2024年9月22日发(作者：机原)
PCE-5120 LGA775 Intel® Pentium® D /
Pentium® 4 / Celeron® D Processor Card with
PCI Express / IPMI / VGA / Dual Gigabit LAN
Before you begin installing your card, please make
sure that the following materials have been shipped:
• 1 PCE-5120 Dual Intel® Pentium® D/Pentium® 4/
Celeron® D processor-based single board computer
• 1 PCE-5120 Startup Manual
• 1 CD with driver utility and manual (in PDF format)
• 1 FDD cable
• 1 Ultra ATA 66/100 HDD cables
p/n: 1700340640
p/n: 1701400452
Standard SBC Functions
• CPU: Supports Intel® LGA 775 Pentium® D/ Pentium®
4/ Celeron® D processors up to 3.2/3.8/3.06 GHz, FSB
533/800 MHz.
• BIOS: Award® 4 Mb Flash memory BIOS
• Chipset: Intel® 945G with ICH7R
• System Memory: Dual Channel; Four 240-pin DIMM
sockets accepts up to 4 GB DDR2 533/667 SDRAM
Note: Due to inherent limitations of the PC architecture,
the system may not fully detect 4 GB RAM if 4 GB
RAM is installed.
• SATA/IDE interface: Supports up to four independent
• 2 Serial ATA HDD data cablep/n: 1700071000
• 2 Serial ATA HDD power cablep/n: 1703150102
• 1 Printer (parallel) port & COM p/n: 1701260305
port cable kit
• 1 Dual COM port cable kit p/n: 1701092300
• 1 Y cable for PS/2 keyboard p/n: 1700060202
and PS/2 mouse
• 1 CPU coolerp/n: 1750000400
• 1 USB cable with 4 ports p/n: 1700002314
• Warranty card
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Note 1: For detailed contents of the PCE-5120, please
refer to the enclosed CD-ROM (in PDF format).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
/Prodindex/acrobat/read-
(Acrobat is a trademark of Adobe.)
For more information on this and other Advantech
products, please visit our website at:
/eplatform
For technical support and service, please visit our
support website at:
/support
This manual is for the PCE-5120 series Rev. A1.
Part No. 2st. Edition
Printed in Taiwan
July 2006
SATA2 hard drives (up to 300MB/s) with software RAID
0,1, 5,10 functions; supports up to one IDE hard disk
drives, or two enhanced IDE devices. The IDE port may
be altered to a Type II CF socket.
• FDD interface: Supports up to two FDDs
• Serial ports: Four serial RS-232 ports; COM2 can be
configured to RS-232/422/485 thru pin header
• Parallel port: One parallel port, supports SPP/EPP/
ECP mode
• Keyboard/mouse connector: Supports one standard
PS/2 keyboard and mouse connector and one external
6-pin pin header.
• Watchdog timer: 255 level timer intervals
• USB (2.0): Four Universal Serial Bus ports to Backplane
and four ports on board
VGA Interface
• Chipset: Intel® 945G integrated
• Display memory: Shared with 224 MB system memory
• Video Output: Up to 2048 x 1536 @ 75 Hz refresh
• External Card: PCI Express X16 Graphic Card inter-
face to back plane
Ethernet Interface
• Chipset:
LAN1: Intel 82573V (PCIe GbE)
LAN2: Intel 82573V (PCIe GbE)
• Connection: On-board RJ-45 connector x 2
Mechanical and Environmental
• Dimensions: (L x W): 338 x 122 mm
• Power supply voltage: +5 V ± 12 V
• Power requirements:
CPU: Intel® Pentium® D 3.2 GHz/2M/800/130W
MEMORY: DDR2 667 MHz 1 GB x 4
Test program,Intel Max power 100% + BurnIn Test 4.0
+12V15 A
+5V2 A
4
D
+3.3V20 A
+5VSB0.7 A
-12V0 A
-5V0 A
• Operating temperature:
0 ~ 55 °C (depending on CPU)
• Weight: 0.5 kg (weight of board)
PCE-5120 Startup Manual 1
The board has a number of connectors and jumpers that
allow you to configure your system to suit your application.
The table below lists the function of each of the connec-
tors and jumpers.
