2024年10月17日发(作者：铁凝莲)
RENTAL EQUIPMENT SETUP GUIDE
TP-Link AC1750 Router
Shipment Content:
1 x Protective Case
1 x Router
3 x Antennas
1 x Power Adapter
Quick Setup:
1. Carefully screw in the 3 antennas into the
back of the router and position them
upwards.
Skip this step for units with fixed
antennas.
2. Plug in the power adapter and a DHCP
hard line from the venue onto the router’s
WAN port (blue). Press the power button on
the back to turn on the router.
Allow 1-3
minutes for the router to light up when ready.
-
Power LED, the device is ready.
-5GHz shows that your router is broadcasting WiFi.
-2.4GHz only if your rental requires it.
-Internet “Green”, physical hardline connection established.
3. Connect your Wired devices (e.g. Ethernet
enabled Printer) Connect the Ethernet
cable to one of the LAN (1-4) ports in the
back of the router. Plug the other end of the
cable into the printer or PC.
The LAN LED on the
router lights up when connected.
Setup Video Guide:
Scan this QR code
with your phone
camera for video.
4. Connect your wireless devices (e.g.
Tablet / PC) Open the camera app on
your device and scan the QR-Code on the
bottom of the router. Alternatively use
the default SSID (Wireless Network Name)
on the bottom of the router along with
the password in your Important
Documents Folder to connect wirelessly.
5. Via WPS (e.g. WPS enabled Printer)
Press (do not hold) the WPS button on the
back of the router until the WPS LED
starts flashing. Then proceed to set the
printer on WPS mode as per its setup
document.
Allow 1-2 minutes to establish a
connection. Once the WPS changes from flashing
to solid a connection has been established.
Please DO NOT HOLD the WPS/Reset
button on the back of the router.
Contact our Support Team:
/help
+1 (800) 622-6484 Ext. 3 (USA)
+49 40 226 360 - 590 (Europe)
RENTAL EQUIPMENT SETUP GUIDE
TP-Link AC1750 Router
Troubleshooting:
What if…
… the router does not power up?
… the Internet light is Orange?
Please check if the power plugs are connected in tightly. Switch
On and Off again. Wait 3 mins.
The device is not getting an Internet connection, make sure the
hardline is plugged into the router's WAN port. Ask your venue
1) if the venue's hardline has a splash screen, your venue then
requires the routers MAC address, it can be found on the
bottom of the router 2) verify with the venue that the hardline is
DHCP not static.
No physical connection to printer or PC. Make sure the cable is
properly plugged in on both ends and the other unit is powered
up.
Please verify Caps Lock is off. Use the password provided in the
Important Documents Folder.
Your unit is pre-set to work only on the 5.0GHz wireless
connection.
… the LAN light is OFF?
… wrong/incorrect password.
… the 2.4G light is OFF?
Setup Video Guide:
Scan this QR code
with your phone
camera for video.
Contact our Support Team:
/help
+1 (800) 622-6484 Ext. 3 (USA)
+49 40 226 360 - 590 (Europe)
2024年10月17日发(作者：铁凝莲)
RENTAL EQUIPMENT SETUP GUIDE
TP-Link AC1750 Router
Shipment Content:
1 x Protective Case
1 x Router
3 x Antennas
1 x Power Adapter
Quick Setup:
1. Carefully screw in the 3 antennas into the
back of the router and position them
upwards.
Skip this step for units with fixed
antennas.
2. Plug in the power adapter and a DHCP
hard line from the venue onto the router’s
WAN port (blue). Press the power button on
the back to turn on the router.
Allow 1-3
minutes for the router to light up when ready.
-
Power LED, the device is ready.
-5GHz shows that your router is broadcasting WiFi.
-2.4GHz only if your rental requires it.
-Internet “Green”, physical hardline connection established.
3. Connect your Wired devices (e.g. Ethernet
enabled Printer) Connect the Ethernet
cable to one of the LAN (1-4) ports in the
back of the router. Plug the other end of the
cable into the printer or PC.
The LAN LED on the
router lights up when connected.
Setup Video Guide:
Scan this QR code
with your phone
camera for video.
4. Connect your wireless devices (e.g.
Tablet / PC) Open the camera app on
your device and scan the QR-Code on the
bottom of the router. Alternatively use
the default SSID (Wireless Network Name)
on the bottom of the router along with
the password in your Important
Documents Folder to connect wirelessly.
5. Via WPS (e.g. WPS enabled Printer)
Press (do not hold) the WPS button on the
back of the router until the WPS LED
starts flashing. Then proceed to set the
printer on WPS mode as per its setup
document.
Allow 1-2 minutes to establish a
connection. Once the WPS changes from flashing
to solid a connection has been established.
Please DO NOT HOLD the WPS/Reset
button on the back of the router.
Contact our Support Team:
/help
+1 (800) 622-6484 Ext. 3 (USA)
+49 40 226 360 - 590 (Europe)
RENTAL EQUIPMENT SETUP GUIDE
TP-Link AC1750 Router
Troubleshooting:
What if…
… the router does not power up?
… the Internet light is Orange?
Please check if the power plugs are connected in tightly. Switch
On and Off again. Wait 3 mins.
The device is not getting an Internet connection, make sure the
hardline is plugged into the router's WAN port. Ask your venue
1) if the venue's hardline has a splash screen, your venue then
requires the routers MAC address, it can be found on the
bottom of the router 2) verify with the venue that the hardline is
DHCP not static.
No physical connection to printer or PC. Make sure the cable is
properly plugged in on both ends and the other unit is powered
up.
Please verify Caps Lock is off. Use the password provided in the
Important Documents Folder.
Your unit is pre-set to work only on the 5.0GHz wireless
connection.
… the LAN light is OFF?
… wrong/incorrect password.
… the 2.4G light is OFF?
Setup Video Guide:
Scan this QR code
with your phone
camera for video.
Contact our Support Team:
/help
+1 (800) 622-6484 Ext. 3 (USA)
+49 40 226 360 - 590 (Europe)