Tascam DP-01 DP-01FX Quick Start Guide-USB迷|专注于互联网分享

2024年6月7日发(作者：潭怀寒)

DP-01 / DP-01FX

Quick Start Guide

his guide is designed to get you up-and-running

with the DP-01 and DP-01FX. If you have any

questions that aren’t answered in this short guide,

consult the Users Guide for detailed information

on using your new Digital Portastudio.

Build a New Song

e’ll begin by creating a new song ﬁ le so that

you have a fresh slate to work from.

1. Press the MENU button. Turn the data wheel

until you reach SONG and press the right cursor

button.

2. Turn the data wheel to select CREATE and press

the right cursor button.

3. If you want, use the DATA WHEEL to name your

new song. Otherwise, or afterwards, press EN-

TER.

Record a Track

he DP-01 gives you eight tracks to record to.

This allows you to record a guitar, rewind, play

bass over that part, and continue repeating until

your song is ﬁ nished.

1. Plug an instrument or microphone into Input

A, on the front of the DP-01.

2. If you plugged a guitar or bass directly into the

DP-01, set the front-panel switch to GUITAR.

Otherwise, set it to MIC/LINE. If you’re using

a condenser microphone on the DP-01FX, turn

phantom power ON.

3. While watching the meters on the LCD screen,

turn the front-panel trim knob so that your

loudest notes do not make the meter go all the

way to the top.

3. Hold down the button above the input labeled

ASSIGN A. While you’re still holding that but-

ton, press the REC button above one of the eight

track faders. It will ﬂ ash to show you that your

input has been assigned to that track.

4. Press the REC button that you just assigned the

input to. It will ﬂ ash slowly.

5. Press the PLAY and RECORD buttons to start

recording. When you’re ﬁ nished, press STOP

and press the REC button to disarm the track.

6. To record another track and play along with the

one you just recorded, ﬁ rst press the ASSIGN A

button and press the REC button of the track

you just recorded to. This “de-assigns” the input

from that track. Press the REC button for one of

the other tracks, rewind to the beginning of the

song, and then repeat steps 4 and 5.

Note: You will hear your instrument through

the master outputs even if no tracks are armed.

DP-01 / DP-01FX

Quick Start Guide

Using the Reverb Effect (DP-01FX)

he DP-01FX has a dedicated Reverb effect that’s

available to all tracks. Each channel has an Ef-

fect Send knob so that you can control the amount

of reverb – lots of reverb for the drums, a little on

the vocal, etc. Here’s how you set that up.

1. If the REVERB light is not on, hold the SHIFT

button and press REVERB.

2. Let go of the SHIFT button and press REVERB

again. The LCD window will show you what

reverb type is selected.

3. Turn the TYPE knob to change to a different

reverb type: Hall, Room, Live or Studio.

4. Turn the PARAMETER knob to change the decay

time of the reverb for a larger or smaller-sound-

ing space.

5. Send your recorded tracks to the reverb proces-

sor using the EFFECT SEND knobs above those

channel faders and adjust the overall level of

the external effect using the EFFECT RETURN

knob.

Using External Effects

f you have a reverb or multieffects processor, you

can plug it into the DP-01 to use in your mix.

1. Plug the SEND on the rear panel of the DP-01

into the input of your effects processor.

2. Plug the outputs of your effects processor into

the RETURN inputs of the DP-01.

3. Set the Mix control on your effects processor to

100% wet.

4. [DP-01FX only] Turn off the internal reverb pro-

cessor by holding the SHIFT button and pressing

the REVERB button (the light will go out).

5. Send your recorded tracks to the effects proces-

sor using the EFFECT SEND knobs above those

channel faders.

6. You can adjust the overall level of the external

effect using the EFFECT RETURN knob.

Using the Multi Effect (DP-01FX)

he DP-01FX has two effects processors. The

Multi effect processes the input as it’s recorded

to disk, while the Reverb effect is only for the mix-

down and only gets recorded when you master your

song. This section explains how to use the Multi:

1. Plug a guitar or other sound source into one of

the front-panel inputs.

2. Set the INPUT MODE switch on the front panel

to MONO.

3. While holding SHIFT, press the MULTI button.

The LED next to the button will show whether

the effect is processing the A input, B input or

neither one.

4. Let go of the SHIFT button and press MULTI

again. The LCD screen will show you what ef-

fect program is selected. The ﬁ rst line shows

the name of the program (“CoolPick”), and the

second line shows what instrument it’s designed

for (“EGTR”).

5. Turn the TYPE knob to change to a different

effect program.

6. Turn the PARAMETER knob to change the sound

of that program.

