NVIDIA Maxwell DA-07173-001_v8.0 应用优化指南说明书-USB迷|专注于互联网分享

2024年11月5日发(作者：零雁凡)

TUNING CUDA APPLICATIONS FOR

MAXWELL

DA-07173-001_v8.0 | June 2017

Application Note

TABLE OF CONTENTS

Chapter 1. Maxwell 1

1.1. NVIDIA Maxwell 1

1.2. CUDA .2

1.3. .2

1.4. 2

1.4.1. .2

1.4.1.1. 2

1.4.1.2. 3

1.4.1.3. 3

1.4.1.4. .3

1.4.2. 4

1.4.2.1. Unified L1/4

1.4.3. .4

1.4.3.1. Shared 4

1.4.3.2. Shared 5

1.4.3.3. Fast Shared 5

1.4.4. 6

Appendix A. 7

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | ii

1.1. NVIDIA Maxwell Compute Architecture

Maxwell is NVIDIA's next-generation architecture for CUDA compute applications.

Maxwell retains and extends the same CUDA programming model as in previous

NVIDIA architectures such as Fermi and Kepler, and applications that follow the

best practices for those architectures should typically see speedups on the Maxwell

architecture without any code changes. This guide summarizes the ways that an

application can be fine-tuned to gain additional speedups by leveraging Maxwell

architectural features.

Maxwell introduces an all-new design for the Streaming Multiprocessor (SM) that

dramatically improves energy efficiency. Although the Kepler SMX design was

extremely efficient for its generation, through its development, NVIDIA's GPU architects

saw an opportunity for another big leap forward in architectural efficiency; the Maxwell

SM is the realization of that vision. Improvements to control logic partitioning, workload

balancing, clock-gating granularity, compiler-based scheduling, number of instructions

issued per clock cycle, and many other enhancements allow the Maxwell SM (also called

SMM) to far exceed Kepler SMX efficiency.

The first Maxwell-based GPU is codenamed GM107 and is designed for use in power-

limited environments like notebooks and small form factor (SFF) PCs. GM107 is

described in a whitepaper entitled NVIDIA GeForce GTX 750 Ti: Featuring First-

Generation Maxwell GPU Technology, Designed for Extreme Performance per Watt.

The first GPU using the second-generation Maxwell architecture is codenamed GM204.

Second-generation Maxwell GPUs retain the power efficiency of the earlier generation

while delivering significantly higher performance. GM204 is described in a whitepaper

entitled NVIDIA GeForce GTX 980: Featuring Maxwell, The Most Advanced GPU Ever Made.

Throughout this guide, Fermi refers to devices of compute capability 2.x, Kepler refers to devices of compute capability

3.x, and Maxwell refers to devices of compute

The features of GM108 are similar to those of GM107.

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 1

Maxwell Tuning Guide

Compute programming features of GM204 are similar to those of GM107, except where

explicitly noted in this guide. For details on the programming features discussed in this

guide, please refer to the CUDA C Programming Guide.

1.2. CUDA Best Practices

The performance guidelines and best practices described in the CUDA C Programming

Guide and the CUDA C Best Practices Guide apply to all CUDA-capable GPU

architectures. Programmers must primarily focus on following those recommendations

to achieve the best performance.

The high-priority recommendations from those guides are as follows:

‣

Find ways to parallelize sequential code,

Minimize data transfers between the host and the device,

Adjust kernel launch configuration to maximize device utilization,

Ensure global memory accesses are coalesced,

Minimize redundant accesses to global memory whenever possible,

Avoid long sequences of diverged execution by threads within the same warp.

1.3. Application Compatibility

Before addressing specific performance tuning issues covered in this guide, refer to the

Maxwell Compatibility Guide for CUDA Applications to ensure that your application is

compiled in a way that is compatible with Maxwell.

1.4. Maxwell Tuning

1.4.1. SMM

The Maxwell Streaming Multiprocessor, SMM, is similar in many respects to the Kepler

architecture's SMX. The key enhancements of SMM over SMX are geared toward

improving efficiency without requiring significant increases in available parallelism per

SM from the application.

1.4.1.1. Occupancy

The maximum number of concurrent warps per SMM remains the same as in SMX (i.e.,

64), and factors influencing warp occupancy remain similar or improved over SMX:

‣

The register file size (64k 32-bit registers) is the same as that of SMX.

The maximum registers per thread, 255, matches that of Kepler GK110. As with

Kepler, experimentation should be used to determine the optimum balance of

The maximum number of thread blocks per SM has been increased from 16 to 32.

This should result in an automatic occupancy improvement for kernels with small

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 2

Maxwell Tuning Guide

‣

thread blocks of 64 or fewer threads (shared memory and register file resource

requirements permitting). Such kernels would have tended to under-utilize SMX,

but less so SMM.

