2024年10月19日发(作者：百里黎明)
HP Latex 100/300/500 Printer Series
Line Sensor Cleaning
Edition 1
© Copyright 2018 HP Development Company,
L.P.
Legal notices
The information contained herein is subject to
change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be construed as
constituting an additional warranty. HP shall not
be liable for technical or editorial errors or
omissions contained herein.
Line sensor cleaning
The purpose of cleaning the line sensor is to avoid problems caused by accumulated dirt. A dirty sensor can
result in edge-detection failures during substrate loading and incorrect reading of alignment or calibration prints.
You should clean the line sensor when the following message is shown in the front panel:
Line sensor performance issue. Refer to the user guide to clean the sensor or call your HP representative if the
problem persists.
You should also clean the line sensor in any of the following cases:
●
●
●
●
●
●
●
The edge-detection procedure fails during substrate loading.
The carriage is disassembled or replaced.
Banding is detected in prints.
Misalignment between colors is detected.
Calibration of the line sensor fails.
The maintenance cartridge is not detected.
The printer is unable to read the width of the substrate.
Cleaning procedure
1.
2.
Turn off the printer and unplug the power cords.
Open the door on the right-hand side of the printer.
ENWW1
the maintenance cartridge by sliding it out.
the maintenance cartridge.
IMPORTANT:Slide it out horizontally to avoid spills, as it is full of ink.
the carriage to the right side of the printer to have appropriate access to it from underneath.
2Line sensor cleaningENWW
the sensor located on the right underside of the carriage (a flashlight is needed to see its specific
location), using a lint-free cloth or swab and, if necessary, a non-abrasive liquid such as 91% isopropyl
alcohol.
NOTE:If you are in an area (such as California) that regulates VOC cleaning and maintenance fluids,
instead of isopropyl alcohol use a VOC-certified cleaner such as properly diluted Simple Green All-Purpose
Cleaner.
7.
8.
9.
Move the carriage to the middle of the printer.
Reinsert the maintenance cartridge.
Slowly push the maintenance cartridge back into the printer.
the door on the right-hand side.
on the printer.
m a printhead alignment to verify that the line sensor is working correctly and repeat the cleaning
process if needed. If cleaning the line sensor does not yield results, call your HP representative to replace it.
ENWW3
2024年10月19日发(作者：百里黎明)
HP Latex 100/300/500 Printer Series
Line Sensor Cleaning
Edition 1
© Copyright 2018 HP Development Company,
L.P.
Legal notices
The information contained herein is subject to
change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be construed as
constituting an additional warranty. HP shall not
be liable for technical or editorial errors or
omissions contained herein.
Line sensor cleaning
The purpose of cleaning the line sensor is to avoid problems caused by accumulated dirt. A dirty sensor can
result in edge-detection failures during substrate loading and incorrect reading of alignment or calibration prints.
You should clean the line sensor when the following message is shown in the front panel:
Line sensor performance issue. Refer to the user guide to clean the sensor or call your HP representative if the
problem persists.
You should also clean the line sensor in any of the following cases:
●
●
●
●
●
●
●
The edge-detection procedure fails during substrate loading.
The carriage is disassembled or replaced.
Banding is detected in prints.
Misalignment between colors is detected.
Calibration of the line sensor fails.
The maintenance cartridge is not detected.
The printer is unable to read the width of the substrate.
Cleaning procedure
1.
2.
Turn off the printer and unplug the power cords.
Open the door on the right-hand side of the printer.
ENWW1
the maintenance cartridge by sliding it out.
the maintenance cartridge.
IMPORTANT:Slide it out horizontally to avoid spills, as it is full of ink.
the carriage to the right side of the printer to have appropriate access to it from underneath.
2Line sensor cleaningENWW
the sensor located on the right underside of the carriage (a flashlight is needed to see its specific
location), using a lint-free cloth or swab and, if necessary, a non-abrasive liquid such as 91% isopropyl
alcohol.
NOTE:If you are in an area (such as California) that regulates VOC cleaning and maintenance fluids,
instead of isopropyl alcohol use a VOC-certified cleaner such as properly diluted Simple Green All-Purpose
Cleaner.
7.
8.
9.
Move the carriage to the middle of the printer.
Reinsert the maintenance cartridge.
Slowly push the maintenance cartridge back into the printer.
the door on the right-hand side.
on the printer.
m a printhead alignment to verify that the line sensor is working correctly and repeat the cleaning
process if needed. If cleaning the line sensor does not yield results, call your HP representative to replace it.
ENWW3