DP-01 / DP-01FX

Quick Start Guide

Bounce Tracks

et’s say you’re recording your rock opera and

you need more tracks than you have available.

You can “bounce” tracks on the DP-01, which means

mixing them down to other tracks and recording

over the ﬁ rst set of tracks. To do this:

1. Press the BOUNCE button. (It lights up in Bounce

mode)

2. Press the REC button above the track you want

to bounce to. If you want to mix your tracks

in stereo (leaving six available), press the REC

button over a second track.

3. You can record yourself using the inputs dur-

ing your bounce. If you don’t want to do this,

unplug any mics or guitars to make sure there

isn’t any noise on your tracks.

4. Press PLAY and RECORD at the beginning of your

song. You can change the levels, panning (in

stereo) and effects while you record the bounce.

Press STOP at the end of the song.

5. You can now record new parts over your previ-

ous tracks.

Mix Your Song

nce all of the parts in your arrangement have

been recorded, you’ll want to mix these down

to a stereo master track to transfer to CD, MP3 or

some other format that you can share.

1. Use the channel faders to set the level for each

track.

2. Turn the PAN knobs to adjust the stereo position

for each track.

3. Use the EQ HIGH and EQ LOW knobs to adjust

the tone of each track.

4. Use the EFFECT SEND knob to send a track to

an external effects processor (if attached) or

built-in reverb (DP-01FX only). Use the EFFECT

RETURN knob to control the overall level of the

effect.

5. When you have a mix you’re happy with, press

the MASTER button. It will start ﬂ ashing.

6. Rewind to the beginning of your song. Hold

the SHIFT button and press SET IN to set your

beginning point.

7. Fast Forward to the end of your song. Hold the

SHIFT button and press SET OUT.

8. Rewind to the beginning of the song. Make sure

the MASTER light is still ﬂ ashing and press PLAY

and RECORD.

9. As your mix is being recorded, you can change

levels, panning, effects and even fade the Master

level down at the end of the song. When the

recorder reaches the end of the song (which

you set using the SET OUT button), recording

will stop.

10. Press the MASTER button again. It will light up

solid. You can rewind to the beginning of the

song and listen to the mix you just recorded.

If you’re happy with your mix, you’ll want to

transfer it to a computer to encode it as an MP3 or

burn it to a CD. See the next step for information

on how to do this.

DP-01 / DP-01FX

Quick Start Guide

Transfer Your Song to a Computer

nce you create a Master Recording, as

described in the previous section, you’re

ready to burn it to an audio CD or encode an

MP3. This section tells you how to transfer a

single song to your computer. For information

on creating a playlist with multiple songs,

consult the User’s Guide.

1. Press the MENU button. Turn the data wheel

until you reach WAVE and press the right

cursor button.

2. Turn the data wheel to select EXPORT MSTR.

and press the right cursor button. (If the

MASTER button is lit, press it until it goes

out.)

3. Use the DATA WHEEL to name your song

mix and then press ENTER.

4. The DP-01 will copy the song to a ﬁ le on an-

other part of the hard drive accessible by your

computer. You now need to put the DP-01 in

USB mode so that you can copy this ﬁ le to

your computer for backup onto a CD.

5. Press MENU to get back to the main screen,

then press MENU again.

6. Select DISK and press the right cursor but-

ton.

7. Select USB OPN/CLS and press the right cursor

button. (If the DP-01 is not in USB mode, you

may see an error message when connecting

it to your computer.)

8. You can now connect the DP-01 to your com-

puter using a USB cable. The DP-01 will show

up on your computer as another hard drive.

Copy the song backup ﬁ le ending in “.001” to

your computer and burn it to a CD. Press the

EXIT button when you are ﬁ nished.

Backup Your Song

ou should backup your hard drive to ar-

chive old projects and prevent data loss.

(You should also ﬂ oss daily and wear a seat

belt.) To back up your song to a CD:

1. Press the MENU button. Turn the data wheel

until you reach BACKUP and press the right

cursor button.

2. Turn the data wheel to select SONG BACKUP

and press the right cursor button.

3. Use the DATA WHEEL to select a song for backup

and press ENTER.

4. The DP-01 will copy the song to a ﬁ le on an-

other part of the hard drive accessible by your

computer.

You now need to put the DP-01 in USB mode

so that you can copy this ﬁ le to your computer

for backup onto a CD. See steps 5 through 8 of

“Transfer Your Song to a Computer” (above) to

put the DP-01 into USB mode.

7733 Telegraph Rd • Montebello, CA • 90640 • phone 323.726.0303 •

speciﬁ cations subject to change without notice.

