2024年10月20日发(作者：慈元冬)

Samsung Component Placer CP-60L Operations Manual

8.6. Transfer In

Under the In-Line System after completing the Machine Transfer Out procedure for each

machine, this is used to load the machine file from the Off-line Programming

Workstation(OLP).

The CP-60 MMI will automatically select the default destination directory.

8.6.1. Transfer Board Program In

1. From the File menu, select the submenu, and then select .

The CP-60 MMI will display the “Transfer Board Program In“ dialog box.

Figure 8-13. “Transfer Board Program In” dialog box

2. If necessary, click the < Change Destination Directory…> button and the

Source Directory…> button to change the source directory.

3. Select the PCB program to transfer, and then click the button. Upon

completion, the CP-60 MMI will display “Complete” message on the status line of the

“Transfer Board Program In“ dialog box. Check the

UserDevicesTableTop> check box to add a new user device in the file to be imported

to the user device to the current Table Top. If the location of the existing User Device

is overlapped with that of the new User Device, an error message is produced. And if

the name of the existing User Device and that of the new User Device in the file to be

imported are the same, the system asks whether to overwrite. If the

EXISTING User Devices to UserDevicesTableTop> check box is checked, the system

overwrites without asking.

4. To close this dialog box click the button.

8-12

File Menu

8.6.2. Transfer Parts In

1. From the File menu, select the submenu, and then select .

The CP-60 MMI will display the “Transfer Parts In“ dialog box

Figure 8-14. “Transfer Parts In” dialog

2. If necessary, click the button to change the source

directory. At this time, specify the directory only. And CP-60MMI finds the

file in the specified directory and gets the part information.

3. To close this dialog box click the button.

8-13

2024年10月20日发(作者：慈元冬)

Samsung Component Placer CP-60L Operations Manual

8.6. Transfer In

Under the In-Line System after completing the Machine Transfer Out procedure for each

machine, this is used to load the machine file from the Off-line Programming

Workstation(OLP).

The CP-60 MMI will automatically select the default destination directory.

8.6.1. Transfer Board Program In

1. From the File menu, select the submenu, and then select .

The CP-60 MMI will display the “Transfer Board Program In“ dialog box.

Figure 8-13. “Transfer Board Program In” dialog box

2. If necessary, click the < Change Destination Directory…> button and the

Source Directory…> button to change the source directory.

3. Select the PCB program to transfer, and then click the button. Upon

completion, the CP-60 MMI will display “Complete” message on the status line of the

“Transfer Board Program In“ dialog box. Check the

UserDevicesTableTop> check box to add a new user device in the file to be imported

to the user device to the current Table Top. If the location of the existing User Device

is overlapped with that of the new User Device, an error message is produced. And if

the name of the existing User Device and that of the new User Device in the file to be

imported are the same, the system asks whether to overwrite. If the

EXISTING User Devices to UserDevicesTableTop> check box is checked, the system

overwrites without asking.

4. To close this dialog box click the button.

8-12

File Menu

8.6.2. Transfer Parts In

1. From the File menu, select the submenu, and then select .

The CP-60 MMI will display the “Transfer Parts In“ dialog box

Figure 8-14. “Transfer Parts In” dialog

2. If necessary, click the button to change the source

directory. At this time, specify the directory only. And CP-60MMI finds the

file in the specified directory and gets the part information.

3. To close this dialog box click the button.

8-13