2024年5月12日发(作者：门嘉树)

11

Installation

Emergency Assist Alarm - CFEAPULLKIT

Kit Contents

This kit comprises of everything required for the complete instalation of a BS8300 Compliant

Emergency Assistance Alarm, (excluding cables and fixings).

PART CODE - CFEAODI

PART CODE - CFEAPSU

PART CODE - CFEARSP

PART CODE - CFEAPULL

Mains Wiring

The general requirement for the mains supply to the call controller is fixed wiring, using three core cable

2

of not less than 1mm . This should be fed from an isolating switched fused spur, fused at 3A, which is

marked appropriately and secure from unauthorised operation.

Extra Low Voltage (ELV) Wiring

Always segregate low voltage wiring from the mains wiring.

System requires minimum 2 core 0.4mm

2

cable.

All wall-mounting devices should be mounted onto a back box of the required depth.

Wiring Guide Using 2 Core Cable

PSU 12V supply Over Door Indicator

Over Door Indicator Cancel Unit

Cancel UnitPull Cord Unit

Power

Supply

Pull Cord Unit

+

-

-

12V

+

-

+

IN

-

+

OUT

Over Door

Indicator

-

IN

+

-

+

OUT

Cancel

Unit

Incorrect wiring may cause damage to the circuit, which will void the warranty.

2PR211-180-521-03 (25-15112-A) September 2018

Emergency Assist Alarm - CFEAPULLKIT

Installation

The Emergency Assist Alarm should be installed in accordance with the recommendations of BS8300

and to the requirements of Building Regulations Approved Document M.

The below diagram demonstrates a typical layout for installation in a disabled person toilet.

Note: Where pertinent other or alternative standards of design and installation should be adhered to.

Knot the cord to ensure the lowest

ring is 100mm from the floor.

Cut off excess cord.

Ceiling Pull is surface mounted.

The Ceiling Pull should be

positioned so that its

readily assessable from

the WC, bath

(where applicable)

The Power Supply

is sited in corridor

and supplied via

switched fuse spur

The Over Door Indicator

provides an audibly and

visually signal to

indicate the area where

assistance is required.

Screw the

two piece connctor

together

100mm

The Cancel Button

should be positioned so

that it is reachable from

the WC and a wheelchair.

The upper cord pull should be located between

800mm & 1000mm above floor level.

The lower cord pull should be exactly 100mm above floor

level (remove excess cord)

All system components are designed to be sited internally and positioned in locations where they are

readily accessible by the user. The area should be clean and dry and sound and light levels allow the

status of all device indicators and sounders to be seen and heard.

Any likelihood of tampering or vandalism should also be taken into account at time of design.

Operation

Power Supply Unit power LED is lit.

Operate the Pull Cord. LED’s will illuminate on, Pull Cord Unit, Cancel Unit and

Over Door Indicator. An internal buzzer will also sound in the Over Door Indicator.

Press the Cancel Button.

Maintenance

Clean plates with a non abrasive cleaning cloth and detergent, do not use harsh

or solvent based cleaners.

Test Call system by making and resetting a call.

PR211-180-521-03 (25-15112-A) September 2018

3

Eaton Electrical Systems Ltd.

Wheatley Hall Road, Doncaster, South

Yorkshire, DN2 4NB, United Kingdom

Eaton

EMEA Headquarters

Route de la Longeraie 7

1110 Morges, Switzerland

7

TEL: +44(0)1302 321541

FAX: +44(0)1302 30220

*****************************

*************************

2018 Eaton

All Rights Reserved

Sep 2018

Eaton is a registered trademark.

All other trademarks are property

of their respective owners.

©

2024年5月12日发(作者：门嘉树)

11

Installation

Emergency Assist Alarm - CFEAPULLKIT

Kit Contents

This kit comprises of everything required for the complete instalation of a BS8300 Compliant

Emergency Assistance Alarm, (excluding cables and fixings).

PART CODE - CFEAODI

PART CODE - CFEAPSU

PART CODE - CFEARSP

PART CODE - CFEAPULL

Mains Wiring

The general requirement for the mains supply to the call controller is fixed wiring, using three core cable

2

of not less than 1mm . This should be fed from an isolating switched fused spur, fused at 3A, which is

marked appropriately and secure from unauthorised operation.

Extra Low Voltage (ELV) Wiring

Always segregate low voltage wiring from the mains wiring.

System requires minimum 2 core 0.4mm

2

cable.

All wall-mounting devices should be mounted onto a back box of the required depth.

Wiring Guide Using 2 Core Cable

PSU 12V supply Over Door Indicator

Over Door Indicator Cancel Unit

Cancel UnitPull Cord Unit

Power

Supply

Pull Cord Unit

+

-

-

12V

+

-

+

IN

-

+

OUT

Over Door

Indicator

-

IN

+

-

+

OUT

Cancel

Unit

Incorrect wiring may cause damage to the circuit, which will void the warranty.

2PR211-180-521-03 (25-15112-A) September 2018

Emergency Assist Alarm - CFEAPULLKIT

Installation

The Emergency Assist Alarm should be installed in accordance with the recommendations of BS8300

and to the requirements of Building Regulations Approved Document M.

The below diagram demonstrates a typical layout for installation in a disabled person toilet.

Note: Where pertinent other or alternative standards of design and installation should be adhered to.

Knot the cord to ensure the lowest

ring is 100mm from the floor.

Cut off excess cord.

Ceiling Pull is surface mounted.

The Ceiling Pull should be

positioned so that its

readily assessable from

the WC, bath

(where applicable)

The Power Supply

is sited in corridor

and supplied via

switched fuse spur

The Over Door Indicator

provides an audibly and

visually signal to

indicate the area where

assistance is required.

Screw the

two piece connctor

together

100mm

The Cancel Button

should be positioned so

that it is reachable from

the WC and a wheelchair.

The upper cord pull should be located between

800mm & 1000mm above floor level.

The lower cord pull should be exactly 100mm above floor

level (remove excess cord)

All system components are designed to be sited internally and positioned in locations where they are

readily accessible by the user. The area should be clean and dry and sound and light levels allow the

status of all device indicators and sounders to be seen and heard.

Any likelihood of tampering or vandalism should also be taken into account at time of design.

Operation

Power Supply Unit power LED is lit.

Operate the Pull Cord. LED’s will illuminate on, Pull Cord Unit, Cancel Unit and

Over Door Indicator. An internal buzzer will also sound in the Over Door Indicator.

Press the Cancel Button.

Maintenance

Clean plates with a non abrasive cleaning cloth and detergent, do not use harsh

or solvent based cleaners.

Test Call system by making and resetting a call.

PR211-180-521-03 (25-15112-A) September 2018

3

Eaton Electrical Systems Ltd.

Wheatley Hall Road, Doncaster, South

Yorkshire, DN2 4NB, United Kingdom

Eaton

EMEA Headquarters

Route de la Longeraie 7

1110 Morges, Switzerland

7

TEL: +44(0)1302 321541

FAX: +44(0)1302 30220

*****************************

*************************

2018 Eaton

All Rights Reserved

Sep 2018

Eaton is a registered trademark.

All other trademarks are property

of their respective owners.

©