2024年11月3日发(作者：澹台清霁)
111-38-URM-011
KDS USB FW Update
User Manual
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. All other
product and brand names are trademarks and/or registered trademarks of their respective companies. Epson disclaims any and all
rights in these marks. Copyright 2022 Seiko Epson Corporation.
KDS USB FW Update
User Manual
Page 1 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
Table of Contents
1. Introduction ................................................................................................................... 3
2. Process under Microsoft Windows ............................................................................ 4
2.1. How to create Epson KDS firmware update USB stick ....................................................................... 4
2.2. How to update each printer/display box .............................................................................................. 5
3.1. How to create Epson KDS firmware update USB stick ....................................................................... 6
3.2. How to update each printer/display box .............................................................................................. 7
3. Process under Mac OS ................................................................................................ 6
KDS USB FW Update
User Manual
Page 2 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
1. Introduction
The Epson Kitchen Display System (henceforth KDS) is preferably updated using the KDS Utility. However,
an alternate update method using a USB flash drive can be employed as fallback if required, and is typically
faster than with the KDS Utility, albeit at the cost of losing any configuration from the KDS device. This
document describes the typical process to set up a USB flash drive for the firmware update.
The same firmware update process is used for printers and controllers (henceforth called display box). Once
set up, the USB flash drive can be used to sequentially update multiple devices.
IMPORTANT NOTES:
i. Before you proceed, note that updating the KDS using this method erases all
configuration from the target device(s). The KDS Utility may be used to re-configure the system.
ii. Make sure any USB flash drive used in this procedure is not faulty or corrupted, and
does NOT contain any sensitive or important data. All data on the device will be lost !!
KDS USB FW Update
User Manual
Page 3 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
2. Process under Microsoft Windows
The following process has been verified under Microsoft Windows 7 and Windows 10. Most failures with the
method can be attributed to user permissions (inability to modify USB flash drive) or to corrupted USB flash
drives.
2.1. How to create Epson KDS firmware update USB stick
1. Get a USB flash drive of 1GB or more with no contents you care about, as everything on it will be
erased.
2. Download this application (balenaEtcher-Portable) on your Windows PC:
/balena-io/etcher/releases/download/v1.5.120/
3. Plug the USB flash drive into a Windows PC.
4. Run .
5. Click on “Flash from file”.
6. At the bottom right of the balenaEtcher window, please change file type to “All (*.*)”.
7. Browse to the location of our released image folder, and select the file: usb_boot_image_ .
Click on “Open”.
8. Next, make sure the your target USB flash drive is selected (if not, use the “Change” button to select
the right one).
KDS USB FW Update
User Manual
Page 4 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
9. Click on “Flash!” to start creating the new USB drive. Allow balenaEtcher to completely validate the
USB drive; it will alert you when finished.
10. Unplug your USB drive, wait 5 seconds, plug it back in.
11. Extract “KDS ” onto the USB stick. This means the final layout for the USB stick should
be:
o
▪
▪
▪
▪
autooperation
uImage
images
•
• hibdrv
• hibernation
• hibernationinfo
• rootfs
• uImage
• writable-region
12. Safely eject the USB stick from the PC again.
13. Label the USB stick with ‘KDS Image ver ’ to indicate what image is on it, in case it is required
for other printers/controllers in the future.
2.2. How to update each printer/display box
1.
With the printer/display box turned off, plug the USB stick into the Interface card at the back.
2.
Use a pen or paper clip to press in the button on the back of the printer/display box, and hold it
pressed while turning the device on. Keep holding the button down for three or four seconds until the
amber LED at the back goes out.
3.
The back LED light will then show amber for about 45 seconds, followed by green for about 5
seconds, and then flash amber for about 60 seconds. Upon completion of the firmware update
procedure, the back LED starts blinking green. IT IS IMPORTANT TO WAIT FOR THE BLINKING
GREEN LED BEFORE PROCEEDING.
4.
Turn off the printer/display box.
5.
Remove the USB stick from the printer/display box.
6.
Turn the printer/display box back on and wait for it to boot up, and for the back LED to turn green.
The splash screen should show the newly installed KDS firmware version on the attached monitor.
KDS USB FW Update
User Manual
Page 5 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
3. Process under Mac OS
The following process has been verified under Mac OS 10 and 11. Most failures with the method can be
attributed to user permissions (inability to modify USB flash drive) incompatible or corrupted USB flash
drives.
3.1. How to create Epson KDS firmware update USB stick
1. Save the firmware update package (which includes the file usb_boot_image_) in the Desktop
or Downloads folder.
2. Get a USB flash drive of 1GB or more with no contents you care about, as everything on it will be
erased. Do NOT plug it in yet.
3. On the Mac, open a new terminal (iTerm).
4. Type the command “diskutil list” to get the current list of devices.
5. Now plug the USB flash drive into the Mac.
6. Type the command “diskutil list” again and note the additional device, which is the USB flash
drive (e.g. /dev/disk2).