2024年6月7日发(作者：潭怀寒)

DP-01 / DP-01FX

Quick Start Guide

his guide is designed to get you up-and-running

with the DP-01 and DP-01FX. If you have any

questions that aren’t answered in this short guide,

consult the Users Guide for detailed information

on using your new Digital Portastudio.

Build a New Song

e’ll begin by creating a new song ﬁ le so that

you have a fresh slate to work from.

1. Press the MENU button. Turn the data wheel

until you reach SONG and press the right cursor

button.

2. Turn the data wheel to select CREATE and press

the right cursor button.

3. If you want, use the DATA WHEEL to name your

new song. Otherwise, or afterwards, press EN-

TER.

Record a Track

he DP-01 gives you eight tracks to record to.

This allows you to record a guitar, rewind, play

bass over that part, and continue repeating until

your song is ﬁ nished.

1. Plug an instrument or microphone into Input

A, on the front of the DP-01.

2. If you plugged a guitar or bass directly into the

DP-01, set the front-panel switch to GUITAR.

Otherwise, set it to MIC/LINE. If you’re using

a condenser microphone on the DP-01FX, turn

phantom power ON.

3. While watching the meters on the LCD screen,

turn the front-panel trim knob so that your

loudest notes do not make the meter go all the

way to the top.

3. Hold down the button above the input labeled

ASSIGN A. While you’re still holding that but-

ton, press the REC button above one of the eight

track faders. It will ﬂ ash to show you that your

input has been assigned to that track.

4. Press the REC button that you just assigned the

input to. It will ﬂ ash slowly.

5. Press the PLAY and RECORD buttons to start

recording. When you’re ﬁ nished, press STOP

and press the REC button to disarm the track.

6. To record another track and play along with the

one you just recorded, ﬁ rst press the ASSIGN A

button and press the REC button of the track

you just recorded to. This “de-assigns” the input

from that track. Press the REC button for one of

the other tracks, rewind to the beginning of the

song, and then repeat steps 4 and 5.

Note: You will hear your instrument through

the master outputs even if no tracks are armed.

DP-01 / DP-01FX

Quick Start Guide

Using the Reverb Effect (DP-01FX)

he DP-01FX has a dedicated Reverb effect that’s

available to all tracks. Each channel has an Ef-

fect Send knob so that you can control the amount

of reverb – lots of reverb for the drums, a little on

the vocal, etc. Here’s how you set that up.

1. If the REVERB light is not on, hold the SHIFT

button and press REVERB.

2. Let go of the SHIFT button and press REVERB

again. The LCD window will show you what

reverb type is selected.

3. Turn the TYPE knob to change to a different

reverb type: Hall, Room, Live or Studio.

4. Turn the PARAMETER knob to change the decay

time of the reverb for a larger or smaller-sound-

ing space.

5. Send your recorded tracks to the reverb proces-

sor using the EFFECT SEND knobs above those

channel faders and adjust the overall level of

the external effect using the EFFECT RETURN

knob.

Using External Effects

f you have a reverb or multieffects processor, you

can plug it into the DP-01 to use in your mix.

1. Plug the SEND on the rear panel of the DP-01

into the input of your effects processor.

2. Plug the outputs of your effects processor into

the RETURN inputs of the DP-01.

3. Set the Mix control on your effects processor to

100% wet.

4. [DP-01FX only] Turn off the internal reverb pro-

cessor by holding the SHIFT button and pressing

the REVERB button (the light will go out).

5. Send your recorded tracks to the effects proces-

sor using the EFFECT SEND knobs above those

channel faders.

6. You can adjust the overall level of the external

effect using the EFFECT RETURN knob.

Using the Multi Effect (DP-01FX)

he DP-01FX has two effects processors. The

Multi effect processes the input as it’s recorded

to disk, while the Reverb effect is only for the mix-

down and only gets recorded when you master your

song. This section explains how to use the Multi:

1. Plug a guitar or other sound source into one of

the front-panel inputs.

2. Set the INPUT MODE switch on the front panel

to MONO.

3. While holding SHIFT, press the MULTI button.

The LED next to the button will show whether

the effect is processing the A input, B input or

neither one.

4. Let go of the SHIFT button and press MULTI

again. The LCD screen will show you what ef-

fect program is selected. The ﬁ rst line shows

the name of the program (“CoolPick”), and the

second line shows what instrument it’s designed

for (“EGTR”).

5. Turn the TYPE knob to change to a different

effect program.

6. Turn the PARAMETER knob to change the sound

of that program.

DP-01 / DP-01FX

Quick Start Guide

Bounce Tracks

et’s say you’re recording your rock opera and

you need more tracks than you have available.

