2024年10月28日发(作者：辉羽彤)
3
IC200PWR101
120/240VAC Power Supply
120/240VAC Power Supply IC200PWR101 provides backplane power for CPU, NIU, and
I/O modules. It supplies up to 1.5 Amps output current via 3.3 Volt and 5 Volt outputs,
with up to 0.25 Amp on the 3.3 volt output. This is ample power for most installations.
Module backplane current consumption is summarized in appendix C.
120/240 VAC, 27VA
POWER SUPPLY
WARNING:
EXPLOSION HAZARD
WHEN IN HAZARDOUS
LOCATIONS TURN OFF
POWER BEFORE
REPLACING OR WIRING
MODULES.
IND CONT EQ FOR HAZ LOC
CLASS I DIV 2
GROUPS ABCD
Temp Code T4A
Ambient 60C
MADE IN USA
IC200PWR101
ADD JUMPER
FOR 120V
LN
INPUT
VAC
When mounted on the CPU or NIU module, this power supply serves as the main power
supply for the station. It can also be used as a supplemental power supply when mounted
on a Power Supply Booster Carrier. Refer to the Power Supply Booster Carrier section of
chapter 4 for more information.
3-6VersaMax® Modules, Power Supplies, and Carriers User's Manual – March 2003 GFK-1504K
3
IC200PWR101
120/240VAC Power Supply
Specifications
Input Voltage
I
nput Power
F
requency
Holdup Time
Output Voltage
Protection
Output Current
Total
3.3VDC Output
5VDC Output
85 to 132 VAC with jumper installed, 120VAC nominal
176 to 264 VAC w/o jumper installed, 240VAC nominal
2
7VA
4
7 to 63Hz
20ms
5VDC, 3.3 VDC
Short circuit, overload
1.5A maximum
z
0.25A maximum
(1.5A - I
3.3V
) maximum
•
mple,************
is required, 1.25A is available on the 5V output.
Jumper Selection of 120VAC or 240VAC
This power supply can be used with either 120VAC or 240VAC nominal input power. For
120VAC nominal operation, a jumper should be installed as marked on the power supply.
JUMPER
FOR 120V
The power supply operates without a jumper installed; however, the hold-up specification
is not met. If a jumper is not installed for 120VAC operation, the power supply will not
cause hazardous conditions.
WARNING:
DO NOT USE A JUMPER FOR 240VAC OPERATION. If a jumper is used on the
input connector for 240VAC nominal operation, the power supply will be damaged
and may cause hazardous conditions.
GFK-1504K Chapter 3 Power Supplies3-7
2024年10月28日发(作者：辉羽彤)
3
IC200PWR101
120/240VAC Power Supply
120/240VAC Power Supply IC200PWR101 provides backplane power for CPU, NIU, and
I/O modules. It supplies up to 1.5 Amps output current via 3.3 Volt and 5 Volt outputs,
with up to 0.25 Amp on the 3.3 volt output. This is ample power for most installations.
Module backplane current consumption is summarized in appendix C.
120/240 VAC, 27VA
POWER SUPPLY
WARNING:
EXPLOSION HAZARD
WHEN IN HAZARDOUS
LOCATIONS TURN OFF
POWER BEFORE
REPLACING OR WIRING
MODULES.
IND CONT EQ FOR HAZ LOC
CLASS I DIV 2
GROUPS ABCD
Temp Code T4A
Ambient 60C
MADE IN USA
IC200PWR101
ADD JUMPER
FOR 120V
LN
INPUT
VAC
When mounted on the CPU or NIU module, this power supply serves as the main power
supply for the station. It can also be used as a supplemental power supply when mounted
on a Power Supply Booster Carrier. Refer to the Power Supply Booster Carrier section of
chapter 4 for more information.
3-6VersaMax® Modules, Power Supplies, and Carriers User's Manual – March 2003 GFK-1504K
3
IC200PWR101
120/240VAC Power Supply
Specifications
Input Voltage
I
nput Power
F
requency
Holdup Time
Output Voltage
Protection
Output Current
Total
3.3VDC Output
5VDC Output
85 to 132 VAC with jumper installed, 120VAC nominal
176 to 264 VAC w/o jumper installed, 240VAC nominal
2
7VA
4
7 to 63Hz
20ms
5VDC, 3.3 VDC
Short circuit, overload
1.5A maximum
z
0.25A maximum
(1.5A - I
3.3V
) maximum
•
mple,************
is required, 1.25A is available on the 5V output.
Jumper Selection of 120VAC or 240VAC
This power supply can be used with either 120VAC or 240VAC nominal input power. For
120VAC nominal operation, a jumper should be installed as marked on the power supply.
JUMPER
FOR 120V
The power supply operates without a jumper installed; however, the hold-up specification
is not met. If a jumper is not installed for 120VAC operation, the power supply will not
cause hazardous conditions.
WARNING:
DO NOT USE A JUMPER FOR 240VAC OPERATION. If a jumper is used on the
input connector for 240VAC nominal operation, the power supply will be damaged
and may cause hazardous conditions.
GFK-1504K Chapter 3 Power Supplies3-7