2024年6月6日发(作者：务丝萝)
ASTM钢铁标准.F718
Designation:F718–99(Reapproved2005)An American National Standard Standard for
Shipbuilders and Marine Paints and Coatings Product/
Procedure Data Sheet1
This standard is issued under the?xed designation F718;the number immediately following the designation indicates the year of
original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A
superscript epsilon(e)indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1.1The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2provides on one sheet needed information concerning the characteristics of a speci?c paint or coating to include
generic description,physical properties, surface preparation requirements,application requirements, and front side of the sheet contains four major, numbered paragraphs and a highlighted
section for Special Safety paragraphs are as follows:
c Type and Description
cturers Data
ties
e Preparation Minimum Requirements
The back side of the page contains the following paragraphs: Procedure
ation.
1.2The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material,by production personnel to evaluate pro-duction compatibility of
proposed materials and to provide application instructions for selected paints and coatings mate-rials,and by quality control personnel to verify attributes of materials.
nced Documents
2.1ASTM Standards:3
D56Test Method for Flash Point by Tag Closed-Cup Tester D93Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D523Test Method for Specular Gloss
D1650Test Methods of Sampling and Testing Shellac Varnish4
D2697Test Method for V olume Nonvolatile Matter in Clear or Pigmented Coatings
D3278Test Method for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
A Method:5
nmental Protection Agency,40CFR Ch.1, Part60,Appendix A,Determination of V olatile Matter Content,Density,V olume Solids,and Weight Solids of Surface Coatings
ctions for Completing Data Sheet
3.1When?lling out the Product/Procedure Data Sheet(see Figs.1and2)remember that the information contained therein will be utilized by both technical and production personnel. Keep it simple and
brief but following instruc-tions are organized by paragraph numbers contained within the data see the two examples attached(Appendix X1).
3.2Paragraph I—Generic Type and Description—Use only known and industry-accepted generic Fig.1.
3.3Paragraph II—Manufacturers Data—This section is self-explanatory with the possible exception of subparagraph (f).This can be as complete or as brief as the concerned parties example,a
separate attached list of compatible and incompatible topcoats or acceptable cargo exposures could be Fig.1.
3.4Paragraph III—Properties—This section is also self-explanatory with the possible exception of subparagraph(a).If agreed upon by the concerned parties,a different method for determining volume
solids(theoretical coverage)may be form should be amended to show Fig.1.
3.5Special Safety Precautions—This section should con-tain speci?c instructions of what to do in the event of skin or eye contact or accidental ingestation,or nce should also be made to the
appropriate manufacturer’s Material Safety Data Fig.1.
1This standard is under the jurisdiction of ASTM Committee F25on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.01on Structures.
Current edition approved May1,hed ally approved /doc/ st previous edition approved in1999as F718–99.
2Copies of the data sheet are available at a nominal charge from ASTM Headquarters,100Barr Harbor Dr.,PO Box C700,West Conshohocken,PA t Adjunct 0718.
3For referenced ASTM standards,visit the ASTM website,/doc/ ,or
contact ASTM Customer Service at service@/doc/ .For Annual Book of ASTM Standards volume information,refer to the standard’s Document
Summary page on the ASTM website.
4Withdrawn.
5Available from /doc/ ernment Printing Office Superintendent of Documents, l St.,NW,Mail Stop:SDE,Washington,DC20401.
Copyright?ASTM International,100Barr Harbor Drive,PO Box C700,West Conshohocken,PA19428-2959,United States.
3.6Paragraph IV—Surface Preparation Minimum Require-ments :
3.6.1Subparagraphs (a)and (b)—Use an agreed-upon standard that is,ASTM,SSPC,Swedish,NACE,SNAME, Fig.1.
3.6.2Subparagraph (c)—Pro?le data are used,the pro?le listed must be given as a method of measurement must be agreed upon by all parties concerned,or this paragraph can be
left blank and the type and size of abrasive(s)allowed entered in subparagraph (d ),Special Fig.1. 3.7Paragraph V—Mixing Procedure —This section isself-explanatory with the
possible exceptions of subparagraphs (c )and (f ).Subparagraph (c )should preferably contain a generic solvent as opposed to a proprietary agraph (f )should,as a minimum,contain the mesh
size of the straining material and special procedures governing which component should be added to the agraph (b ),if appropriate,should include length of induction time given as a
function of various Fig.2.