Connectors
IDE1Primary IDE connector
FDD1 Floppy drive connector
LPT1 Parallel port
VGA1VGA connector
COM1 Serial port:COM1 ( 9-pin connector)
COM2 Serial port:COM2 ( 9-pin connector)
COM3 Serial port:COM3 ( 9-pin connector)
COM4 Serial port:COM4 ( 9-pin connector)
KBMS1 PS/2 keyboard and mouse connector
KBMS2 External keyboard/mouse connector
JIR1Reserved
CPUFAN1 CPU1 FAN connector
JFP1 Power and Reset Button connector
JFP2 HDD LED/SNMP SMbus/Speaker connector
JFP3 Power LED and keyboard lock connector
JOBS1HW Monitor Alarm
Close: Enable OBS Alarm
Open: Disable OBS Alarm
LAN1
Giga LAN RJ45 connector
LAN2Giga LAN RJ45 connector
AC97AC’97 Link connector
SATA1 Serial ATA1
SATA2Serial ATA2
SATA3 Serial ATA3
SATA4Serial ATA4
LANLED1LAN1 and LAN2 LED connector
BMC1BMC connector
USB12Two USB port pin headers
USB34Two USB port pin headers
EXPCI1HIROSA Extended PCI connector (Optional)
Jumpers
CMOS1CMOS clear
JWDT1Watchdog timer output selection
JSETCOM2COM2 RS232/422/485 selection
Closed PinsResult
1-2Keep CMOS data*
2-3Clear CMOS
123
*
default setting
2 PCE-5120 Startup Manual
Closed PinsResult
1-2Reserved
2-3System reset *
123
* default setting
COM2 Port FunctionJumper Configuration
RS-232*
31
642
RS-422
31
642
RS-485
31
642
*
default setting
• The CD disc contains a driver installer program that will
lead you through the installation of various device driv-
ers needed to take full advantage of your CPU card.
The computer is provided with a battery-powered
Real-time Clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace only
with same or equivalent type recommended by the
manufacturer. Discard used batteries according to
manufacturer's instructions
This device complies with the requirements in Part 15
of the FCC rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
The location of all connectors and jumpers:
Board Layout: Jumper and Connector Location
PCE-5120 Startup Manual 3
Please ensure that the CPU cooler included with the
PCE-5120 is installed as follows:
CPU Cooler Installation
4 PCE-5120 Startup Manual
2024年9月22日发(作者：机原)
PCE-5120 LGA775 Intel® Pentium® D /
Pentium® 4 / Celeron® D Processor Card with
PCI Express / IPMI / VGA / Dual Gigabit LAN
Before you begin installing your card, please make
sure that the following materials have been shipped:
• 1 PCE-5120 Dual Intel® Pentium® D/Pentium® 4/
Celeron® D processor-based single board computer
• 1 PCE-5120 Startup Manual
• 1 CD with driver utility and manual (in PDF format)
• 1 FDD cable
• 1 Ultra ATA 66/100 HDD cables
p/n: 1700340640
p/n: 1701400452
Standard SBC Functions
• CPU: Supports Intel® LGA 775 Pentium® D/ Pentium®
4/ Celeron® D processors up to 3.2/3.8/3.06 GHz, FSB
533/800 MHz.
• BIOS: Award® 4 Mb Flash memory BIOS
• Chipset: Intel® 945G with ICH7R
• System Memory: Dual Channel; Four 240-pin DIMM
sockets accepts up to 4 GB DDR2 533/667 SDRAM
Note: Due to inherent limitations of the PC architecture,
the system may not fully detect 4 GB RAM if 4 GB
RAM is installed.
• SATA/IDE interface: Supports up to four independent
• 2 Serial ATA HDD data cablep/n: 1700071000
• 2 Serial ATA HDD power cablep/n: 1703150102
• 1 Printer (parallel) port & COM p/n: 1701260305
port cable kit
• 1 Dual COM port cable kit p/n: 1701092300
• 1 Y cable for PS/2 keyboard p/n: 1700060202
and PS/2 mouse
• 1 CPU coolerp/n: 1750000400
• 1 USB cable with 4 ports p/n: 1700002314
• Warranty card
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Note 1: For detailed contents of the PCE-5120, please
refer to the enclosed CD-ROM (in PDF format).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
/Prodindex/acrobat/read-
(Acrobat is a trademark of Adobe.)
For more information on this and other Advantech
products, please visit our website at:
/eplatform
For technical support and service, please visit our
support website at:
/support
This manual is for the PCE-5120 series Rev. A1.
