2024年3月26日发(作者：赧秀隽)
Meizu MX3 Battery Replacement
This guide shows how to replace the battery in the 5.1 inch Meizu MX3
Redigido por: Mandela Robin
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
FERRAMENTAS:
iFixit Opening Tools (1)
64 Bit Driver Kit (1)
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
Passo 1 — Removing the Back Cover
Insert the plastic opening tool in between the charging port and the back case of the device. Slowly
move the tool to the left of the until you come the top by the power button.
Using a paper clip or pointed edge spudger push in the pin located in the bottom right had corner
of the back of the phone.
Passo 2 — Removing the Screws in the Internal Casing
Using one of the small Phillips screwdriver bits provided unscrew the 11 screws present on the
protective plastic plate under the device case.
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
Passo 3 — Removing the Battery
After the 11 screws are loosened use the plastic opening tool and gently pry the protective plate
from the back of the device.
Once the plate is off, use the same tool to gently remove the 3 ribbon cables located directly above
the battery.
On the left side of the battery on the phone case, there is a groove where the plastic opening tool
can be inserted to pry the battery up and out.
The battery might be glued to the phone so exercise caution.
To reassemble your device, follow these instructions in reverse order.
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
2024年3月26日发(作者：赧秀隽)
Meizu MX3 Battery Replacement
This guide shows how to replace the battery in the 5.1 inch Meizu MX3
Redigido por: Mandela Robin
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
FERRAMENTAS:
iFixit Opening Tools (1)
64 Bit Driver Kit (1)
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
Passo 1 — Removing the Back Cover
Insert the plastic opening tool in between the charging port and the back case of the device. Slowly
move the tool to the left of the until you come the top by the power button.
Using a paper clip or pointed edge spudger push in the pin located in the bottom right had corner
of the back of the phone.
Passo 2 — Removing the Screws in the Internal Casing
Using one of the small Phillips screwdriver bits provided unscrew the 11 screws present on the
protective plastic plate under the device case.
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA
Passo 3 — Removing the Battery
After the 11 screws are loosened use the plastic opening tool and gently pry the protective plate
from the back of the device.
Once the plate is off, use the same tool to gently remove the 3 ribbon cables located directly above
the battery.
On the left side of the battery on the phone case, there is a groove where the plastic opening tool
can be inserted to pry the battery up and out.
The battery might be glued to the phone so exercise caution.
To reassemble your device, follow these instructions in reverse order.
Este documento foi gerado em 2021-01-29 11:50:42 AM (MST).
© iFixit — CC BY-NC-SA