Silicon Labs BRD4310A 无线极客无线电板说明书-USB迷|专注于互联网分享

2024年10月24日发(作者：台琪华)

BGM220SC12 Module Radio Board

BRD4310A Reference Manual

The BRD4310A Wireless Gecko Radio Board contains a Wireless Gecko module which

integrates Silicon Labs' EFR32BG22 Wireless Gecko SoC into a small form factor Sys-

tem-in-Package (SiP) module. The fully certified module contains all components (a

high-performance transceiver, an energy efficient 32-bit MCU, HF crystal, RF passives,

and antenna) required for a system-level implementation of Bluetooth

Low Energy

wireless networks operating in the 2.4 GHz band with 0 dBm output power.

The BRD4310A Wireless Gecko Radio Board plugs into the Wireless Starter Kit Main-

board, which is included with the Wireless Gecko Starter Kit and gives access to dis-

play, buttons, and additional features from expansion boards. With the supporting Sim-

plicity Studio suite of tools, developers can take advantage of graphical wireless appli-

cation development, BGScript for Python-like scripting, and visual energy profiling and

optimization.

This document contains a brief introduction and description of the BRD4310A Radio

Board features, focusing on the RF performance.

RADIO BOARD FEATURES

•Wireless Module: BGM220SC12WGA2

•

CPU core: ARM Cortex

-M33

•Flash memory: 352 kB

•RAM: 32 kB

•Operation frequency: 2.4 GHz

•Transmit power: 0 dBm

•Integrated chip antenna, RF matching

network, HF crystal, and decoupling

•Option for UFL connector

•Crystal for LFXO: 32.768 kHz

•8 Mbit low-power serial flash for over-the-

air updates

| Building a more connected . 0.1

Table of Contents

1. 3

2. Radio 4

2.1

.42.2 Radio Board Connector Pin Associations.

3. Radio Board 5

3.1

3.2 Radio Board Block Diagram

3.3 Radio Board Block Description

3.3.1

3.3.2 LF Crystal Oscillator (LFXO)

3.3.3

3.3.4 Radio Board Connectors.

3.3.5

3.3.6

4. 7

5. .8

5.1

5.2 EMC Regulations for 2.

5.2.1 ETSI EN 300-328 Emission Limits for the 2400-2483.5 MHz Band

5.2.2 FCC15.247 Emission Limits for the 2400-2483.5 MHz Band..

5.2.3 Applied Emission Limits for the 2.4

6. .9

6.1 Conducted

6.1.1 Conducted Power Measurements with Unmodulated Carrier.

6.2 Radiated

6.2.1 Radiated Measurements in the 2.4 GHz Band.

6.2.2 Antenna

.10

7. EMC

7.1 Recommendations for 2.4 GHz ETSI EN 300-328 Compliance.

7.2 Recommendations for 2.4 GHz FCC 15.

.12

8. Board 13

10. Document

BRD4310A Reference Manual

Introduction

1. Introduction

The BRD4310A Radio Boards provide a development platform (together with the Wireless Starter Kit Mainboard) for the Silicon Labs

Wireless Gecko modules.

By carrying the BGM220SC12 module, the BRD4310A Radio Board is designed to operate in the 2400-2483.5 MHz with the maximum

of 0 dBm output power.

To develop and/or evaluate the BGM220SC12 module, the BRD4310A Radio Board can be connected to the Wireless Starter Kit Main-

board to get access to display, buttons, and additional features from expansion boards (EXP boards).

BRD4310A Reference Manual

Radio Board Connector

2. Radio Board Connector

2.1 Introduction

The board-to-board connector scheme allows access to all BGM220SC12 GPIO pins as well as the RESETn signal. For more informa-

tion on the functions of the available pins, see the BGM220SC12 data sheet.

2.2 Radio Board Connector Pin Associations

The figure below shows the mapping between the connector and the BGM220SC12 pins and their function on the Wireless Starter Kit

Mainboard.