Part No. 2st. Edition
Printed in Taiwan
July 2006
SATA2 hard drives (up to 300MB/s) with software RAID
0,1, 5,10 functions; supports up to one IDE hard disk
drives, or two enhanced IDE devices. The IDE port may
be altered to a Type II CF socket.
• FDD interface: Supports up to two FDDs
• Serial ports: Four serial RS-232 ports; COM2 can be
configured to RS-232/422/485 thru pin header
• Parallel port: One parallel port, supports SPP/EPP/
ECP mode
• Keyboard/mouse connector: Supports one standard
PS/2 keyboard and mouse connector and one external
6-pin pin header.
• Watchdog timer: 255 level timer intervals
• USB (2.0): Four Universal Serial Bus ports to Backplane
and four ports on board
VGA Interface
• Chipset: Intel® 945G integrated
• Display memory: Shared with 224 MB system memory
• Video Output: Up to 2048 x 1536 @ 75 Hz refresh
• External Card: PCI Express X16 Graphic Card inter-
face to back plane
Ethernet Interface
• Chipset:
LAN1: Intel 82573V (PCIe GbE)
LAN2: Intel 82573V (PCIe GbE)
• Connection: On-board RJ-45 connector x 2
Mechanical and Environmental
• Dimensions: (L x W): 338 x 122 mm
• Power supply voltage: +5 V ± 12 V
• Power requirements:
CPU: Intel® Pentium® D 3.2 GHz/2M/800/130W
MEMORY: DDR2 667 MHz 1 GB x 4
Test program,Intel Max power 100% + BurnIn Test 4.0
+12V15 A
+5V2 A
4
D
+3.3V20 A
+5VSB0.7 A
-12V0 A
-5V0 A
• Operating temperature:
0 ~ 55 °C (depending on CPU)
• Weight: 0.5 kg (weight of board)
PCE-5120 Startup Manual 1
The board has a number of connectors and jumpers that
allow you to configure your system to suit your application.
The table below lists the function of each of the connec-
tors and jumpers.
Connectors
IDE1Primary IDE connector
FDD1 Floppy drive connector
LPT1 Parallel port
VGA1VGA connector
COM1 Serial port:COM1 ( 9-pin connector)
COM2 Serial port:COM2 ( 9-pin connector)
COM3 Serial port:COM3 ( 9-pin connector)
COM4 Serial port:COM4 ( 9-pin connector)
KBMS1 PS/2 keyboard and mouse connector
KBMS2 External keyboard/mouse connector
JIR1Reserved
CPUFAN1 CPU1 FAN connector
JFP1 Power and Reset Button connector
JFP2 HDD LED/SNMP SMbus/Speaker connector
JFP3 Power LED and keyboard lock connector
JOBS1HW Monitor Alarm
Close: Enable OBS Alarm
Open: Disable OBS Alarm
LAN1
Giga LAN RJ45 connector
LAN2Giga LAN RJ45 connector
AC97AC’97 Link connector
SATA1 Serial ATA1
SATA2Serial ATA2
SATA3 Serial ATA3
SATA4Serial ATA4
LANLED1LAN1 and LAN2 LED connector
BMC1BMC connector
USB12Two USB port pin headers
USB34Two USB port pin headers
EXPCI1HIROSA Extended PCI connector (Optional)
Jumpers
CMOS1CMOS clear
JWDT1Watchdog timer output selection
JSETCOM2COM2 RS232/422/485 selection
Closed PinsResult
1-2Keep CMOS data*
2-3Clear CMOS
123
*
default setting
2 PCE-5120 Startup Manual
Closed PinsResult
1-2Reserved
2-3System reset *
123
* default setting
COM2 Port FunctionJumper Configuration
RS-232*
31
642
RS-422
31
642
RS-485
31
642
*
default setting
• The CD disc contains a driver installer program that will
lead you through the installation of various device driv-
ers needed to take full advantage of your CPU card.
The computer is provided with a battery-powered
Real-time Clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace only
with same or equivalent type recommended by the
manufacturer. Discard used batteries according to
manufacturer's instructions
This device complies with the requirements in Part 15
of the FCC rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
The location of all connectors and jumpers:
Board Layout: Jumper and Connector Location
PCE-5120 Startup Manual 3
Please ensure that the CPU cooler included with the
PCE-5120 is installed as follows:
CPU Cooler Installation
4 PCE-5120 Startup Manual