7. Type the command “diskutil unmountDisk /dev/diskX”, where X is the number from Step 5.
8. Type the following command:
sudo dd if=”$(find ~ -name usb_boot_image_ | head -n 1)” of=/dev/diskX
bs=1m
(again, substitute the X in the command with the number you learned from Step 5.)
Please note:
i. The command above will ask for the user (or administrator) password once; this is normal.
ii. The command, when run for the first time, will trigger several pop-up dialogs requesting access
to some folders. See Figure 3.1.
iii. The command will output several lines with the text “Operation not permitted” when trying to
search certain inaccessible folders; this is normal.
Figure 3.1: Mac OS pop-ups requesting user permission to access some folders.
(continued…)
KDS USB FW Update
User Manual
Page 6 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
9. ***IMPORTANT*** Safely eject the USB stick from the Mac, then unplug it, wait a few
seconds, then plug it back in again.
10. Unzip the KDS file into USB stick. This means the final layout for the USB stick should be:
|- autooperation
|- uImage
|-
|- images
|--
|-- hibdrv
|-- hibernation
|-- hibernationinfo
|-- rootfs
|-- uImage
|-- writable-region
11. Eject the USB stick from the Mac again.
12. Label the USB stick with ‘KDS Image’ to indicate what image is on it in case it is required for other
display boxes/printers or in future.
3.2. How to update each printer/display box
1.
With the printer/display box turned off, plug the USB stick into the Interface card at the back.
2.
Use a pen or paper clip to press in the button on the back of the printer/display box, and hold it
pressed while turning the device on. Keep holding the button down for three or four seconds until the
amber LED at the back goes out.
3.
The back LED light will then show amber for about 45 seconds, followed by green for about 5
seconds, and then flash amber for about 60 seconds. Upon completion of the firmware update
procedure, the back LED starts blinking green. IT IS IMPORTANT TO WAIT FOR THE BLINKING
GREEN LED BEFORE PROCEEDING.
4.
Turn off the printer/display box.
5.
Remove the USB stick from the printer/display box.
6.
Turn the printer/display box back on and wait for it to boot up, and for the back LED to turn green.
The splash screen should show the newly installed KDS firmware version on the attached monitor.
KDS USB FW Update
User Manual
Page 7 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
2024年11月3日发(作者：澹台清霁)
111-38-URM-011
KDS USB FW Update
User Manual
EPSON is a registered trademark and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. All other
product and brand names are trademarks and/or registered trademarks of their respective companies. Epson disclaims any and all
rights in these marks. Copyright 2022 Seiko Epson Corporation.
KDS USB FW Update
User Manual
Page 1 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
Table of Contents
1. Introduction ................................................................................................................... 3
2. Process under Microsoft Windows ............................................................................ 4
2.1. How to create Epson KDS firmware update USB stick ....................................................................... 4
2.2. How to update each printer/display box .............................................................................................. 5
3.1. How to create Epson KDS firmware update USB stick ....................................................................... 6
3.2. How to update each printer/display box .............................................................................................. 7
3. Process under Mac OS ................................................................................................ 6
KDS USB FW Update
User Manual
Page 2 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
1. Introduction
The Epson Kitchen Display System (henceforth KDS) is preferably updated using the KDS Utility. However,
an alternate update method using a USB flash drive can be employed as fallback if required, and is typically
faster than with the KDS Utility, albeit at the cost of losing any configuration from the KDS device. This
document describes the typical process to set up a USB flash drive for the firmware update.
The same firmware update process is used for printers and controllers (henceforth called display box). Once
set up, the USB flash drive can be used to sequentially update multiple devices.
IMPORTANT NOTES:
i. Before you proceed, note that updating the KDS using this method erases all
configuration from the target device(s). The KDS Utility may be used to re-configure the system.
ii. Make sure any USB flash drive used in this procedure is not faulty or corrupted, and
does NOT contain any sensitive or important data. All data on the device will be lost !!
KDS USB FW Update
User Manual
Page 3 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
2. Process under Microsoft Windows
The following process has been verified under Microsoft Windows 7 and Windows 10. Most failures with the
method can be attributed to user permissions (inability to modify USB flash drive) or to corrupted USB flash
drives.
2.1. How to create Epson KDS firmware update USB stick
1. Get a USB flash drive of 1GB or more with no contents you care about, as everything on it will be
erased.
2. Download this application (balenaEtcher-Portable) on your Windows PC:
/balena-io/etcher/releases/download/v1.5.120/
3. Plug the USB flash drive into a Windows PC.
4. Run .
5. Click on “Flash from file”.
6. At the bottom right of the balenaEtcher window, please change file type to “All (*.*)”.
7. Browse to the location of our released image folder, and select the file: usb_boot_image_ .
Click on “Open”.
