2024年7月15日发(作者：植智志)
Ho200
使用说明书
本说明书的内容可能会随版本更改, 如有变动, 恕不另行通知Ver 1.0
Ho200
请将本音响系统安装在通风良好、阴凉、干燥、干净的位置，远离直射阳光热源
、振动、灰尘、 潮湿或寒冷。
只能使用本机指定的电压。使用高于指定数值的电压很危险，而且可能导致火
灾，损坏本机或造成人身伤害。对于使用高于指定电压造成的任何损害，
我司
将不负任何责任。
不要试图自行改造或修理本机。如果需要任何服务，请与销售或者我司客服人
员联系。不管有任何理由，都没有打开机壳的必要。
如果打算长时间不使用本机（比如度假时），请从墙壁交流电源插座上断开电
源线的连接。
重要提示：
本说明书内容如有更新,恕不另行通知.若您使用的产品功能与说明书不一致
时,请以产品为准!
一、服务期限
佛山双木三林科技有限公司承诺产品的良好品质，产品自售出之后7天内
正常使用情况下出现故障，客户可以选择退货或者保修（不影响二次销售
才可退货）。正常使用一年内出现故障可以免费保修。
二、购买日期以销售商开出的购机发票或收据日期为准，网购可以交易截图为准。
三、有以下情况都不能享受“三包”服务
1.一切人为因素损坏，包括非正常工作环境下使用或不按照说明书使用。
2.用户私自拆机、改装、维修。
3.使用非指定或许可的配件造成损坏的。
4.机身的QC或保修贴损毁。
5.不能出示有效购机凭证。
6.不属于本公司产品。
四、保修方式为送修
此条款只适于中国大陆，其它地区请参考当地销售代理商的规定和国家法规。
Ho200
全平衡设计, 4路超低失真精密线性反馈电路(PLFC)!
失真度低至0.00006%, 信噪比高达140dB!
超低噪声电源设计, 使输出噪声低到1.0uV(APX555B实测值, 不是等效值!)
高输出功率, 16欧姆输出功率达6W, 32欧时达到3W ;
特别设计的音量电位器, 大大降低通道偏差;
高中低三档可切换增益控制, 低增益专门为IEM优化;
前级输出功能, 可以作为Hi-End前级使用;
经典复古拨动开关操作 ;
超紧凑设计，
高精度低温漂电阻,性能不受温度影响 ;
非常适合桌面耳机系统 ;
高品质继电器和无冲击声设计 ;
20Hz至500kHz频率响应 ;
耳机放大器具有直流, 过压, 过载保护等全面保护 ;
内置高效低噪声的电源系统.
Ho200
技术参数
输入方式 ...............................................................................
平衡 x1 ,非平衡 x1
前级输出方式 ..........
.........................................................平衡
x
1
, 非平衡耳机x1
耳放输出方式 ..........
...................4.4mm平衡
x
1
, XLR平衡 x1, 6.35mm单端 x1
输出功率:
..............................................................................................
6W x 2 (16 Ω)
...............................................................................................
3W x 2 (32 Ω)
信噪比 ......................................................................................................140dB
剩余噪音
.................................................................................................
1.0 uV
THD+N ..........................................................
-123dB, 0.00006% (1kHz , 32 Ω)
THD+N ..........................................
-120dB, 0.00013% (20-20kHz , 32 Ω , 0dB)
THD
....................................................................................................
<-125dB
输入阻抗 ....................................................................................................10kΩ
耳放输出阻抗 ......................................................................................
接近 0 Ω
前级输出阻抗:
..........................................
平衡接口 44Ω
频率响应
...........................................................................
20Hz - 500kHz(-3dB)
..........................................非平衡接口 低
(
-10dB) ,中(0dB) ,高
(
17dB
)
..........................................
非平衡接口 22Ω
增益
:
能量功耗(EN60065)
..................................................................................<30W
重量 ........................................................................................................1.23kg
..........................................平衡接口 低
(
-4dB) ,中(6dB) ,高
(
23dB
)
待机功耗 .................................................................................................<0.1W
体积 ..........................................................................210X40X170mm(WxHxD)
规格时有变更，恕不另行通知。
Ho200
98765
43
2
1
10
1
2
11
开关
指示灯
12
13
8
9
14
6.35mm耳机插座
平衡耳机插座
XLR平衡输入
RCA输入
RCA前级输出
XLR前级输出
AC电源输入接口
(
AC100-240V
)
3
5
6
4
增益选择
输出选择
输入选择
旋钮
10
11
12
13
7
4.4mm平衡耳机插座
14
注:
1.连接耳机前请调小音量 , 以免音量过大损坏耳机;
2.根据健康专家的建议 , 请勿长时间聆听耳机以免影响听力;
3.指示灯开机后为蓝色 , 若红色闪烁表示系统触发保护。
Ho200
USER MANUAL
The contents of this manual may be changed with the edition,
and are subject to change without notice
Ver 1.0
Ho200
Safety Notes
Install this unit in a well ventilated, cool, dry, clean place-away from direct sunlight, heat
sources, vibration, dust, moisture, or cold..
