2024年3月21日发(作者：仪雨)
1，代码：Code
说明：Description
轿厢净宽：Car width
轿厢净深：Car depth
轿厢高度：Car height
美福电梯的图纸要求
开门净宽：Door open width
开门净高：Door open height
门洞净宽：Door hole width
门洞净高：Door hole height
井道净宽：Shaft width
井道净高：Shaft depth
顶层净高：Top floor height
底坑净深：Pit depth
提升高度：Rising height
机房净宽：Machine room width
机房净深：Machine room depth
机房净高：Machine room height
轿厢轨距：Car gauge
对重轨距：CW gauge
主副轨距：Rail gauge
主轨前距：Main rail distance
额定载荷：Rated capacity
额定速度：Rated speed
最大停站数：Max stops
最大提升高度：Max rising height
最小底坑深度：Min pit depth
最小顶层高度：Main top floor height
电机功率:Motor capacity
电源容量：Power capacity
动力电源：Power supply
照明电源：Light power supply
支撑点受力：Supporting stress
非标说明：Note
轿厢尺寸：Car size
开门形式尺寸：Door Size
2， 井道立面图：Shaft Vertical View
底坑受力分布图：Pit stress distribution
顶层吊钩位置图：the top hook locations
门洞留孔图：Door Hole
提升高度：travelling height （TH）
牛腿 ：haunched beam
吊钩：hook；
在吊钩处标明：marked on the hook
导轨支架每档间隔：ring beam each distance
层高：floor height
砼过梁：concrete beam
客户自理：by customer
门高：door height
弹性圆柱销：elastic cylindrical pin
顶层高：overhead height （OH）
控制柜安装孔（仅在顶层处预留，安装后填补）：
controller hole reservation(only top floor reserved fill after installation)
机房地面：machine floor
召唤箱孔：calling box
井道壁：shaft wall
缓冲器墩：buffer basement
爬梯：stairs
3.门洞净尺寸：net door hole height
4.井道右侧立视图： solid view of right side shaft
5.导轨支架连接点(圈梁等)间距每档：the spacing of rail bracket connection point (ring
beam,etc）/each file
6.井道照明间距每盏：shaft lighting spacing / each lamp
7.机房平面布置图:machine room plan
8.排风扇：exhaust fan
9.通风、采光窗：ventilation、lighting window
10.吊钩投影：hook projection
11.井道平面布置图：shaft plan
C向留孔：A direction hole reserved drawing
视图：D view
14.装修后楼面：decorated floor
15.安装完成后二次填充：after installing the second fill
向门洞留孔图：E direction/door hole reserved drawing
17.底坑平面布置图：pit view
请按实际数据填写pls fill in actual data
TR
TH
5层 5F
4层 4F
3层 3F
2层 2F
1层 1F
-1层 -1F
-2层 -2F
PD
层站 高度（mm）floor height(mm)
_层_站_门 _F_S_D
用户签字盖章处： customer signature
日期： date
供方签字盖章处： supply signature
日期：date
合同号：contract No.
设备号：Equip No.
注：本图需双方签章盖章后生效，本图非按比例绘制，请以标注尺寸为准，全部尺寸单位为
mm。
Note: this drawing should be signed before using, the drawing is not by scaling, this unit of
dimension is mm.
变更记录modify notes
版本 V.
标记mark
签名name
日期date
变更内容details of change
项目名称 project name
***工程 ×× Project
设计 design
电梯土建总体布置图 elevator construction drawing
校对 check
图号 draw No.
审核 approve
共1页 pages 1
第1页 page 1
比例 scale
版本 V.
18.注：缓冲器墩由用户配合制作，但在制作前需预置4根φ12钢筋，伸出坑底300以上，
均布在φ200的圆上。当提升高度大于30m时，缓冲器墩P2按虚线处布置，承载力按单个
P2/2计算。
Note: Client supply the buffer base, but 4φ12 reinforced bar which distribute on
φ200 circle,should be prepared, and leave 300mm beyond the pit.
when travel height more than30m，buffer base P2 installed according to dotted line,and
capacity calculated according to single P2/2.
19.用户单位在收到本公司的电梯土建图后，请及时确认，本图需经双方盖章确认后方可生
效，如需对确认并双方盖章的土建图更改，则由更改方承担相关责任
after the user recieved the construction drawing, please confirm in time, this is effective by
signed,
if need to correct the drawing, the corrector is in charge
Requirement(修改版)
1、
电源要求：需方应将电源送到机房门旁或控制屏预留孔旁墙上，高度约。 电源
为三相五线制、380V、50Hz交流电，允许电压波动为±7%，输入总功率需大于
主电机总功率50%以上。并配置与电源容量相应的的空气开关。允许附带漏电保
护器/功能，但变频调速时需用专用漏电保护开关。接地线的电阻值＜4Ω， 零
线和接地线应始终分开；
Power requirement: the buyer should send power to the wall beside machine room door or
beside the reserved hole of control screen, the height is about . The power is 3 phase 5 line、
380V、50Hz DC, and equipped with air switch which can protect from leakage. The allowed
voltage fluctuation is ±7%, total input power should be more than 50% of main motor power.