8. Next, make sure the your target USB flash drive is selected (if not, use the “Change” button to select
the right one).
KDS USB FW Update
User Manual
Page 4 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
9. Click on “Flash!” to start creating the new USB drive. Allow balenaEtcher to completely validate the
USB drive; it will alert you when finished.
10. Unplug your USB drive, wait 5 seconds, plug it back in.
11. Extract “KDS ” onto the USB stick. This means the final layout for the USB stick should
be:
o
▪
▪
▪
▪
autooperation
uImage
images
•
• hibdrv
• hibernation
• hibernationinfo
• rootfs
• uImage
• writable-region
12. Safely eject the USB stick from the PC again.
13. Label the USB stick with ‘KDS Image ver ’ to indicate what image is on it, in case it is required
for other printers/controllers in the future.
2.2. How to update each printer/display box
1.
With the printer/display box turned off, plug the USB stick into the Interface card at the back.
2.
Use a pen or paper clip to press in the button on the back of the printer/display box, and hold it
pressed while turning the device on. Keep holding the button down for three or four seconds until the
amber LED at the back goes out.
3.
The back LED light will then show amber for about 45 seconds, followed by green for about 5
seconds, and then flash amber for about 60 seconds. Upon completion of the firmware update
procedure, the back LED starts blinking green. IT IS IMPORTANT TO WAIT FOR THE BLINKING
GREEN LED BEFORE PROCEEDING.
4.
Turn off the printer/display box.
5.
Remove the USB stick from the printer/display box.
6.
Turn the printer/display box back on and wait for it to boot up, and for the back LED to turn green.
The splash screen should show the newly installed KDS firmware version on the attached monitor.
KDS USB FW Update
User Manual
Page 5 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
3. Process under Mac OS
The following process has been verified under Mac OS 10 and 11. Most failures with the method can be
attributed to user permissions (inability to modify USB flash drive) incompatible or corrupted USB flash
drives.
3.1. How to create Epson KDS firmware update USB stick
1. Save the firmware update package (which includes the file usb_boot_image_) in the Desktop
or Downloads folder.
2. Get a USB flash drive of 1GB or more with no contents you care about, as everything on it will be
erased. Do NOT plug it in yet.
3. On the Mac, open a new terminal (iTerm).
4. Type the command “diskutil list” to get the current list of devices.
5. Now plug the USB flash drive into the Mac.
6. Type the command “diskutil list” again and note the additional device, which is the USB flash
drive (e.g. /dev/disk2).
7. Type the command “diskutil unmountDisk /dev/diskX”, where X is the number from Step 5.
8. Type the following command:
sudo dd if=”$(find ~ -name usb_boot_image_ | head -n 1)” of=/dev/diskX
bs=1m
(again, substitute the X in the command with the number you learned from Step 5.)
Please note:
i. The command above will ask for the user (or administrator) password once; this is normal.
ii. The command, when run for the first time, will trigger several pop-up dialogs requesting access
to some folders. See Figure 3.1.
iii. The command will output several lines with the text “Operation not permitted” when trying to
search certain inaccessible folders; this is normal.
Figure 3.1: Mac OS pop-ups requesting user permission to access some folders.
(continued…)
KDS USB FW Update
User Manual
Page 6 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00
9. ***IMPORTANT*** Safely eject the USB stick from the Mac, then unplug it, wait a few
seconds, then plug it back in again.
10. Unzip the KDS file into USB stick. This means the final layout for the USB stick should be:
|- autooperation
|- uImage
|-
|- images
|--
|-- hibdrv
|-- hibernation
|-- hibernationinfo
|-- rootfs
|-- uImage
|-- writable-region
11. Eject the USB stick from the Mac again.
12. Label the USB stick with ‘KDS Image’ to indicate what image is on it in case it is required for other
display boxes/printers or in future.
3.2. How to update each printer/display box
1.
With the printer/display box turned off, plug the USB stick into the Interface card at the back.
2.
Use a pen or paper clip to press in the button on the back of the printer/display box, and hold it
pressed while turning the device on. Keep holding the button down for three or four seconds until the
amber LED at the back goes out.
3.
The back LED light will then show amber for about 45 seconds, followed by green for about 5
seconds, and then flash amber for about 60 seconds. Upon completion of the firmware update
procedure, the back LED starts blinking green. IT IS IMPORTANT TO WAIT FOR THE BLINKING
GREEN LED BEFORE PROCEEDING.
4.
Turn off the printer/display box.
5.
Remove the USB stick from the printer/display box.
6.
Turn the printer/display box back on and wait for it to boot up, and for the back LED to turn green.
The splash screen should show the newly installed KDS firmware version on the attached monitor.
KDS USB FW Update
User Manual
Page 7 of 7
111-38-URM-011
R2.50
Form: F-730-028 v1.00