Use the voltage specified on this unit Only. Using this unit with a higher voltage than
specified is dangerous and may cause fire , damage to this unit, or personal injury. Our
company will not be held responsible for any damage resulting from the use of this unit
with a voltage other than that specified.
Do not attempt to modify or fix this unit by yourself. Contact alesperson or customer
service when any service is needed. The cabinet should never be opened for any reason.
When not planning to use this unit for long periods of time (i.e. when going on vacation),
disconnect the power cable from the AC wall outlet.
Important note:
The product specifications and information mentioned in this manual are for reference
only. The content of this manual is subject to change without notice.
Warranty Terms
Term of Service
Foshan Shuangmusanlin Technology Co., Ltd promises to offer good-quality products. If the
product is broken in 7 days after purchasing when you use it normally, you can choose to
send it back for return, replacement or repairing (only the product does not affect the
second sales can be returned ). Repairing for free in one year if you use it normally.
of purchase is in accordance with the date on invoice or receipt uesd by seller, and if
you buy it on line, you can show the screenshot of trade.
an inappropriate usage causes the unit damaged, the warranty will be void. As below.
All damages by inappropriate use, including using it under non-normal working
environment or without following the instructions.
Dismantling, refitting, repairing by user in private.
Causing damage by using some fittings instead of the designative or accredited ones.
Cannot provide credible proof of purchase.
g it back to our company for repairing.
t your S.M.S.L Audio reseller for a return or replacement.
Ho200
Features
Fully balanced design, 4 ultra-low distortion precision linear feedback circuit
(PLFC)!
The distortion is as low as 0.00006%, and the A-WTD is as low as 0.00005%
(-126dB)!
Ultra-low noise power supply design, so that the output noise is as low as
1.0uV, SNR up to 140dB !
High output power, 16 ohm output power up to 6W, 32 ohms up to 3W;
The specially designed volume potentiometer greatly reduces channel
deviation;
3 gears gain control, low gain is specially optimized for IEM;
Pre-out function, can be used as Hi-End pre-amp;
Classic retro toggle switch operation;
Ultra-compact design, very suitable for desktop headphone system;
High-precision low-temperature drift resistance, performance is not affected
by temperature;
High-quality relay and non-impact sound design;
20Hz to 500kHz frequency response;
The headphone amplifier has comprehensive protections such as DC,
overvoltage, and overload protection;
Built-in high-efficiency and low-noise power system.
Ho200
Specifications
Balanced x1, Unbalanced x1
Headphone outputs:
........................4.4mm Balanced x1 , XLR 4 Pin x1 , 6.35mm unbalanced x1
Balanced x1, Unbalanced x1
Output Power:
...............................................................................................6W x 2 (16 Ω)
...............................................................................................3W x 2 (32 Ω)
140dB
1.0uV
-123dB, 0.00006% (1kHz, 32 Ω)
-120dB, 0.00013% (20-20kHz , 32 Ω, 0dB)
<-125dB
10kΩ
AMP Near 0 Ω
Pre-output Impedance:
Balanced .............................................................................................44Ω
Unbalanced ..........................................................................................22Ω
20Hz - 500kHz(-3dB)
Gain:
Low(-4dB) , Middle(6dB) , High(23dB)
Power consumption(EN60065)...................................................................<30 W
Power consumption in <0.1W
.....
...........210X40X170mm(WxHxD)
1.23
kg
Specifications are subject to change without notice.
. Low(-10dB) , Middle(0dB) , High(17dB)
Ho200
Display Interface and Instructions
98765
43
2
1
10
1
Power switch
2
Indicator light
3
Gain selection
4
Output selection
5
Input selection
6
Volume
11
12
13
14
8
6.35mm headphone jack
9
Balanced headphone jack
10
XLR balanced input
11
RCA input
12
RCA Pre-output
13
XLR Pre-output
14
Power AC input(AC100-240V)
7
4.4mm balanced headphone jack
Note:
Please turn down the volume before connecting the headphones to avoid
excessive volume damage to the headset.
According to the advice of health experts, do not listen to the headphones
for a long time so as not affect your hearing.
The indicator light turns blue after it is turned on. Flashing red means the
system has triggered protection.
