peavey vsx 26e和vsx 48e数字扬声器处理器使用说明书-USB迷|专注于互联网分享

2024年10月26日发(作者：奉家欣)

VSX™26e and VSX™ 48e

Digital Loudspeaker

Processors

Operating

Manual

FCC/ICES Compliancy Statement

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, that may cause undesired operation.

Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de

brouillage, et (2) I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the

user’s authority to use the equipment.

Note – This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try and correct the

interference by one or more of the following measures.

•

Caution

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

VSX

™

26e and VSX

™

48e

Digital Loudspeaker Processors

The VSXe processors are DSP-based, loudspeaker management systems that boast a 96kHz sample rate and a floating point DSP processor for

quiet accurate filter response. The crossover filters are fully adjustable and any input can be routed to any output. The VSX® Editor Program for PC

allows complete remote setup and operation via the front panel USB port or by the rear panel Ethernet network connection. Files can also be saved

and loaded using this interface software.

This manual covers both the VSX 26e and VSX 48e DSP processors. The units are essentially identical except for the number of inputs and outputs.

Please read this guide carefully to ensure your personal safety as well as the safety of your equipment.

Features

•

Balanced Inputs: VSX 26e 2, VSX 48e 4

Balanced Outputs: VSX 26e 6, VSX 48e 8

96 kHz Sample rate

24 bit Delta-Sigma A/D and D/A converters

Dynamic range input to output greater than 109 dB (A-weighted) or 107 dB (unweighted)

Every input features Gain, Mute, HP and LP filters, 8 bands of PEQ, polarity and Delay (680 mS),

Every output features: 9 bands of PEQ, gain, compressor/limiter, polarity, Delay (680 mS), mute, and crossover/band-pass filters

EQ filter types include: PEQ, Low-Shelf, Hi-Shelf, Low-Pass, High-Pass, All-Pass1 and All-Pass2.

Crossover/Band-pass filters feature Butterworth, Bessel or Linkwitz-Riley alignments from 1st order (6 dB/Oct) to 8th order (48 dB/Oct).

Signal generator (sine, white noise, pink noise).

Channels can be linked for simplified stereo operation.

5 segment LED meters on each input

5 segment LED meters with limit indication on each output

2 XLR balanced inputs and 6 XLR balanced outputs VSXe 26

4 XLR balanced inputs and 8 XLR balanced outputs VSXe 48

Maximum input and output level +20 dBu, XLR balanced inputs and outputs.

Frequency response 20 Hz to 20 kHz +0, -1 dB

THD+N < 0.01% at 1 kHz.

Security lock

USB B port for setup and control

Ethernet port for setup and control.

Dimensions (HxWxD) 1.75" x 19" x 8" / 45mm x 480mm x 20.5mm

Weight 5.2 lbs /2.88 kg

PC Editor Programs allow complete remote setup and operation via USB or Ethernet.

NOTE: The VSX processors can be setup and operated both from the front panel and from the VSX Editor running on a PC. The

PC can be connected to the VSX via USB or Ethernet.

Front Panel

987

5432

65432

(1) USB port

The USB "B" connector is used to connect a host computer for editing and control using the VSX Editor Program.

(2) Process Function Buttons

The process-function buttons are used to select a process for editing. Lighted buttons illuminate to indicate they are available

selections. The available functions are different when an input, output or system mode (no input or output selected) for editing.

GAIN: Used to access channel gain controls

Delay: Used to access channel Delay controls

COMP: Available only for output editing, used to access channel compressor/limiter controls.

PEQ: Used to access channel equalization controls

Xover: Used to access the low-pass filter and high-pass filter controls.

POLARITY: Used to access channel polarity normal or invert controls

MATRIX: Available only for output editing, used to route inputs to outputs.

EXIT: Exit channel editing.

(3) Parameter Knob

The parameter knob is used by pressing and rotating to edit processing parameters.

(4) System Function Buttons

Utility: Utility functions include setting Unit ID#, IP address, Security Lock and password, input signal or signal generator,

copy channel and Delay units.

Recall: Used to load saved system presets.

Save: Used to save system presets.

(5) LCD Display

Used in conjunction with the front panel controls to edit processing parameters.

(6) Output Mute Buttons

Pressing the mute button alternately mutes and un-mutes the corresponding output. The button lights red when muted.

(7) Output Edit Buttons

Press this button to begin editing processes for the selected output. The specific process to edit can be selected using the process-function

buttons on the right.