Grounding wire resistance ＜4Ω, the neutral wire and grounding wire should always be
separated.
2、
、井道要求：井道应为电梯专用，不得装设与电梯无关的设备(如管道、电缆
等)。电梯井道应有效阻止人体进入。井道的平面尺寸是指用铅垂线测得的最小
尺寸，允许偏差0～+50mm。原则上井道内不得有突出的梁、柱等。井道壁的耐
压≥24MPa。推荐采用全混凝土结构形式制作，并可不设预埋铁。如为实心砖墙
结构，应按图设置预埋铁或在预埋铁的水平面上浇制圈梁，高度≥300mm。如
为空心砖墙结构，可选择用C25混凝土灌实墙体，并在预埋铁的水平面上浇制圈
梁，高度≥300mm。当井道前壁为砖墙结构时，应在门洞上方设置混凝土过梁，
用于固定厅门支架，高度≥300mm。如图中有要求，则厅门口应按图浇制能承
受额定载重以上承载力的混凝土牛腿。井道内应设永久照明灯，照度≥50LX， 底
坑中缓冲器墩应由需方在电梯安装人员的指导下配合制作，但在制作前应预埋≥
4根插筋，材料≥∅12mm，伸出底坑地面≥300mm，该墩位置下的地面应能承受
图中给出的冲击力。底坑应防水。底坑里应有人能到达的空间。底坑爬梯由用户
自理， 底坑下面如果有人能到达的空间(如地下室)，应将对重缓冲器墩一直延
伸到下面的坚固地面。相邻两个层站的间距≥11m时，应在中间设置宽350mm，
高1800mm安全门。
Shaft requirement: the allowed deviation of shaft plan size is 0～50mm. , there should be no
prominent column in shaft, and equipments related to elevator should not exist also. Pressure of
shaft wall should be no less than 24MPa. Concrete structure is recommended. If it is solid brick,
cast coil beam on the embedded iron or the plane of embedded iron according the drawing, the
height should be no less than 300mm. If it is hollow brick, using C25 concrete to make the wall
solid, and cast coil beam on the plane of embedded iron, the height should be no less than
300mm. When the front wall of shaft is made of brick, mould a concrete beam above the door
hole to fix the landing door bracket, the height is no less than 300mm. Lighting in shaft should be
permanent, lighting degree is no less than 50LX. Buyer should mould buffer frusta at the direction
of installation member, Ground under this frusta should can support wallop given in the drawing.
The pit should be waterproof and have enough room for people to reach. Buyers should prepare
ladder by themselves, If the space under the pit can hold people (basement .), the
counterweight buffer frusta should be extended to the firm ground. Distance between two floors
should be no less than 11m, and a 1800-height and 350mm-width safety door should be set.
3、
机房要求(无机房电梯不适用)：应考虑适于主机运输的通道。机房内的通风窗、
排风扇等需安装完毕，保持机房内相对湿度≤85%，温度+5℃～40℃。楼板预留
孔四周需浇制50mm高翻口。地面应平整，并能承受700kg/m²的安装载荷(集中载
荷另加)。
Machine room requirement( not applied to machine room less elevator): considering channels
which can transport main motor well, After the installation of ventilator and blower, chine room
humidity no more than 86%, and machine room temperature is at +5℃～40℃. Cast a 50mm
prominent hole around reserved hole of floor. The ground should be flat and can support loading
of 700kg/m2(collective loading added externally);
4、
其它：用户如选择五地通话功能时，从机房到第五通话地的布线工作及电缆
材料(6*芯的PVC圆型电缆)由用户自理。该功能的布线长度不得大于200米。
图中相关尺寸均为净空尺寸，门口留洞高以装修后的地面为基准。未注墙厚默认
为240mm。厅门口待电梯安装完工后由需方粉刷或装修。
Others: relevant size in the drawing is net size, reserved hole height should be based on finished
ground. If it is not noted, the wall thickness is implied as 240mm. If choose 5-way telephone, the
layout of cable from machine room to the 5th phone place and cable material (6 × Core PVC
round cable) should be arranged by client, this function's max routing length is 200m. Landing
door entrance should be painted or decorated after the completion of elevator
2024年3月21日发(作者：仪雨)
1，代码：Code
说明：Description
轿厢净宽：Car width
轿厢净深：Car depth
轿厢高度：Car height
美福电梯的图纸要求
开门净宽：Door open width
开门净高：Door open height
门洞净宽：Door hole width
门洞净高：Door hole height
井道净宽：Shaft width