2024年7月15日发(作者：植智志)
Ho200
使用说明书
本说明书的内容可能会随版本更改, 如有变动, 恕不另行通知Ver 1.0
Ho200
请将本音响系统安装在通风良好、阴凉、干燥、干净的位置，远离直射阳光热源
、振动、灰尘、 潮湿或寒冷。
只能使用本机指定的电压。使用高于指定数值的电压很危险，而且可能导致火
灾，损坏本机或造成人身伤害。对于使用高于指定电压造成的任何损害，
我司
将不负任何责任。
不要试图自行改造或修理本机。如果需要任何服务，请与销售或者我司客服人
员联系。不管有任何理由，都没有打开机壳的必要。
如果打算长时间不使用本机（比如度假时），请从墙壁交流电源插座上断开电
源线的连接。
重要提示：
本说明书内容如有更新,恕不另行通知.若您使用的产品功能与说明书不一致
时,请以产品为准!
一、服务期限
佛山双木三林科技有限公司承诺产品的良好品质，产品自售出之后7天内
正常使用情况下出现故障，客户可以选择退货或者保修（不影响二次销售
才可退货）。正常使用一年内出现故障可以免费保修。
二、购买日期以销售商开出的购机发票或收据日期为准，网购可以交易截图为准。
三、有以下情况都不能享受“三包”服务
1.一切人为因素损坏，包括非正常工作环境下使用或不按照说明书使用。
2.用户私自拆机、改装、维修。
3.使用非指定或许可的配件造成损坏的。
4.机身的QC或保修贴损毁。
5.不能出示有效购机凭证。
6.不属于本公司产品。
四、保修方式为送修
此条款只适于中国大陆，其它地区请参考当地销售代理商的规定和国家法规。
Ho200
全平衡设计, 4路超低失真精密线性反馈电路(PLFC)!
失真度低至0.00006%, 信噪比高达140dB!
超低噪声电源设计, 使输出噪声低到1.0uV(APX555B实测值, 不是等效值!)
高输出功率, 16欧姆输出功率达6W, 32欧时达到3W ;
特别设计的音量电位器, 大大降低通道偏差;
高中低三档可切换增益控制, 低增益专门为IEM优化;
前级输出功能, 可以作为Hi-End前级使用;
经典复古拨动开关操作 ;
超紧凑设计，
高精度低温漂电阻,性能不受温度影响 ;
非常适合桌面耳机系统 ;
高品质继电器和无冲击声设计 ;
20Hz至500kHz频率响应 ;
耳机放大器具有直流, 过压, 过载保护等全面保护 ;
内置高效低噪声的电源系统.
Ho200
技术参数
输入方式 ...............................................................................
平衡 x1 ,非平衡 x1
前级输出方式 ..........
.........................................................平衡
x
1
, 非平衡耳机x1
耳放输出方式 ..........
...................4.4mm平衡
x
1
, XLR平衡 x1, 6.35mm单端 x1
输出功率:
..............................................................................................
6W x 2 (16 Ω)
...............................................................................................
3W x 2 (32 Ω)
信噪比 ......................................................................................................140dB
剩余噪音
.................................................................................................
1.0 uV
THD+N ..........................................................
-123dB, 0.00006% (1kHz , 32 Ω)
THD+N ..........................................
-120dB, 0.00013% (20-20kHz , 32 Ω , 0dB)
THD
....................................................................................................
<-125dB
输入阻抗 ....................................................................................................10kΩ
耳放输出阻抗 ......................................................................................
接近 0 Ω
前级输出阻抗:
..........................................
平衡接口 44Ω
频率响应
...........................................................................
20Hz - 500kHz(-3dB)
..........................................非平衡接口 低
(
-10dB) ,中(0dB) ,高
(
17dB
)
..........................................
非平衡接口 22Ω
增益
:
能量功耗(EN60065)
..................................................................................<30W
重量 ........................................................................................................1.23kg
..........................................平衡接口 低
(
-4dB) ,中(6dB) ,高
(
23dB
)
待机功耗 .................................................................................................<0.1W
体积 ..........................................................................210X40X170mm(WxHxD)
规格时有变更，恕不另行通知。
Ho200
98765
43
2
1
10
1
2
11
开关
指示灯
12
13
8
9
14
6.35mm耳机插座
平衡耳机插座
XLR平衡输入
RCA输入
RCA前级输出
XLR前级输出
AC电源输入接口
(
AC100-240V
)
3
5
6
4
增益选择
输出选择
输入选择
旋钮
10
11
12
13
7
4.4mm平衡耳机插座
14
注:
1.连接耳机前请调小音量 , 以免音量过大损坏耳机;
2.根据健康专家的建议 , 请勿长时间聆听耳机以免影响听力;
3.指示灯开机后为蓝色 , 若红色闪烁表示系统触发保护。
Ho200
USER MANUAL
The contents of this manual may be changed with the edition,
and are subject to change without notice
Ver 1.0
Ho200
Safety Notes
Install this unit in a well ventilated, cool, dry, clean place-away from direct sunlight, heat
sources, vibration, dust, moisture, or cold..
