2024年5月21日发(作者：旁念)

Manual Supplement

Manual Title: 5320A Users

Print Date: September 2006

Revision/Date:

Supplement Issue: 2

Issue Date: 11/06

3

Page Count:

This supplement contains information necessary to ensure the accuracy of the

above manual. This manual is distributed as an electronic manual on the

following CD-ROM:

CD Title: 5320A

CD Rev. & Date: 9/2006

PCD N: 2634346

© 2006 Fluke Corporation. All rights reserved. Printed in U.S.A.

x

5320A Users Manual Supplement

Change #1

On page 7-26, replace Figure 7-23 with the following:

Quadtech Sentry

Fluke 5320A

FrontBack

Fluke 5320A kV Divider/R Multiplier

Figure 7-23. 10 kV High Voltage Adapter Application

Change #2

On page 5-15, change the following:

From:

OUTPute[:STATus](?){ON/OFF}

OUTPut[:STATe](?){ON/OFF}

To:

10/06 1

Manual Supplement 5320A Users

Change #3

On page 5-25, change the following:

From: [SOUR]:SAF:IDP[:CURR]:RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Passive Leakage Current

function.

Query:

To:

SAF:IDP:RES? Returns the value of the instantaneous current flowing

through the Calibrator.

[SOUR]:SAF:IDP[:CURR]:RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Passive Leakage Current

function.

Query: SAF:IDP:RES? Returns the value of the resulting measured UUT

current.

On page 5-26, change the following:

From: [SOUR]:SAF:IDD[:CURR]: RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Differential Leakage

Current function.

Query:

To:

SAF:IDD:RES? Returns the value of the instantaneous current flowing

through the Calibrator.

[SOUR]:SAF:IDD[:CURR]: RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Differential Leakage

Current function.

Query: SAF:IDD:RES? Returns the value of the resulting measured UUT

current.

Change #4

On page 6-6, after step 2 of High Resistance Source Verification, add the following note:

Note

For some megohmmeters, when using the Calibrator’s 100 G

Ω

value or when using the

resistance multiplier adapter, the leads must be swapped between the Calibrator’s HI

and LO ohms resistance output. The ground must be turned on (GDN ON) when

swapping HI and LO lead positions in the high ohms resistance function. For example to

make a proper measurement with the Quadtech 1865 megohmmeter, connect the HI

terminal on the megohmmeter to the LO terminal on the Calibrator and connect the LO

terminal on the megohmmeter to the HI terminal on the Calibrator. Turn the ground on

and proceed to make the measurement.

2 10/06

5320A Users Manual Supplement

Change #5

On page 1-8, delete the following from the Table:

Plug adapter (x2) 2743474

11/06 3

2024年5月21日发(作者：旁念)

Manual Supplement

Manual Title: 5320A Users

Print Date: September 2006

Revision/Date:

Supplement Issue: 2

Issue Date: 11/06

3

Page Count:

This supplement contains information necessary to ensure the accuracy of the

above manual. This manual is distributed as an electronic manual on the

following CD-ROM:

CD Title: 5320A

CD Rev. & Date: 9/2006

PCD N: 2634346

© 2006 Fluke Corporation. All rights reserved. Printed in U.S.A.

x

5320A Users Manual Supplement

Change #1

On page 7-26, replace Figure 7-23 with the following:

Quadtech Sentry

Fluke 5320A

FrontBack

Fluke 5320A kV Divider/R Multiplier

Figure 7-23. 10 kV High Voltage Adapter Application

Change #2

On page 5-15, change the following:

From:

OUTPute[:STATus](?){ON/OFF}

OUTPut[:STATe](?){ON/OFF}

To:

10/06 1

Manual Supplement 5320A Users

Change #3

On page 5-25, change the following:

From: [SOUR]:SAF:IDP[:CURR]:RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Passive Leakage Current

function.

Query:

To:

SAF:IDP:RES? Returns the value of the instantaneous current flowing

through the Calibrator.

[SOUR]:SAF:IDP[:CURR]:RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Passive Leakage Current

function.

Query: SAF:IDP:RES? Returns the value of the resulting measured UUT

current.

On page 5-26, change the following:

From: [SOUR]:SAF:IDD[:CURR]: RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Differential Leakage

Current function.

Query:

To:

SAF:IDD:RES? Returns the value of the instantaneous current flowing

through the Calibrator.

[SOUR]:SAF:IDD[:CURR]: RES?

Description: This command returns the measured current flowing through the UUT. If not

already selected, it also switches the Calibrator to the Differential Leakage

Current function.

Query: SAF:IDD:RES? Returns the value of the resulting measured UUT

current.

Change #4

On page 6-6, after step 2 of High Resistance Source Verification, add the following note:

Note

For some megohmmeters, when using the Calibrator’s 100 G

Ω

value or when using the

resistance multiplier adapter, the leads must be swapped between the Calibrator’s HI

and LO ohms resistance output. The ground must be turned on (GDN ON) when

swapping HI and LO lead positions in the high ohms resistance function. For example to

make a proper measurement with the Quadtech 1865 megohmmeter, connect the HI

terminal on the megohmmeter to the LO terminal on the Calibrator and connect the LO

terminal on the megohmmeter to the HI terminal on the Calibrator. Turn the ground on

and proceed to make the measurement.

2 10/06

5320A Users Manual Supplement

Change #5

On page 1-8, delete the following from the Table:

Plug adapter (x2) 2743474

11/06 3