井道净高：Shaft depth
顶层净高：Top floor height
底坑净深：Pit depth
提升高度：Rising height
机房净宽：Machine room width
机房净深：Machine room depth
机房净高：Machine room height
轿厢轨距：Car gauge
对重轨距：CW gauge
主副轨距：Rail gauge
主轨前距：Main rail distance
额定载荷：Rated capacity
额定速度：Rated speed
最大停站数：Max stops
最大提升高度：Max rising height
最小底坑深度：Min pit depth
最小顶层高度：Main top floor height
电机功率:Motor capacity
电源容量：Power capacity
动力电源：Power supply
照明电源：Light power supply
支撑点受力：Supporting stress
非标说明：Note
轿厢尺寸：Car size
开门形式尺寸：Door Size
2， 井道立面图：Shaft Vertical View
底坑受力分布图：Pit stress distribution
顶层吊钩位置图：the top hook locations
门洞留孔图：Door Hole
提升高度：travelling height （TH）
牛腿 ：haunched beam
吊钩：hook；
在吊钩处标明：marked on the hook
导轨支架每档间隔：ring beam each distance
层高：floor height
砼过梁：concrete beam
客户自理：by customer
门高：door height
弹性圆柱销：elastic cylindrical pin
顶层高：overhead height （OH）
控制柜安装孔（仅在顶层处预留，安装后填补）：
controller hole reservation(only top floor reserved fill after installation)
机房地面：machine floor
召唤箱孔：calling box
井道壁：shaft wall
缓冲器墩：buffer basement
爬梯：stairs
3.门洞净尺寸：net door hole height
4.井道右侧立视图： solid view of right side shaft
5.导轨支架连接点(圈梁等)间距每档：the spacing of rail bracket connection point (ring
beam,etc）/each file
6.井道照明间距每盏：shaft lighting spacing / each lamp
7.机房平面布置图:machine room plan
8.排风扇：exhaust fan
9.通风、采光窗：ventilation、lighting window
10.吊钩投影：hook projection
11.井道平面布置图：shaft plan
C向留孔：A direction hole reserved drawing
视图：D view
14.装修后楼面：decorated floor
15.安装完成后二次填充：after installing the second fill
向门洞留孔图：E direction/door hole reserved drawing
17.底坑平面布置图：pit view
请按实际数据填写pls fill in actual data
TR
TH
5层 5F
4层 4F
3层 3F
2层 2F
1层 1F
-1层 -1F
-2层 -2F
PD
层站 高度（mm）floor height(mm)
_层_站_门 _F_S_D
用户签字盖章处： customer signature
日期： date
供方签字盖章处： supply signature
日期：date
合同号：contract No.
设备号：Equip No.
注：本图需双方签章盖章后生效，本图非按比例绘制，请以标注尺寸为准，全部尺寸单位为
mm。
Note: this drawing should be signed before using, the drawing is not by scaling, this unit of
dimension is mm.
变更记录modify notes
版本 V.
标记mark
签名name
日期date
变更内容details of change
项目名称 project name
***工程 ×× Project
设计 design
电梯土建总体布置图 elevator construction drawing
校对 check
图号 draw No.
审核 approve
共1页 pages 1
第1页 page 1
比例 scale
版本 V.
18.注：缓冲器墩由用户配合制作，但在制作前需预置4根φ12钢筋，伸出坑底300以上，
均布在φ200的圆上。当提升高度大于30m时，缓冲器墩P2按虚线处布置，承载力按单个
P2/2计算。
Note: Client supply the buffer base, but 4φ12 reinforced bar which distribute on
φ200 circle,should be prepared, and leave 300mm beyond the pit.
when travel height more than30m，buffer base P2 installed according to dotted line,and
capacity calculated according to single P2/2.
19.用户单位在收到本公司的电梯土建图后，请及时确认，本图需经双方盖章确认后方可生
效，如需对确认并双方盖章的土建图更改，则由更改方承担相关责任
after the user recieved the construction drawing, please confirm in time, this is effective by
signed,
if need to correct the drawing, the corrector is in charge
Requirement(修改版)
1、
电源要求：需方应将电源送到机房门旁或控制屏预留孔旁墙上，高度约。 电源
为三相五线制、380V、50Hz交流电，允许电压波动为±7%，输入总功率需大于
主电机总功率50%以上。并配置与电源容量相应的的空气开关。允许附带漏电保
护器/功能，但变频调速时需用专用漏电保护开关。接地线的电阻值＜4Ω， 零
线和接地线应始终分开；
Power requirement: the buyer should send power to the wall beside machine room door or
beside the reserved hole of control screen, the height is about . The power is 3 phase 5 line、
380V、50Hz DC, and equipped with air switch which can protect from leakage. The allowed
voltage fluctuation is ±7%, total input power should be more than 50% of main motor power.