Use the voltage specified on this unit Only. Using this unit with a higher voltage than
specified is dangerous and may cause fire , damage to this unit, or personal injury. Our
company will not be held responsible for any damage resulting from the use of this unit
with a voltage other than that specified.
Do not attempt to modify or fix this unit by yourself. Contact alesperson or customer
service when any service is needed. The cabinet should never be opened for any reason.
When not planning to use this unit for long periods of time (i.e. when going on vacation),
disconnect the power cable from the AC wall outlet.
Important note:
The product specifications and information mentioned in this manual are for reference
only. The content of this manual is subject to change without notice.
Warranty Terms
Term of Service
Foshan Shuangmusanlin Technology Co., Ltd promises to offer good-quality products. If the
product is broken in 7 days after purchasing when you use it normally, you can choose to
send it back for return, replacement or repairing (only the product does not affect the
second sales can be returned ). Repairing for free in one year if you use it normally.
of purchase is in accordance with the date on invoice or receipt uesd by seller, and if
you buy it on line, you can show the screenshot of trade.
an inappropriate usage causes the unit damaged, the warranty will be void. As below.
All damages by inappropriate use, including using it under non-normal working
environment or without following the instructions.
Dismantling, refitting, repairing by user in private.
Causing damage by using some fittings instead of the designative or accredited ones.
Cannot provide credible proof of purchase.
g it back to our company for repairing.
t your S.M.S.L Audio reseller for a return or replacement.
Ho200
Features
Fully balanced design, 4 ultra-low distortion precision linear feedback circuit
(PLFC)!
The distortion is as low as 0.00006%, and the A-WTD is as low as 0.00005%
(-126dB)!
Ultra-low noise power supply design, so that the output noise is as low as
1.0uV, SNR up to 140dB !
High output power, 16 ohm output power up to 6W, 32 ohms up to 3W;
The specially designed volume potentiometer greatly reduces channel
deviation;
3 gears gain control, low gain is specially optimized for IEM;
Pre-out function, can be used as Hi-End pre-amp;
Classic retro toggle switch operation;
Ultra-compact design, very suitable for desktop headphone system;
High-precision low-temperature drift resistance, performance is not affected
by temperature;
High-quality relay and non-impact sound design;
20Hz to 500kHz frequency response;
The headphone amplifier has comprehensive protections such as DC,
overvoltage, and overload protection;
Built-in high-efficiency and low-noise power system.
Ho200
Specifications
Balanced x1, Unbalanced x1
Headphone outputs:
........................4.4mm Balanced x1 , XLR 4 Pin x1 , 6.35mm unbalanced x1
Balanced x1, Unbalanced x1
Output Power:
...............................................................................................6W x 2 (16 Ω)
...............................................................................................3W x 2 (32 Ω)
140dB
1.0uV
-123dB, 0.00006% (1kHz, 32 Ω)
-120dB, 0.00013% (20-20kHz , 32 Ω, 0dB)
<-125dB
10kΩ
AMP Near 0 Ω
Pre-output Impedance:
Balanced .............................................................................................44Ω
Unbalanced ..........................................................................................22Ω
20Hz - 500kHz(-3dB)
Gain:
Low(-4dB) , Middle(6dB) , High(23dB)
Power consumption(EN60065)...................................................................<30 W
Power consumption in <0.1W
.....
...........210X40X170mm(WxHxD)
1.23
kg
Specifications are subject to change without notice.
. Low(-10dB) , Middle(0dB) , High(17dB)
Ho200
Display Interface and Instructions
98765
43
2
1
10
1
Power switch
2
Indicator light
3
Gain selection
4
Output selection
5
Input selection
6
Volume
11
12
13
14
8
6.35mm headphone jack
9
Balanced headphone jack
10
XLR balanced input
11
RCA input
12
RCA Pre-output
13
XLR Pre-output
14
Power AC input(AC100-240V)
7
4.4mm balanced headphone jack
Note:
Please turn down the volume before connecting the headphones to avoid
excessive volume damage to the headset.
According to the advice of health experts, do not listen to the headphones
for a long time so as not affect your hearing.
The indicator light turns blue after it is turned on. Flashing red means the
system has triggered protection.