Shared memory capacity is increased (see Shared Memory Capacity).

As such, developers can expect similar or improved occupancy on SMM without

changes to their application. At the same time, warp occupancy requirements (i.e.,

available parallelism) for maximum device utilization are similar to or less than those of

SMX (see Instruction Latencies).

1.4.1.2. Instruction Scheduling

The number of CUDA Cores per SM has been reduced to a power of two, however with

Maxwell's improved execution efficiency, performance per SM is usually within 10% of

Kepler performance, and the improved area efficiency of SMM means CUDA Cores per

GPU will be substantially higher vs. comparable Fermi or Kepler chips. SMM retains

the same number of instruction issue slots per clock and reduces arithmetic latencies

compared to the Kepler design.

As with SMX, each SMM has four warp schedulers. Unlike SMX, however, all SMM

core functional units are assigned to a particular scheduler, with no shared units. Along

with the selection of a power-of-two number of CUDA Cores per SM, which simplifies

scheduling and reduces stall cycles, this partitioning of SM computational resources in

SMM is a major component of the streamlined efficiency of SMM.

The power-of-two number of CUDA Cores per partition simplifies scheduling, as each

of SMM's warp schedulers issue to a dedicated set of CUDA Cores equal to the warp

width. Each warp scheduler still has the flexibility to dual-issue (such as issuing a math

operation to a CUDA Core in the same cycle as a memory operation to a load/store unit),

but single-issue is now sufficient to fully utilize all CUDA Cores.

1.4.1.3. Instruction Latencies

Another major improvement of SMM is that dependent math latencies have been

significantly reduced; a consequence of this is a further reduction of stall cycles, as the

available warp-level parallelism (i.e., occupancy) on SMM should be equal to or greater

than that of SMX (see Occupancy), while at the same time each math operation takes less

time to complete, improving utilization and throughput.

1.4.1.4. Instruction Throughput

The most significant changes to peak instruction throughputs in SMM are as follows:

‣

The change in number of CUDA Cores per SM brings with it a corresponding

change in peak single-precision floating point operations per clock per SM.

However, since the number of SMs is typically increased, the result is an increase in

aggregate peak throughput; furthermore, the scheduling and latency improvements

also discussed above make this peak easier to approach.

The throughput of many integer operations including multiply, logical operations

and shift is improved. In addition, there are now specialized integer instructions

‣

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 3

Maxwell Tuning Guide

that can accelerate pointer arithmetic. These instructions are most efficient when

data structures are a power of two in size.

As was already the recommended best practice, signed arithmetic should be

preferred over unsigned arithmetic wherever possible for best throughput on SMM.

The C language standard places more restrictions on overflow behavior for unsigned

math, limiting compiler optimization opportunities.

1.4.2. Memory Throughput

1.4.2.1. Unified L1/Texture Cache

Maxwell combines the functionality of the L1 and texture caches into a single unit.

As with Kepler, global loads in Maxwell are cached in L2 only, unless using the LDG

read-only data cache mechanism introduced in Kepler.

In a manner similar to Kepler GK110B, GM204 retains this behavior by default but also

allows applications to opt-in to caching of global loads in its unified L1/Texture cache.

The opt-in mechanism is the same as with GK110B: pass the

-Xptxas -dlcm=ca

flag to

nvcc

at compile time.

Local loads also are cached in L2 only, which could increase the cost of register spilling

if L1 local load hit rates were high with Kepler. The balance of occupancy versus

spilling should therefore be reevaluated to ensure best performance. Especially given

the improvements to arithmetic latencies, code built for Maxwell may benefit from

somewhat lower occupancy (due to increased registers per thread) in exchange for lower

spilling.

The unified L1/texture cache acts as a coalescing buffer for memory accesses, gathering

up the data requested by the threads of a warp prior to delivery of that data to the warp.

This function previously was served by the separate L1 cache in Fermi and Kepler.

Two new device attributes were added in CUDA Toolkit 6.0:

globalL1CacheSupported

and

localL1CacheSupported

. Developers who wish to

have separately-tuned paths for various architecture generations can use these fields to

simplify the path selection process.

Enabling caching of globals in GM204 can affect occupancy. If per-thread-block

SM resource usage would result in zero occupancy with caching enabled, the CUDA

driver will override the caching selection to allow the kernel launch to succeed. This

situation is reported by the profiler.

1.4.3. Shared Memory

1.4.3.1. Shared Memory Capacity

With Fermi and Kepler, shared memory and the L1 cache shared the same on-chip

storage. Maxwell, by contrast, provides dedicated space to the shared memory of each

SMM, since the functionality of the L1 and texture caches have been merged in SMM.