Grounding wire resistance ＜4Ω, the neutral wire and grounding wire should always be
separated.
2、
、井道要求：井道应为电梯专用，不得装设与电梯无关的设备(如管道、电缆
等)。电梯井道应有效阻止人体进入。井道的平面尺寸是指用铅垂线测得的最小
尺寸，允许偏差0～+50mm。原则上井道内不得有突出的梁、柱等。井道壁的耐
压≥24MPa。推荐采用全混凝土结构形式制作，并可不设预埋铁。如为实心砖墙
结构，应按图设置预埋铁或在预埋铁的水平面上浇制圈梁，高度≥300mm。如
为空心砖墙结构，可选择用C25混凝土灌实墙体，并在预埋铁的水平面上浇制圈
梁，高度≥300mm。当井道前壁为砖墙结构时，应在门洞上方设置混凝土过梁，
用于固定厅门支架，高度≥300mm。如图中有要求，则厅门口应按图浇制能承
受额定载重以上承载力的混凝土牛腿。井道内应设永久照明灯，照度≥50LX， 底
坑中缓冲器墩应由需方在电梯安装人员的指导下配合制作，但在制作前应预埋≥
4根插筋，材料≥∅12mm，伸出底坑地面≥300mm，该墩位置下的地面应能承受
图中给出的冲击力。底坑应防水。底坑里应有人能到达的空间。底坑爬梯由用户
自理， 底坑下面如果有人能到达的空间(如地下室)，应将对重缓冲器墩一直延
伸到下面的坚固地面。相邻两个层站的间距≥11m时，应在中间设置宽350mm，
高1800mm安全门。
Shaft requirement: the allowed deviation of shaft plan size is 0～50mm. , there should be no
prominent column in shaft, and equipments related to elevator should not exist also. Pressure of
shaft wall should be no less than 24MPa. Concrete structure is recommended. If it is solid brick,
cast coil beam on the embedded iron or the plane of embedded iron according the drawing, the
height should be no less than 300mm. If it is hollow brick, using C25 concrete to make the wall
solid, and cast coil beam on the plane of embedded iron, the height should be no less than
300mm. When the front wall of shaft is made of brick, mould a concrete beam above the door
hole to fix the landing door bracket, the height is no less than 300mm. Lighting in shaft should be
permanent, lighting degree is no less than 50LX. Buyer should mould buffer frusta at the direction
of installation member, Ground under this frusta should can support wallop given in the drawing.
The pit should be waterproof and have enough room for people to reach. Buyers should prepare
ladder by themselves, If the space under the pit can hold people (basement .), the
counterweight buffer frusta should be extended to the firm ground. Distance between two floors
should be no less than 11m, and a 1800-height and 350mm-width safety door should be set.
3、
机房要求(无机房电梯不适用)：应考虑适于主机运输的通道。机房内的通风窗、
排风扇等需安装完毕，保持机房内相对湿度≤85%，温度+5℃～40℃。楼板预留
孔四周需浇制50mm高翻口。地面应平整，并能承受700kg/m²的安装载荷(集中载
荷另加)。
Machine room requirement( not applied to machine room less elevator): considering channels
which can transport main motor well, After the installation of ventilator and blower, chine room
humidity no more than 86%, and machine room temperature is at +5℃～40℃. Cast a 50mm
prominent hole around reserved hole of floor. The ground should be flat and can support loading
of 700kg/m2(collective loading added externally);
4、
其它：用户如选择五地通话功能时，从机房到第五通话地的布线工作及电缆
材料(6*芯的PVC圆型电缆)由用户自理。该功能的布线长度不得大于200米。
图中相关尺寸均为净空尺寸，门口留洞高以装修后的地面为基准。未注墙厚默认
为240mm。厅门口待电梯安装完工后由需方粉刷或装修。
Others: relevant size in the drawing is net size, reserved hole height should be based on finished
ground. If it is not noted, the wall thickness is implied as 240mm. If choose 5-way telephone, the
layout of cable from machine room to the 5th phone place and cable material (6 × Core PVC
round cable) should be arranged by client, this function's max routing length is 200m. Landing
door entrance should be painted or decorated after the completion of elevator