(8) Input/Output Monitoring:

Input: The 5 segment LED meters indicate the input signal level with the top Clip LED illuminating before the onset of

clipping. Although you will want to avoid clipping, you will achieve best performance if the 0 LED lights frequently during

loud passages.

Output: The top LED illuminates to indicate the signal has reached the threshold set in the compressor/limiter and that gain

reduction is occurring. The bottom 4 LEDs form the output level meters indicating signal level. The Clip LED illuminates

before the onset of clipping. Although you will want to avoid clipping, you will achieve best performance if the 0 LED flashes

frequently during loud passages.

(9) Input Edit Buttons

Press this button to begin editing processes for the selected input. The specific process to edit can be selected using the process-function

buttons on the right.

(10) Input Mute Buttons

Pressing the mute button alternately mutes and un-mutes the corresponding input. The button lights red when muted.

Rear Panel

12131516

1112131516

(

11) IEC POWER CORD CONNECTION and Fuse Holder

This receptacle is for the IEC line cord (supplied) that provides AC power to the unit. It is very important that you ensure the unit

has the proper AC line voltage supplied.

Please read this guide carefully to ensure your personal safety as well as the safety of your equipment. Never break off the ground pin

on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should

be used and the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always be sure that the mixer

and all other associated equipment are properly grounded.

Caution: For 195 to 240 VAC operation, a “F2AL 250V” fuse rated at 2 amps should be used.

(12) ON-OFF SWITCH

This rocker switch supplies AC power to the unit when switched to the ON position. The ON position is with the top side of the

switch pushed “in” or nearly flush with the rear panel.

(13) Ethernet Control Interface

Ethernet port for control of the VSX using the graphical user interface.

(14) D sub 9 connector

Connection for RS232 and RS485 serial control.

(15) OUTPUTS

XLR balanced outputs 1-6 or 1-8.

(16) INPUTS

XLR balanced inputs A and B or A, B, C and C.

Operation

Operating the VSX processors from the front panel is made simple by a wide array of buttons and a simple

intuitive interface.

Opening screen shows product name and firmware version.

After a brief time out, the currently active preset is displayed.

Global Functions: Utility, Recall and Save

Pressing the utility button opens the screens for system wide settings. Each press of the utility button advances

to the next screen in the sequence. You can press the "Exit" button at any time to return to the main screen.

Device ID #: (Utility Button)

The ID number of the unit can be set in this screen. The ID is used with the Editor program to identify this

unit when multiple units are connected. Each unit must have a unique identifier. It is most important when

units are connected together using the RS 485 serial interface. See the section on serial communication for

more details.

Ethernet Address: (Utility Button)

Set the Ethernet, IP address here for connection to the Editor program using the Ethernet port. Make sure to

note the new address if you edit address!

Security Lock: (Utility Button)

Once on this screen, the parameter knob is used to set the password. Press to advance and rotate to change

each digit. A "Y" or "N" will appear allowing to engage the lock "Y" or turn it off "N".

Input Source Select: (Utility Button)

During normal operation, the analog inputs on the rear of the VSX are routed to the outputs. However, the

VSX has an internal signal generator that can be used for setup and testing. Rotating the parameter knob allows

you to select Analog Input, Pink Noise, White Noise or a Sine-Wave as the input source for all inputs. The

new selection will blink on the screen. Press the Parameter knob to select. You may wish to mute outputs that

you do not wish to receive the signal from the generator. Analog input must be selected for those inputs to

function.

Copy Settings: (Utility Button)

Settings can easily be copied from one input channel to another input or from one output to another. Rotate

the parameter encoder to select the parameter.

Delay Units: (Utility Button)

The units used to set delays can be selected on this screen. The options are milli-Seconds (mS), meters (m) or

feet (ft)

Load: (Recall Button)

Rotate the Parameter knob to select the desired preset number then press to load.

Save: (Save Button)

Select the desired user storage location using the parameter knob then Press. Enter a name for the preset and

then press the parameter knob again when the "Y" appears to complete the save.

Input/Output Parameters

The next section of controls are used to make adjustments to a particular input or output.

Begin by pressing the "EDIT" button (7 and 9) for the channel you wish to adjust. The edit function buttons at

the right side of the front panel that apply to the channel selection will light. The function selected will blink.

Input Edit functions: Gain, PEQ, Link, Delay, X-Over and Polarity.

Output Edit functions: Gain, PEQ, Link, Delay, X-Over, Matrix, Comp and Polarity.

While editing, you can select another function or another channel by pressing the appropriate button.