P200

Upper Row

3v3

NC / P36

NC / P38

NC / P40

DBG_TDO_SWO / PA03 / P42

NC / P44

DBG_TMS_SWDIO / PA02 / F0

DBG_TDO_SWO / PA03 / F2

DBG_RESET / #RESET / F4

VCOM_TX / PA05 / F6

VCOM_CTS / PA08 / F8

UIF_BUTTON0 / UIF_LED0 / PB00 / F10

UIF_BUTTON0 / UIF_LED0 / PB00 / F12

DISP_ENABLE / PD03 / F14

DISP_MOSI / PC00 / F16

DISP_EXTCOMIN / PA00 / F18

PTI_DATA / PC04 / F20

USB_VBUS

Board ID SCL

GND

P37 / PD02 / SENSOR_ENABLE

P39 / NC

P41 / PA04* / DBG_TDI*

P43 / NC

P45 / NC

F1 / PA01 / DBG_TCK_SWCLK

F3 / PA04* / DBG_TDI*

F5 / PB04 / VCOM_ENABLE

F7 / PA06 / VCOM_RX

F9 / PA07 / VCOM_RTS

F11 / PB01 / UIF_BUTTON1 / UIF_LED1

F13 / PB01 / UIF_BUTTON1 / UIF_LED1

F15 / PC02 / DISP_SCLK

F17 / PC06 / DISP_SCS

F19 / PC05 / PTI_SYNC

F21 / NC

USB_VREG

GND

Board ID SDA

P201

Lower Row

GND

PC01** / P0

PC03*** / P2

UIF_BUTTON0 / UIF_LED0 / PB00 / P4

UIF_BUTTON1 / UIF_LED1 / PB01 / P6

NC / P8

NC / P10

PB02 / P12

DISP_EXTCOMIN / PA00 / P14

DBG_TCK_SWCLK / PA01 / P16

DBG_TMS_SWDIO / PA02 / P18

DBG_TDO_SWO / PA03 / P20

DBG_TDI* / PA04 / P22

NC / P24

NC / P26

NC / P28

NC / P30

NC / P32

NC / P34

GND

VMCU_IN

P1 / PC00 / DISP_MOSI

P3 / PC01**

P5 / PC02 / DISP_SCLK

P7 / PC03***

P9 / PA05 / VCOM_TX

P11 / PA06 / VCOM_RX

P13 / PB03

P15 / PB04 / VCOM_ENABLE

P17 / NC

P19 / PA07 / VCOM_RTS

P21 / PA08 / VCOM_CTS

P23 / NC

P25 / PC04 / PTI_DATA

P27 / PC05 / PTI_SYNC

P29 / PC06 / DISP_SCS

P31 / NC

P33 / NC

P35 / PD03 / DISP_ENABLE

VRF_IN

* Optional 0R resistor should be mounted to enable this connection. (Mutually exclusive with FLASH_SCS.)

** Mutually exclusive connection. Default: PC01 to P3.

*** Mutually exclusive connection. Default: PC03 to P7.

Figure 2.1. BRD4310A Radio Board Connector Pin Mapping

BRD4310A Reference Manual

Radio Board Block Summary

3. Radio Board Block Summary

3.1 Introduction

This section introduces the blocks of the BRD4310A Radio Board.

3.2 Radio Board Block Diagram

The block diagram of the BRD4310A Radio Board is shown in the figure below.

I2C

GPIO

UFL

Connector

UART

Debug

AEM

Radio

Board

Connectors

Packet Trace

SPI

xGM220S

EFR32

Module

RF In/Out

2.4 GHz RF

Path

Selection

Chip

Antenna

2.4 GHz RF

24AA0024

Serial EEPROM

8 Mbit

MX25R

Serial Flash

Crystal

Figure 3.1. BRD4310A Block Diagram

3.3 Radio Board Block Description

3.3.1 Wireless SiP

The BRD4310A Wireless Gecko Radio Board incorporates an BGM220SC12WGA2 Wireless Gecko module featuring 32-bit Cortex

M33 core, 352 kB of flash memory, 32 kB of RAM and a 2.4 GHz band transceiver with output power up to 0 dBm. For additional infor-

mation on the BGM220SC12WGA2, refer to the BGM220S data sheet.