3.8Paragraph VI—Application —This section is one of the most important of the entire must be ?lled
2024年6月6日发(作者：务丝萝)
ASTM钢铁标准.F718
Designation:F718–99(Reapproved2005)An American National Standard Standard for
Shipbuilders and Marine Paints and Coatings Product/
Procedure Data Sheet1
This standard is issued under the?xed designation F718;the number immediately following the designation indicates the year of
original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A
superscript epsilon(e)indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1.1The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2provides on one sheet needed information concerning the characteristics of a speci?c paint or coating to include
generic description,physical properties, surface preparation requirements,application requirements, and front side of the sheet contains four major, numbered paragraphs and a highlighted
section for Special Safety paragraphs are as follows:
c Type and Description
cturers Data
ties
e Preparation Minimum Requirements
The back side of the page contains the following paragraphs: Procedure
ation.
1.2The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material,by production personnel to evaluate pro-duction compatibility of
proposed materials and to provide application instructions for selected paints and coatings mate-rials,and by quality control personnel to verify attributes of materials.
nced Documents
2.1ASTM Standards:3
D56Test Method for Flash Point by Tag Closed-Cup Tester D93Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D523Test Method for Specular Gloss
D1650Test Methods of Sampling and Testing Shellac Varnish4
D2697Test Method for V olume Nonvolatile Matter in Clear or Pigmented Coatings
D3278Test Method for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
A Method:5
nmental Protection Agency,40CFR Ch.1, Part60,Appendix A,Determination of V olatile Matter Content,Density,V olume Solids,and Weight Solids of Surface Coatings
ctions for Completing Data Sheet
3.1When?lling out the Product/Procedure Data Sheet(see Figs.1and2)remember that the information contained therein will be utilized by both technical and production personnel. Keep it simple and
brief but following instruc-tions are organized by paragraph numbers contained within the data see the two examples attached(Appendix X1).
3.2Paragraph I—Generic Type and Description—Use only known and industry-accepted generic Fig.1.
3.3Paragraph II—Manufacturers Data—This section is self-explanatory with the possible exception of subparagraph (f).This can be as complete or as brief as the concerned parties example,a
separate attached list of compatible and incompatible topcoats or acceptable cargo exposures could be Fig.1.
3.4Paragraph III—Properties—This section is also self-explanatory with the possible exception of subparagraph(a).If agreed upon by the concerned parties,a different method for determining volume
solids(theoretical coverage)may be form should be amended to show Fig.1.
3.5Special Safety Precautions—This section should con-tain speci?c instructions of what to do in the event of skin or eye contact or accidental ingestation,or nce should also be made to the
appropriate manufacturer’s Material Safety Data Fig.1.
1This standard is under the jurisdiction of ASTM Committee F25on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.01on Structures.
Current edition approved May1,hed ally approved /doc/ st previous edition approved in1999as F718–99.
2Copies of the data sheet are available at a nominal charge from ASTM Headquarters,100Barr Harbor Dr.,PO Box C700,West Conshohocken,PA t Adjunct 0718.
3For referenced ASTM standards,visit the ASTM website,/doc/ ,or
contact ASTM Customer Service at service@/doc/ .For Annual Book of ASTM Standards volume information,refer to the standard’s Document
Summary page on the ASTM website.
4Withdrawn.
5Available from /doc/ ernment Printing Office Superintendent of Documents, l St.,NW,Mail Stop:SDE,Washington,DC20401.
Copyright?ASTM International,100Barr Harbor Drive,PO Box C700,West Conshohocken,PA19428-2959,United States.
3.6Paragraph IV—Surface Preparation Minimum Require-ments :
3.6.1Subparagraphs (a)and (b)—Use an agreed-upon standard that is,ASTM,SSPC,Swedish,NACE,SNAME, Fig.1.
3.6.2Subparagraph (c)—Pro?le data are used,the pro?le listed must be given as a method of measurement must be agreed upon by all parties concerned,or this paragraph can be
left blank and the type and size of abrasive(s)allowed entered in subparagraph (d ),Special Fig.1. 3.7Paragraph V—Mixing Procedure —This section isself-explanatory with the
possible exceptions of subparagraphs (c )and (f ).Subparagraph (c )should preferably contain a generic solvent as opposed to a proprietary agraph (f )should,as a minimum,contain the mesh
size of the straining material and special procedures governing which component should be added to the agraph (b ),if appropriate,should include length of induction time given as a
function of various Fig.2.
3.8Paragraph VI—Application —This section is one of the most important of the entire must be ?lled