detector;
B350LP base included.
BEAM355: Intelligent beam smoke detector.
BEAM355S: Intelligent beam smoke detector with integral
sensitivity test.
D350PL: Photoelectric low-flow duct smoke detector.
D350RPL: Photoelectric low-flow duct smoke detector with
relay option.
MMF-300: Addressable Monitor Module for one zone of nor-
mally-open dry-contact initiating devices. Mounts in standard
4.0" (10.16 cm.) box. Includes plastic cover plate and end-of-
line resistor. Module may be configured for either a Style B
(Class B) or Style D (Class A) IDC.
MDF-300: Dual Monitor Module. Same as MMF-300 except it
provides two Style B (Class B) only IDCs.
MMF-301: Miniature version of MMF-300. Excludes LED and
Style D option. Connects with wire pigtails. May mount in
device backbox.
MMF-302: Similar to MMF-300, but may monitor up to 20 con-
ventional two-wire detectors. Requires resettable 24 VDC
power. Consult factory for compatible smoke detectors.
CMF-300: Addressable Control Module for one Style Y/Z
(Class B/A) zone of supervised polarized Notification Appli-
ances. Mounts directly to a 4.0" (10.16 cm.) electrical box.
Notification Appliance Circuit option requires external 24 VDC
to power notification appliances.
CRF-300: Addressable relay module containing two isolated
sets of Form-C contacts, which operate as a DPDT switch.
Mounts directly to a 4.0" (10.16 cm.) box, surface mount using
the SMB500.
BG-12LX: Addressable manual pull station with interface mod-
ule mounted inside.
I300: This module isolates the SLC loop from short circuit con-
ditions (required for Style 6 or 7 operation).
SMB500: Used to mount all modules except the MMF-301 and
M301.
df-60334:A1 • 03/26/2009 — Page 3 of 6
Ordering Options
MS-9600LS(E): 318-point addressable Fire Alarm Control
Panel, one SLC loop. Includes 80-character LCD display, sin-
gle printed circuit board, and cabinet.
MS-9600UDLS(E): 318-point addressable Fire Alarm Control
Panel, one SLC loop. Includes DACT-UD2, 80-character LCD
display, single printed circuit board, and cabinet.
DACT-UD2: Optional communicator for remote monitoring
(standard with MS-9600UDLS).
4XTMF: Optional Transmitter Module provides a supervised
output for local energy municipal box transmitter, alarm and
trouble reverse polarity. It includes a disable switch and dis-
able trouble.
IPDACT-2/2UD, IPDACT Internet Monitoring Module:
Mounts in bottom of enclosure with optional mounting kit (P/N:
IPBRKT). Connects to primary and secondary DACT tele-
phone output ports for internet communications over customer
provided ethernet internet connection. Requires compatible
Teldat VisorALARM Central Station Receiver. Can use DHCP
or static IP. (See data sheet DF-60407 or DF-52424 for addi-
tional information.
IPBRKT: Optional mounting bracket kit consisting of screws
and battery shield with standoffs required when mounting the
IPDACT in lower enclosure section of FACP.
IPSPLT: Optional Y-Adaptor which allows connection of both
panel dialer outputs to one cable input to IPDACT (sold sepa-
rately).
ACM-8RF: Optional plug-in relay module provides 8 Form-C
5.0 amp relays.
PK-CD: Contains PS-TOOLS programming software for Win-
dows®-based PC computer (cable not included).
SLC-2LS: Optional expander module, enables second SLC
loop.
DP-9296: Dress panel for MS-9600LS(E) (included with unit).
TR-CE: Optional Trim Ring for semi-flush mounting.
BB-55F: Battery box, required to house two 25 AH batteries
and one CHG-120F battery charger. For batteries greater than
25 AH, consult factory for housing/mounting arrangements.
DACT-UD2
Page 4 of 6 — df-60334:A1 • 03/26/2009
MMF-300-10: Ten-input monitor module. Mount one or two
modules in a BB-2F cabinet (optional). Mount up to six mod-
ules on a CHS-6 chassis in a BB-6F.
MMF-302-6: Six-zone interface module. Mount one or two
modules in a BB-2F cabinet (optional). Mount up to six mod-
ules on a CHS-6 chassis in a BB-6F.
CMF-300-6: Six-circuit supervised control module. Mount one
or two modules in a BB-2F cabinet (optional). Mount up to six
modules on a CHS-6 chassis in a BB-6F.
CRF-300-6: Six Form-C relay control module. Mount one or
two modules in a BB-2F cabinet (optional). Mount up to six
modules on a CHS-6 chassis in a BB-6F.
Compatible Annunciators
ANN-80(-W): Remote LCD annunciator that mimics the infor-
mation displayed on the FACP’s LCD display. Recommended
wire type is unshielded. (Basic model is red; order -W version
for white; see DF-52417).
ANN-LED: Annunciator Module provides three LEDs for each
zone: Alarm, Trouble and Supervisory. Ships with red enclo-
sure (see DF-60241).
ANN-RLED: Provides alarm (red) indicators for up to 30 input
zones or addressable points (see DF-60241).
ANN-RLY: Relay Module, which can be mounted inside the
cabinet, provides 10 programmable Form-C relays (see DF-
52431).
ANN-S/PG: Serial/Parallel Printer Gateway module provides a
connection for a Serial or Parallel printer (see DF-52429).
ANN-I/O: I/O Driver Module provides connections to a user
supplied graphic annunciator (see DF-52430).
ACS-LED Zone Series: LED-type fire annunciators capable of
providing up to 99 software zones of annunciation. Available in
increments of 16 or 32 points to meet a variety of applications.