3.3.2 LF Crystal Oscillator (LFXO)

The BRD4310A Radio Board has a 32.768 kHz crystal mounted. For details regarding the crystal configuration, refer to application note

AN0016.2: Oscillator Design Considerations.

3.3.3 UFL Connector

To perform conducted measurements, a UFL connector is added to the Radio Board. The connector allows an external 50 Ohm cable

or antenna to be connected during design verification or testing.

Note: By default, the 2.4 GHz RF input/output of the module is connected to the antenna input pin of the module by a series 0 Ohm

resistor. Connecting the RF input/output to the UFL connector supports conducted measurements, or the connection of an external an-

tenna. Move the series 0 Ohm resistor to the antenna to the position of the series resistor to the UFL connector (see the schematic of

the BRD4310A Radio Board for further details). On the layout, the footprints of these two resistors have overlapping pads to prevent

simultaneous connection of the antenna and the UFL connector.

| Building a more connected . 0.1 | 5

BRD4310A Reference Manual

Radio Board Block Summary

3.3.4 Radio Board Connectors

Two dual-row, 0.05” pitch polarized connectors make up the BRD4310A Radio Board interface to the Wireless Starter Kit Mainboard.

For more information on the pin mapping between the BGM220SC12WGA2 and the Radio Board Connector, refer to section 2.2 Radio

Board Connector Pin Associations.

3.3.5 Serial Flash

The BRD4310A Radio Board is equipped with an 8 Mbit Macronix MX25R SPI flash that is connected directly to the BGM220SC12 to

support over-the-air (OTA) updates. For additional information on the pin mapping, see the BRD4310A schematic.

3.3.6 Serial EEPROM

The BRD4310A Radio Board is equipped with a serial I

C EEPROM for board identification and to store additional board-related infor-

mation.

BRD4310A Reference Manual

Mechanical Details

4. Mechanical Details

The BRD4310A Radio Board is illustrated in the figures below.

UFL

Connector

XTAL

RF Output

Selection

xGM220S

Module

40 mm

OTA

Flash

22.7 mm

36.08 mm

41 mm

Figure 4.1. BRD4310A Top View

5 mm

24 mm

Board

Identification

PC03 to

Exp Header

Selection

PA04 to DBG_TDI

Selection

20 mm

PC01 to Exp

Header Selection

27.3 mm

28.6 mm

Interface

Connector

Interface

Connector

Figure 4.2. BRD4310A Bottom View

Rev. 0.1 | 7

BRD4310A Reference Manual

EMC Compliance

5. EMC Compliance

5.1 Introduction

Compliance of the fundamental and harmonic levels of the BRD4310A Radio Board is tested against the following standards:

•2.4 GHz:

•ETSI EN 300-328

•FCC 15.247

5.2 EMC Regulations for 2.4 GHz

5.2.1 ETSI EN 300-328 Emission Limits for the 2400-2483.5 MHz Band

Based on ETSI EN 300-328, the allowed maximum fundamental power for the 2400-2483.5 MHz band is 20 dBm EIRP. For the unwan-

ted emissions in the 1 GHz to 12.75 GHz domain, the specific limit is -30 dBm EIRP.

5.2.2 FCC15.247 Emission Limits for the 2400-2483.5 MHz Band

FCC 15.247 allows conducted output power up to 1 W (30 dBm) in the 2400-2483.5 MHz band. For spurious emissions, the limit is

-20 dBc based on either conducted or radiated measurement, if the emission is not in a restricted band. The restricted bands are speci-

fied in FCC 15.205. In these bands, the spurious emission levels must meet the levels set out in FCC 15.209. In the range from

960 MHz to the frequency of the 5th harmonic, it is defined as 0.5 mV/m at 3 m distance which equals to -41.2 dBm in EIRP.

