2024年5月11日发(作者：奉子萱)
元器件交易网
Small Outline, 5 Lead, High
Speed Optocouplers
Technical Data
HCPL-M452
HCPL-M453
Features
• Surface Mountable
• Very Small, Low Profile
JEDEC Registered
Package Outline
• Compatible with Infrared
Vapor Phase Reflow and
Wave Soldering Processes
• Very High Common Mode
Transient Immunity:
15000 V/
µ
s at V
CM
= 1500 V
Guaranteed (HCPL-M453)
• High Speed: 1 Mb/s
• TTL Compatible
• Guaranteed AC and DC
Performance over
Temperature: 0
°
C to 70
°
C
• Open Collector Output
• Recognized Under the
Component Program of
U.L. (File No. E55361) for
Dielectric Withstand Proof
Test Voltage of 3750 Vac, 1
Minute
• Lead Free Option
Description
These small outline high CMR,
high speed, diode-transistor opto-
couplers are single channel
devices in a five lead miniature
footprint. They are electrically
equivalent to the following Agilent
optocouplers:
SO-5 Package
HCPL-M452
HCPL-M453
Standard DIP
HCPL-4502
HCPL-4503
SO-8 Package
HCPL-0452
HCPL-0453
(Note: These devices equivalent to 6N135/6N136 devices but without the base lead.)
The SO-5 JEDEC registered
(MO-155) package outline does
not require “through holes” in a
PCB. This package occupies
approximately one-fourth the
footprint area of the standard
dual-in-line package. The lead
profile is designed to be
compatible with standard
surface mount processes.
These diode-transistor
optocouplers use an insulating
layer between the light emitting
diode and an integrated photon
detector to provide electrical
insulation between input and
output. Separate connections for
the photodiode bias and output
transistor collector increase the
speed up to a hundred times
CAUTION: The small device geometries inherent to the design of this bipolar component increase the component's
susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken
in handling and assembly of this component to prevent damage and/or degradation which may be induced by
ESD.
元器件交易网
2
over that of a conventional
photo-transistor coupler by
reducing the base-collector
capacitance.
The HCPL-M452 is designed for
high speed TTL/TTL applica-
tions. A standard 16 mA TTL
sink current through the input
LED will provide enough output
current for 1 TTL load and a
5.6 kΩ pull-up resistor. CTR of
the HCPL-M452 is 19%
minimum at I
F
= 16 mA.
The HCPL-M453 is an HCPL-
M452 with increased common
mode transient immunity of
15,000 V/µs minimum at
V
CM
=1500 V guaranteed.
Outline Drawing (JEDEC MO-155)
Schematic
I
CC
6
V
CC
ANODE
1
4.4 ± 0.1
(0.173 ± 0.004)
6V
CC
MXXX
XXX
ANODE
7.0 ± 0.2
(0.276 ± 0.008)
CATHODE3
5V
OUT
4GND
+
1
V
F
I
F
CATHODE
–
3
SHIELD
I
O
5
V
O
4
0.4 ± 0.05
(0.016 ± 0.002)
3.6 ± 0.1*
(0.142 ± 0.004)
2.5 ± 0.1
(0.098 ± 0.004)
0.102 ± 0.102
(0.004 ± 0.004)
0.15 ± 0.025
(0.006 ± 0.001)
7° MAX.
1.27
BSC
(0.050)
0.71
MIN.
(0.028)
MAX. LEAD COPLANARITY
= 0.102 (0.004)
GND
DIMENSIONS IN MILLIMETERS (INCHES)
* MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
Applications
• Line Receivers -
High common mode transient
immunity (>1000V/µs) and
low input-output capacitance
(0.6 pF).
• High Speed Logic Ground
Isolation - TTL/TTL, TTL/
LTTL, TTL/CMOS, TTL/
LSTTL.
• Replace Slow Phototran-
sistor Optocouplers
• Replace Pulse
Transformers - Save board
space and weight
• Analog Signal Ground
Isolation -
Integrated photon detector
provides improved linearity
over phototransistor type.