ACS-LDM Graphic Series: Lamp Driver Module series for
use with custom graphic annunciators.
TERM MODE LCD-80F (Liquid Crystal Display) point
annunciator: 80-character, backlit LCD-type fire annunciators
capable of displaying English-language text. Up to 32 LCD-
80F annunciators may be connected to the EIA-485 terminal
mode serial interface on the MS-9600LS(E) motherboard.
NOTE: For more information on Compatible Annunciators for
use with the MS-9600LS(E), see the following data sheets (docu-
ment numbers) ACM-8RF (DF-51555), ACS/ACM Series (DF-
52378), LDM Series (DF-51384), LCD-80F (DF-52185).
Wiring Requirements
While shielded wire is not required, it is recommended that all
SLC wiring be twisted-pair to minimize the effects of electrical
interference. Refer to the panel manual for wiring details.
df-60334:A1 • 03/26/2009 — Page 5 of 6
SYSTEM SPECIFICATIONS
System Capacity
•
•
•
•
•
•
•
Intelligent Signalling 1 expandable to 2
159 per loop
Addressable monitor/159 per loop
Programmable 99
8
32
32
Cabinet Specifications
Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x
0.67" (1.70 cm.) deep. Backbox: 19.00" (48.26 cm.) high x
16.65" (42.29 cm.) wide x 5.21" (13.23 cm.) deep. Trim Ring
(TR-CE): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide.
Shipping Specifications
Dimensions: 20.00” (50.80 cm) high, 22.5” (57.15 cm) wide,
8.5” (21.59 cm) deep. Weight: 27.3 lbs (12.38 kg).
Electrical Specifications
•Primary input power:
120 VAC, 50/60 Hz, 3.0 A.
240 VAC, 50 Hz, 1.5 A.
•Battery:************(max).
Maximum battery charger capacity: 26 AH.
Minimum battery: 12 AH.
MS-9600LS cabinet holds maximum of two 18 AH batteries.
•Communication Loop: 24 VDC nominal, supervised and
power-limited.
•Notification Appliance Circuits: terminal block provides con-
nections for four Style Y (Class B) or two Style Z (Class A)
NACs.
Maximum signaling current per circuit: 3.0 A.
End-of-Line Resistor: 4.7 K ohms, ½ watt (P/N 71252 UL
listed) for Style Y (Class B) NAC.
Supervised and power-limited.
Refer to panel documentation and Fire-Lite Device Compat-
ibility Document for listed compatible devices.
•Two Programmable Form-C Relays and One Fixed Trouble
Form-C Relay: Contact rating: 2.0 A @ 30 VDC (resistive)
0.5 A @ 30 VAC (resistive).
•Four-wire Resettable Special Application Power (24 VDC
nominal): Up to 1.5 A for powering four-wire smoke detec-
tors. Power-Limited, nonsupervised.
Refer to Fire-Lite Device Compatibility Document for listed
compatible devices.
•Nonresettable Special Application Power #1 (24VDC nomi-
nal) TB3, Terminals 3 (+) & 4 (-):
Maximum ripple voltage: 10 mV
RMS
Total DC current available from each output is up to 1.5 A.
Power-limited, nonsupervised.
•Nonresettable Special Application Power #2 (24VDC nomi-
nal) TB3, Terminals 5 (+) & 6 (-):
Maximum ripple voltage: 10 mV
RMS
Total DC current available from each output is up to 1.5 A.
Power-limited, nonsupervised.
NOTE: Although each Special Application power output can
deliver 1.5 A individually, the total power output from these circuits
cannot exceed 1.5 A in standby. The total Alarm output for all Spe-
cial Application power and NAC circuits cannot exceed 7 A.
Temperature and Humidity Ranges
This system meets NFPA requirements for operation at 0 –
49°C/32 – 120°F and at a relative humidity 93% ± 2% RH
(noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the
useful life of the system's standby batteries and the electronic
components may be adversely affected by extreme tempera-
ture ranges and humidity. Therefore, it is recommended that
this system and its peripherals be installed in an environment
with a normal room temperature of 15 – 27°C/60 – 80°F.
Agency Listings and Approvals
The listings and approvals below apply to the MS-9600LS(E)
and MS-9600UDLS(E) control panels. In some cases, certain
modules may not be listed by certain approval agencies, or list-
ing may be in process. Consult factory for latest listing status.
•
•
•
•
ULC: S624 (MS-9600LSC only; see DF-60438)
FM APPROVED: to UL ANSI 864
CSFM: 7170-0075:220
MEA: 87-08-E
NFPA Standards
The MS-9600LS(E) and MS-9600UDLS(E) control panels
comply with the following NFPA 72 Fire Alarm Systems
requirements:
–LOCAL (Automatic, Manual, Waterflow and Sprinkler
Supervisory).
–AUXILIARY (Automatic, Manual and Waterflow) (requires
4XTMF).
–REMOTE STATION (Automatic, Manual and Waterflow)
(Requires 4XTMF where DACT-UD2 is not accepted.)
–PROPRIETARY (Automatic, Manual and Waterflow).
–CENTRAL STATION (Automatic, Manual and Waterflow,
and Sprinkler Supervised).
–OT (Other Technologies-PSDN) For use with IPDACT.
LiteSpeed™ is a trademark; and FireLite® Alarms is a registered trademark
of Honeywell International Inc.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Fire•Lite Alarms. Phone: (800) 627-3473, FAX: (877) 699-4105.
Page 6 of 6 — df-60334:A1 • 03/26/2009