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 4

Maxwell Tuning Guide

This increases the shared memory space available per SMM as compared to SMX:

GM107 provides 64 KB shared memory per SMM, and GM204 further increases this to

96 KB shared memory per SMM.

This presents several benefits to application developers:

‣

Algorithms with significant shared memory capacity requirements (e.g., radix sort)

see an automatic 33% to 100% boost in capacity per SM on top of the aggregate boost

from higher SM count.

Applications no longer need to select a preference of the L1/shared split for

optimal performance. For purposes of backward compatibility with Fermi and

Kepler, applications may optionally continue to specify such a preference, but the

preference will be ignored on Maxwell, with the full 64 KB per SMM always going

to shared memory.

While the per-SM shared memory capacity is increased in SMM, the per-thread-

block limit remains 48 KB. For maximum flexibility on possible future GPUs, NVIDIA

recommends that applications use at most 32 KB of shared memory in any one thread

block, which would for example allow at least two such thread blocks to fit per SMM.

1.4.3.2. Shared Memory Bandwidth

Kepler SMX introduced an optional 8-byte shared memory banking mode, which had

the potential to increase shared memory bandwidth per SM over Fermi for shared

memory accesses of 8 or 16 bytes. However, applications could only benefit from this

when storing these larger elements in shared memory (i.e., integers and fp32 values saw

no benefit), and only when the developer explicitly opted into the 8-byte bank mode via

the API.

To simplify this, Maxwell returns to the Fermi style of shared memory banking, where

banks are always four bytes wide. Aggregate shared memory bandwidth across the chip

remains comparable to that of corresponding Kepler chips, given increased SM count.

In this way, all applications using shared memory can now benefit from the higher

bandwidth, even when storing only four-byte items into shared memory and without

specifying any particular preference via the API.

1.4.3.3. Fast Shared Memory Atomics

Kepler introduced a dramatically higher throughput for atomic operations to global

memory as compared to Fermi. However, atomic operations to shared memory remained

essentially unchanged: both architectures implemented shared memory atomics using

a lock/update/unlock pattern that could be expensive in the case of high contention for

updates to particular locations in shared memory.

Maxwell improves upon this by implementing native shared memory atomic operations

for 32-bit integers and native shared memory 32-bit and 64-bit compare-and-swap

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 5

Maxwell Tuning Guide

(CAS), which can be used to implement other atomic functions with reduced overhead

compared to the Fermi and Kepler methods.

Refer to the CUDA C Programming Guide for an example implementation of an fp64

atomicAdd()

using

atomicCAS()

1.4.4. Dynamic Parallelism

GK110 introduced a new architectural feature called Dynamic Parallelism, which allows

the GPU to create additional work for itself. A programming model enhancement

leveraging this feature was introduced in CUDA 5.0 to enable kernels running on GK110

to launch additional kernels onto the same GPU.

SMM brings Dynamic Parallelism into the mainstream by supporting it across

the product line, even in lower-power chips such as GM107. This will benefit

developers, as it means that applications will no longer need special-case algorithm

implementations for high-end GPUs that differ from those usable in more power-

constrained environments.

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 6

Version 1.0

‣

Initial Public Release

Version 1.1

‣

Updated for second-generation Maxwell (compute capability 5.2).

Tuning CUDA Applications for MaxwellDA-07173-001_v8.0 | 7

Notice

ALL NVIDIA DESIGN SPECIFICATIONS, REFERENCE BOARDS, FILES, DRAWINGS,

DIAGNOSTICS, LISTS, AND OTHER DOCUMENTS (TOGETHER AND SEPARATELY,

"MATERIALS") ARE BEING PROVIDED "AS IS." NVIDIA MAKES NO WARRANTIES,

EXPRESSED, IMPLIED, STATUTORY, OR OTHERWISE WITH RESPECT TO THE

MATERIALS, AND EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF

NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR

PURPOSE.

Information furnished is believed to be accurate and reliable. However, NVIDIA

Corporation assumes no responsibility for the consequences of use of such

information or for any infringement of patents or other rights of third parties

that may result from its use. No license is granted by implication of otherwise

under any patent rights of NVIDIA Corporation. Specifications mentioned in this

publication are subject to change without notice. This publication supersedes and

replaces all other information previously supplied. NVIDIA Corporation products

are not authorized as critical components in life support devices or systems

without express written approval of NVIDIA Corporation.

Trademarks

NVIDIA and the NVIDIA logo are trademarks or registered trademarks of NVIDIA

Corporation in the U.S. and other countries. Other company and product names

may be trademarks of the respective companies with which they are associated.