You can “bounce” tracks on the DP-01, which means

mixing them down to other tracks and recording

over the ﬁ rst set of tracks. To do this:

1. Press the BOUNCE button. (It lights up in Bounce

mode)

2. Press the REC button above the track you want

to bounce to. If you want to mix your tracks

in stereo (leaving six available), press the REC

button over a second track.

3. You can record yourself using the inputs dur-

ing your bounce. If you don’t want to do this,

unplug any mics or guitars to make sure there

isn’t any noise on your tracks.

4. Press PLAY and RECORD at the beginning of your

song. You can change the levels, panning (in

stereo) and effects while you record the bounce.

Press STOP at the end of the song.

5. You can now record new parts over your previ-

ous tracks.

Mix Your Song

nce all of the parts in your arrangement have

been recorded, you’ll want to mix these down

to a stereo master track to transfer to CD, MP3 or

some other format that you can share.

1. Use the channel faders to set the level for each

track.

2. Turn the PAN knobs to adjust the stereo position

for each track.

3. Use the EQ HIGH and EQ LOW knobs to adjust

the tone of each track.

4. Use the EFFECT SEND knob to send a track to

an external effects processor (if attached) or

built-in reverb (DP-01FX only). Use the EFFECT

RETURN knob to control the overall level of the

effect.

5. When you have a mix you’re happy with, press

the MASTER button. It will start ﬂ ashing.

6. Rewind to the beginning of your song. Hold

the SHIFT button and press SET IN to set your

beginning point.

7. Fast Forward to the end of your song. Hold the

SHIFT button and press SET OUT.

8. Rewind to the beginning of the song. Make sure

the MASTER light is still ﬂ ashing and press PLAY

and RECORD.

9. As your mix is being recorded, you can change

levels, panning, effects and even fade the Master

level down at the end of the song. When the

recorder reaches the end of the song (which

you set using the SET OUT button), recording

will stop.

10. Press the MASTER button again. It will light up

solid. You can rewind to the beginning of the

song and listen to the mix you just recorded.

If you’re happy with your mix, you’ll want to

transfer it to a computer to encode it as an MP3 or

burn it to a CD. See the next step for information

on how to do this.

DP-01 / DP-01FX

Quick Start Guide

Transfer Your Song to a Computer

nce you create a Master Recording, as

described in the previous section, you’re

ready to burn it to an audio CD or encode an

MP3. This section tells you how to transfer a

single song to your computer. For information

on creating a playlist with multiple songs,

consult the User’s Guide.

1. Press the MENU button. Turn the data wheel

until you reach WAVE and press the right

cursor button.

2. Turn the data wheel to select EXPORT MSTR.

and press the right cursor button. (If the

MASTER button is lit, press it until it goes

out.)

3. Use the DATA WHEEL to name your song

mix and then press ENTER.

4. The DP-01 will copy the song to a ﬁ le on an-

other part of the hard drive accessible by your

computer. You now need to put the DP-01 in

USB mode so that you can copy this ﬁ le to

your computer for backup onto a CD.

5. Press MENU to get back to the main screen,

then press MENU again.

6. Select DISK and press the right cursor but-

ton.

7. Select USB OPN/CLS and press the right cursor

button. (If the DP-01 is not in USB mode, you

may see an error message when connecting

it to your computer.)

8. You can now connect the DP-01 to your com-

puter using a USB cable. The DP-01 will show

up on your computer as another hard drive.

Copy the song backup ﬁ le ending in “.001” to

your computer and burn it to a CD. Press the

EXIT button when you are ﬁ nished.

Backup Your Song

ou should backup your hard drive to ar-

chive old projects and prevent data loss.

(You should also ﬂ oss daily and wear a seat

belt.) To back up your song to a CD:

1. Press the MENU button. Turn the data wheel

until you reach BACKUP and press the right

cursor button.

2. Turn the data wheel to select SONG BACKUP

and press the right cursor button.

3. Use the DATA WHEEL to select a song for backup

and press ENTER.

4. The DP-01 will copy the song to a ﬁ le on an-

other part of the hard drive accessible by your

computer.

You now need to put the DP-01 in USB mode

so that you can copy this ﬁ le to your computer

for backup onto a CD. See steps 5 through 8 of

“Transfer Your Song to a Computer” (above) to

put the DP-01 into USB mode.

7733 Telegraph Rd • Montebello, CA • 90640 • phone 323.726.0303 •

speciﬁ cations subject to change without notice.

USB迷 | 专注于互联网分享

Tascam DP-01 DP-01FX Quick Start Guide

与本文相关的文章

评论列表 (0)