Press Exit to return to the main screen.

Gain

The input and output gain can be adjusted in a range of -60 dB to +12 dB in 0.1 dB increments. For best oper-

ation, the gain should not be set at extreme settings (0dB is optimal). It is always best to adjust the signal level

driving the VSX input so that the Yellow LED lights on louder signals. When using the crossover on an output,

you may need to increase the gain to achieve sufficient signal level to drive the amplifier. If you find that you

need to turn down an output very far below 0 dB, you will get quieter operation if you reduce the amplifier input

level control instead.

PEQ

The input channels have 8 bands of equalization available and the outputs have 9. The EQ band is indicated in

the upper left corner of the display. (Band 1 is shown above) The parameter selected for adjustment will blink

on the screen. Press the parameter knob to select a parameter for editing. Rotate the knob to adjust.

F= Frequency, Q is inverse of Bandwidth. High Q equates to narrow bandwidth. G= Gain.

The EQ types available are: Peak/Dip (PEAK), Low-Shelf (L-SHLF), High-Shelf (H_SHLF), Low-Pass (L-PASS),

High-Pass (H-PASS), All-Pass 1 (A-PAS1), All-Pass 2 (A-PAS2)

"On" is active and "By"= Bypass.

Link

Many times, in particular for stereo signals, you may want to make the same adjust to two or more channels at

the same time. Using the link function, inputs can be linked to other inputs and outputs can be linked to other

outputs. The check marks on the above screen indicate linkage. When channels are linked, the edit buttons for

those channels will blink simultaneously when editing.

Delay

Up to 680 milli-Seconds of delay can be added to any input or output. The delay resolution is 1 sample or 10.4

micro-Seconds.

Crossover (X-Over)

Although the button is labeled X-OVER and that is how these functions are often used, each input and output

have very flexible high-pass and low-pass filters that can be configured for many applications.

To activate the filter use the parameter control to select bypass on the screen and change it to the desired filter

type. There are 3 different filter alignments available, Butterworth, Bessel and Linkwitz-Riley. The filter slopes of

6 dB/Octave to 48 dB/Octave can be selected.

Matrix

The Matrix screen is only available when editing an output. This is where the inputs that drive each output are

connected. The above screen shows input "A" as the signal source for output 1. If multiple inputs are selected,

their signals are summed.

Compressor (COMP)

The compressor screen is only available when editing an output. The compressor parameters are: T= Threshold,

R= Ratio, AT= Attack Time and RT= Release Time. The threshold is roughly equal to the limiting level in dBu.

The limit LED corresponding to the output channel will light when the threshold is exceeded. The status is also

displayed in the computer editor.

Polarity

0= Normal polarity. 180= Reverse polarity.

VSX™ Editor Program

The VSX processors can be setup and controlled using the VSX Editor which runs on a Windows computer. To

control the VSX, the computer can be connected to the VSX via USB, Ethernet, RS-232 or RS-485. For most

applications, USB or Ethernet will be the preferred solutions.

Connect the computer to the VSX using a USB cable connected to USB jack on the front of the unit.

When connected to the editor, front panel controls are locked out.

Connecting a computer to the VSX via Ethernet.

The VSX processors use a "Static" IP address. Setting the address of the unit and ID# is described in the utility

section of the manual. The Editor must be set the matching IP address and ID# in order to connect.

An Ethernet cable can be connected directly to most computers if only one unit is being controlled. In most

cases you will want to use an Ethernet router or WiFi router.

If the computer is connected before launching the VSX editor software, the software will search for connected

devices. If it does not connect, check to be sure the IP address and device ID# of the unit match the settings in

the editor. Also, make sure the VSX IP address is set in the network range of your computer and router. You can

then click scan or click the offline Icon in the upper right corner of the screen to scan and connect.

Once connected, the setting from the unit will be loaded and the icon will turn green and indicate online. Use

the Tabs at the top of the screen to navigate to the desired screen.

Gain Screen

The gain screen above gives a good overview of the system. In addition to showing input and output gains, mute

and polarity status, Input and output equalization curves can be displayed.

Compressor Screen

The Compressor screen displays the settings of all 8 output compressors along with signal level, and limit status.

The transfer function of a selected output is also displayed.

Delay Screen

All of the input and output delays are shown in the above screen. Delays can be adjusted using the sliders at the

bottom, by sliding the speakers at the top or by direct typed entry. To directly enter the delay time, double click

the delay time and type a new value. If you hold down the left mouse button on a slider, you can fine adjust the

delay by using the up and down arrow buttons on the keyboard.