If operating in the 2400-2483.5 MHz band, the 2nd, 3rd, and 5th harmonics can fall into restricted bands. As a result, for those harmon-

ics the -41.2 dBm limit should be applied. For the 4th harmonic the -20 dBc limit should be applied.

5.2.3 Applied Emission Limits for the 2.4 GHz Band

The above ETSI limits are applied both for conducted and radiated measurements.

The FCC restricted band limits are radiated limits only. In addition, Silicon Labs applies the same restrictions to the conducted spec-

trum. By doing so, compliance with the radiated limits can be estimated based on the conducted measurement, by assuming the use of

an antenna with 0 dB gain at the fundamental and the harmonic frequencies.

The overall applied limits are shown in the table below. For the harmonics that fall into the FCC restricted bands, the FCC 15.209 limit is

applied. ETSI EN 300-328 limit is applied for the rest.

Table 5.1. Applied Limits for Spurious Emissions for the 2.4 GHz Band

Harmonic

2nd

3rd

4th

5th

Frequency

4800~4967 MHz

7200~7450.5 MHz

9600~9934 MHz

12000~12417.5 MHz

Limit

-41.2 dBm

-30.0 dBm

-41.2 dBm

| Building a more connected . 0.1 | 8

BRD4310A Reference Manual

RF Performance

6. RF Performance

6.1 Conducted Power Measurements

During measurements, the BRD4310A Radio Board was attached to a Wireless Starter Kit Mainboard which was supplied by USB. The

voltage supply for the Radio Board was 3.3 V.

6.1.1 Conducted Power Measurements with Unmodulated Carrier

The transceiver was operated in unmodulated carrier transmission mode. The output power of the radio was set to 0 dBm. The typical

output spectrums are shown in the following figures.

Figure 6.1. Typical Output Spectrum of the BRD4310A; PAVDD = 3.3 V

As shown in the figure above, the fundamental is slightly lower than 0 dBm and all of the unwanted emissions are under the applied

limits.

Depending on the applied modulation scheme, the measured power levels are usually lower compared to the results with unmodulated

carrier, so the levels of the harmonics will be lower if modulated transmission is used.

Note: The conducted measurement is performed by connecting the on-board UFL connector to a Spectrum Analyzer through an SMA

Conversion Adapter (P/N: (40)). This connection itself introduces approximately 0.3 dB insertion loss.

Rev. 0.1 | 9

BRD4310A Reference Manual

RF Performance

6.2 Radiated Power Measurements

During measurements, the BRD4310A Radio Board was attached to a Wireless Starter Kit Mainboard which was supplied by USB. The

voltage supply for the Radio Board was 3.3 V. The radiated power was measured in an antenna chamber by rotating the board 360 de-

grees with horizontal and vertical reference antenna polarizations in the XY, XZ, and YZ cuts. The measurement planes are illustrated

in the figure below.

Figure 6.2. Illustration of Reference Planes with a Radio Board Plugged into the Wireless Starter Kit Mainboard

Note: The radiated measurement results presented in this document were recorded in an unlicensed antenna chamber. Also, the radi-

ated power levels may change depending on the actual application (PCB size, used antenna, and so on). Therefore, the absolute levels

and margins of the final application are recommended to be verified in a licensed EMC testhouse.

6.2.1 Radiated Measurements in the 2.4 GHz Band

The supply for the module (VDD) was 3.3 V provided by the mainboard; for details, see the BRD4310A schematic. The transceiver was

operated in continuous carrier transmission mode. The output power of the radio was set to 0 dBm based on the conducted measure-

ment.

The fundamental was set to the frequency where the maximum antenna gain was measured. The results are shown in the table below.

Note: The frequency in which the antenna gain has its maximum value can vary between modules due to the technological spreading

of the passive RF components and the antenna.