Land Pattern Recommendation
4.4
(0.17)
2.5
(0.10)
1.3
(0.05)
2.0
(0.080)
8.27
(0.325)
0.64
(0.025)
DIMENSIONS IN MILLIMETERS AND (INCHES)
2024年5月11日发(作者：奉子萱)
元器件交易网
Small Outline, 5 Lead, High
Speed Optocouplers
Technical Data
HCPL-M452
HCPL-M453
Features
• Surface Mountable
• Very Small, Low Profile
JEDEC Registered
Package Outline
• Compatible with Infrared
Vapor Phase Reflow and
Wave Soldering Processes
• Very High Common Mode
Transient Immunity:
15000 V/
µ
s at V
CM
= 1500 V
Guaranteed (HCPL-M453)
• High Speed: 1 Mb/s
• TTL Compatible
• Guaranteed AC and DC
Performance over
Temperature: 0
°
C to 70
°
C
• Open Collector Output
• Recognized Under the
Component Program of
U.L. (File No. E55361) for
Dielectric Withstand Proof
Test Voltage of 3750 Vac, 1
Minute
• Lead Free Option
Description
These small outline high CMR,
high speed, diode-transistor opto-
couplers are single channel
devices in a five lead miniature
footprint. They are electrically
equivalent to the following Agilent
optocouplers:
SO-5 Package
HCPL-M452
HCPL-M453
Standard DIP
HCPL-4502
HCPL-4503
SO-8 Package
HCPL-0452
HCPL-0453
(Note: These devices equivalent to 6N135/6N136 devices but without the base lead.)
The SO-5 JEDEC registered
(MO-155) package outline does
not require “through holes” in a
PCB. This package occupies
approximately one-fourth the
footprint area of the standard
dual-in-line package. The lead
profile is designed to be
compatible with standard
surface mount processes.
These diode-transistor
optocouplers use an insulating
layer between the light emitting
diode and an integrated photon
detector to provide electrical
insulation between input and
output. Separate connections for
the photodiode bias and output
transistor collector increase the
speed up to a hundred times
CAUTION: The small device geometries inherent to the design of this bipolar component increase the component's
susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken
in handling and assembly of this component to prevent damage and/or degradation which may be induced by
ESD.
元器件交易网
2
over that of a conventional
photo-transistor coupler by
reducing the base-collector
capacitance.
The HCPL-M452 is designed for
high speed TTL/TTL applica-
tions. A standard 16 mA TTL
sink current through the input
LED will provide enough output
current for 1 TTL load and a
5.6 kΩ pull-up resistor. CTR of
the HCPL-M452 is 19%
minimum at I
F
= 16 mA.
The HCPL-M453 is an HCPL-
M452 with increased common
mode transient immunity of
15,000 V/µs minimum at
V
CM
=1500 V guaranteed.
Outline Drawing (JEDEC MO-155)
Schematic
I
CC
6
V
CC
ANODE
1
4.4 ± 0.1
(0.173 ± 0.004)
6V
CC
MXXX
XXX
ANODE
7.0 ± 0.2
(0.276 ± 0.008)
CATHODE3
5V
OUT
4GND
+
1
V
F
I
F
CATHODE
–
3
SHIELD
I
O
5
V
O
4
0.4 ± 0.05
(0.016 ± 0.002)
3.6 ± 0.1*
(0.142 ± 0.004)
2.5 ± 0.1
(0.098 ± 0.004)
0.102 ± 0.102
(0.004 ± 0.004)
0.15 ± 0.025
(0.006 ± 0.001)
7° MAX.
1.27
BSC
(0.050)
0.71
MIN.
(0.028)
MAX. LEAD COPLANARITY
= 0.102 (0.004)
GND
DIMENSIONS IN MILLIMETERS (INCHES)
* MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
Applications
• Line Receivers -
High common mode transient
immunity (>1000V/µs) and
low input-output capacitance
(0.6 pF).
• High Speed Logic Ground
Isolation - TTL/TTL, TTL/
LTTL, TTL/CMOS, TTL/
LSTTL.
• Replace Slow Phototran-
sistor Optocouplers
• Replace Pulse
Transformers - Save board
space and weight
• Analog Signal Ground
Isolation -
Integrated photon detector
provides improved linearity
over phototransistor type.
Land Pattern Recommendation
4.4
(0.17)
2.5
(0.10)
1.3
(0.05)
2.0
(0.080)
8.27
(0.325)
0.64
(0.025)
DIMENSIONS IN MILLIMETERS AND (INCHES)