The delay display units can be selected on the right.

Matrix Screen

The input sources for each output are routed on the Matrix screen. Click the input button below the output to

select. If more than one source is selected those inputs will sum. A graphical representation of the routing is

given at the top. Inputs and outputs can also be labeled in this screen.

Input Eqaulization Edit Screen

The input equalization can be adjusted using this screen. When you select a PEQ band # at the bottom left of the

screen, the parameters for that band can be adjusted using the PEQ Parameter sliders. A PEQ band can also be

adjusted by selecting the corresponding band on the graph with the mouse and dragging it to set frequency and

amplitude. While holding mouse button down, the Q can be adjusted using the + and - keys. If you double click

on a parameter in the PEQ matrix, you can directly type in a new value. The graph can display either the mag-

nitude of filter responses or the resulting phase response. The graph of other inputs can also be overlaid on the

screen by clicking boxes on top of the graph.

Output Equalization Edit Screen

The output equalization can be adjusted using this screen. When you select a PEQ band # at the bottom left of

the screen, the parameters for that band can be adjusted using the PEQ Parameter sliders. A PEQ band can also

be adjusted by selecting the corresponding band on the graph with the mouse and dragging it to set frequency

and amplitude. While holding mouse button down, the Q can be adjusted using the + and - keys. If you double

click on a parameter in the PEQ matrix, you can directly type in a new value. The graph can display either the

magnitude of filter responses or the resulting phase response. The graph of other outputs can also be overlaid on

the screen by clicking boxes on top of the graph.

File Management

Store (1)

The store button at the bottom of the screen duplicates the store button on the front panel of the VSX. The user

can select one of 30 user storage locations to save the current settings.

Recall (2)

The Recall button at the bottom of the screen duplicates the Recall button on the front panel of the VSX. The

user can Recall one of 30 user stored presets.

File > Open

Open a saved *.prs "preset" file. If you wish to open a preset (*.prs) file and load it into the VSX, you must be

connected and "Online" when you open the file. If the VSX is "offline" it will load only into the editor program.

If you then connect the editor to the VSX going 'Online", the VSX settings will be loaded into the editor over-

writing the editor settings.

File >Save

Save the current settings in the editor into a *.prs "preset" file.

File >Upload

This uploads all of the presets from the VSX and saves them to a *.unt "unit file.

File >Download

This loads a *.unt file containing all of the unit presets into the connected unit. The VSX will be "offline" when

complete.

Specifications

Input Impedance:

20 k Ohms

100 OhmsOutput Impedance:

Frequency response Input to Output: +0/ -0.5 dB 10 Hz to 21 kHz

+0/ -1.0 dB 10 Hz to 32 kHz

+20 dBu

0.007%

-87 dBu unweighted -89 dB A-Weighted

107 dB unweighted 109 dB A-Weighted.

Less than -100 dB at 1 kHz.

Maximum Input level:

Maximum Output level:

THD + N @ 1 kHz:

Noise floor 22-22kHz

Dynamic range >

Crosstalk between channels:

LED Meter Input:

LED Color Label

Red Clip

dBu *

+15

dBFS *

-5

Yellow +5 +5 -15

Green 0 0 -20

Green -10 -10 -30

Green -30 -30 -50

LED Meter Output:

LED Color Label

Amber

Red

dBu * dBFS *

-5

Limit -

Clip +15

Green 0 0 -20

Green -10 -10 -30

Green -30 -30 -50

*Note References:

Latency analog input to analog output: 3.5 mS

0 dBFS = Maximum signal level before clipping (Full Scale)

0 dBu = 0.775 V rms

Sample Rate:

Ethernet Interface:

96 kHz

10.0 Mbps

Static IPv4 address

RS 232 and RS 485: Baud Rate: 115200

Data bits: 8

Parity: None

Stop bits: 1

RS 232/485 Pinout:

RS 232 RX:

RS 232 TX:

RS 232 GND:

RS 485 +:

RS 485 -:

Pin 2

Pin 3

Pin 5

Pin 7

Pin 8

Dimensions:

1.75 x 19 x 8.25 inches H x W x D

44.5 x 482 x 210 mm

5.28 pounds 2.39 kg

195 to 240 VAC 50-60 Hz

15 Watts

F2AL 250V (5x20mm)

Net Weight:

AC power Input Voltage

Power Consumption

Fuse

RS 232, RS 485 message formats are available in the VSX editor help files.