Table 6.1. Maximums of the Measured Radiated Powers in EIRP [dBm]

Frequency

Fund

2nd

3rd

4th

5th

EIRP [dBm]

0.3

<-50

Orientation

XY/H

-/-

Margin [dB]

29.2

>10

>20

>10

Limit in EIRP [dBm]

30.0

-41.2

-30.0

-41.2

* Signal level is below the Spectrum Analyzer noise floor.

As shown in the table above, due to the antenna gain, the fundamental is slightly higher than the output power based the conducted

measurement. The harmonics are below the Spectrum Analyzer noise floor.

6.2.2 Antenna Pattern Measurements

The measured normalized antenna patterns are shown in the following figures.

| Building a more connected . 0.1 | 10

BRD4310A Reference Manual

RF Performance

Normalized Radiation Pattern [dB], BRD4310A,

with WSTK, XY cut

-5

-10

-15

-20

-25

-30

-35

-40

-45

0°

Normalized Radiation Pattern [dB], BRD4310A,

with WSTK, XZ cut

-5

-10

-15

-20

-25

-30

-35

-40

-45

0°

Normalized Radiation Pattern [dB], BRD4310A,

with WSTK, YZ cut

-5

-10

-15

-20

-25

-30

-35

-40

-45

0°

315°45°315°45°315°45°

270°90°270°90°270°90°

225°135°

Horizontal

Vertical

225°135°

Horizontal

Vertical

225°135°

Horizontal

Vertical

180°180°180°

0°= X axis

0°= Z axis0°= Z axis

Figure 6.3. Normalized Antenna Pattern of the BRD4310A with the Wireless Starter Kit Mainboard

| Building a more connected . 0.1 | 11

BRD4310A Reference Manual

EMC Compliance Recommendations

7. EMC Compliance Recommendations

7.1 Recommendations for 2.4 GHz ETSI EN 300-328 Compliance

As shown in section 6. RF Performance, the power of the fundamental frequency of the BRD4310A Wireless Gecko Radio Board with

0 dBm output is compliant with the 20 dBm limit of the ETSI EN 300-328 regulation in both the conducted and radiated measurements.

The harmonic emissions are under the -30 dBm limit with large margin.

7.2 Recommendations for 2.4 GHz FCC 15.247 Compliance

As shown in section 6. RF Performance, the power of the fundamental frequency of the BRD4310A Wireless Gecko Radio Board with

0 dBm output is compliant with the 30 dBm limit of the FCC 15.247 regulation. The harmonic emissions are under the applied limits.

BRD4310A Reference Manual

Board Revision History

8. Board Revision History

The board revision is laser engraved in the Board Info field on the bottom side of the PCB, as outlined in the figure below. The revision

printed on the silkscreen is the PCB revision.

BRD4310A Rev. A02

123456789

Board

Revision

PCB

Revision

Figure 8.1. Revision Info

Table 8.1. BRD4310A Radio Board Revision History

Board Revision

A02

A01

A00

Description

Updated U1 OPN.

Updated X2 OPN. Removed ground isolation.

Initial production release.

| Building a more connected . 0.1 | 13

BRD4310A Reference Manual

Errata

9. Errata

There are no known errata at present.

BRD4310A Reference Manual

Document Revision History

10. Document Revision History

Revision 1.0

May, 2020

•Initial document release.

Simplicity Studio

One-click access to MCU and

wireless tools, documentation,

software, source code libraries &

more. Available for Windows,

Mac and Linux!

IoT Portfolio

/IoT

SW/HW

/simplicity

Quality

/quality

Support and Community

Disclaimer

Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or

intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"

parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes

without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information.

Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the

performance of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant

any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket

approval is required or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or

health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon

Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering

such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such

unauthorized applications.

Trademark Information

Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, ClockBuilder®, CMEMS®, DSPLL®, EFM®,

EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®,

Gecko®, Gecko OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri

DMS, Z-Wave®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings.

Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective

holders.

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA