AOC空气净化器使用说明书-USB迷|专注于互联网分享

2024年8月5日发(作者：容信厚)

MODEL PART DIAGRAM

FRONT

BACK

Control Panel

Handle

Air Outlet

Front Panel

Vent

PACKAGE CONTENTS

Power Plug

Unit

(1) Pre-Filter

(1) Washable AOC™ Carbon Filter

Remote

User

(1) True HEPA Filter

Control

Manual

Remote Control and User Manual will be

located on the top insert after the box is opened.

WHERE TO USE

Allow 12 ~ 18 in. of space between TVs, radios, and other

electronics

Electromagnetic interference from certain electronics may

cause product malfunction.

Place indoors away from direct sunlight

Direct exposure may cause product malfunction or failure.

12~18 in

Only place on hard, flat surfaces

12~18 in

Flimsy or slanted surfaces may result in abnormal noise and

vibrations.

Allow at least 12 ~ 18 in. from walls for maximum air flow

4-STAGE AIR PURIFICATION

Air Purification means it

removes inanimate particles

Pre-Filter

Washable AOC™ Carbon Filter

True HEPA Filter

PlasmaWave

REMOTE CONTROL

Operates in a 20 foot radius:

•

or off.

(A) Power: Turns the unit on

WARNING

•

(B) Auto: Enables Auto Mode.

• (C) Fan Speed

• Incorrect battery usage may cause battery

manual operation of the fan

: Enables

fluid leakage and/or damage.

• When not using remote for extended periods

speeds.

• (D) Turbo

of time, remove the battery.

Mode and directly sets the

: Enters Manual

• Avoid dropping or damaging the remote.

fan speed to Turbo.

• WARNING: Chemical Burn Hazard. Keep

batteries away from children.

How to replace your remote’s battery:

• This product contains a lithium button/coin

1. Flip over your remote and

cell battery. If a new or used lithium button/

coin cell battery is swallowed or enters the

1.A

open battery tray.

• 1.A

body, it can cause severe internal burns and

1.B

while,

: Pinch the lever in

can lead to death in as little as 2 hours.

• 1.B

• Always completely secure the battery

compartment.

2.A

tray out.

: Pulling the battery

2. Insert battery into the

• If the battery compartment does not close

battery tray as shown.

securely, stop using the product, remove the

• 2.A

batteries, and keep it away from children.

• If you think batteries might have been

3.A

polarities [+] [-] match

: Make sure the

when placing in the tray.

swallowed or placed inside any part of the

body, seek immediate medical attention.

3. Close the battery tray.

• The batteries should be disposed of

• 3.A

properly, including keeping them away from

tray into remote until

: Reinsert battery

children. Even used batteries may cause

you hear a "click" sound.

injury.

Keep all used batteries (CR2025) in safe place.

INITIAL OPERATION

1. Remove the front panel by grasping its upper

edge and gently pulling forward.

Latch

2. Remove the Pre-Filter, then the plastic bag

of filters behind it.

3. Remove filters from protective plastic bag.

4. Install the filters until they fit securely in

place.

03. True HEPA Filter (back)

02. Washable AOC™ Carbon Filter (middle)

01. Pre-Filter (front)

5. After filters are installed, close the front

Latch

panel.

6. Insert the power cord into an electrical

outlet.

CONTROL PANEL

0102

04050607

091011

131415

01. Auto Indicator

Indicates whether Auto Mode is enabled or

• Auto Mode:

disabled.

- Auto Mode automatically adjusts fan speeds

according to your indoor air quality. The fan

02. Sleep Indicator

speed will adjust to low when air quality is

Indicates whether Sleep Mode is enabled or

good, medium when fair, and to high when

disabled.

poor.

03. PlasmaWave

• Sleep Mode:

Indicates whether PlasmaWave

Indicator

- Fan speed will automatically set to minimum

disabled.

is enabled or

speed (lower than 'Low') which will be nearly

silent.

04. Fan Speed Indicator

- When Sleep Mode is active, PlasmaWave

Indicates the current fan speed.

will be disabled, but it can be turned back on.

05. Timer Indicator

11. PlasmaWave

If timer has been set, the LED light indicates the

Enables or disables PlasmaWave

Button

set time of operation.

"When the unit is running, you may hear a chirping

06. Filter Replacement Indicator

or buzzing sound. The sound is from large

LED light indicates when it is time to change the

particles passing through PlasmaWave

filter.

normal and does not signify product failure."

, it is

Press the PlasmaWave

07. Light Sensor

to enable or disable this feature.

button when the unit is on

Detects the amount of ambient light in the

environment.

12. Air Quality Indicator

Color coded LED light indicates one of three levels

08. Smart Sensor

of Air Quality: Red (poor), Amber (fair), and Blue

Detects the amount of odorous gas in the

(good).

environment. When in Auto mode, the fan speed

adjusts according to the detected amount of gas.

13. Fan Speed Button

Enables manual operation of the unit's fan speeds.

09. Power Button

• Press to cycle through and set the desired fan

Turns the unit on or off.

speed (Low, Medium, High, Turbo).

During the first 30 seconds of powering up, the

Air Quality Indicator will cycle through Blue,

14. Timer Button

Amber and Red colors. Smart Sensor takes

Press to cycle through and set desired length of

approximately 4minutes to detect the air quality in

operation (1hr, 4hr, 8hr, [NO TIMER]).

the environment before normal operation begins.

15. Filter Reset Button

10. Mode Button

After replacing the filter, turn on the unit and then

Press to cycle through to set the mode of operation

use a thin object, such as a paper clip, to press the

(Auto, Sleep). The unit will default to Auto with

Filter Reset Button for 5 seconds.

PlasmaWave

enabled when first powered on.

MAINTENANCE

When to Replace Filters

FilterIndicator LightWhen to ServiceWhen to Replace

Pre-FilternoneClean once every 14 daysPermanent

Washable AOC™ Carbon Filter* Clean once every 3 months

True HEPA FilterCan NOT be WASHED

Last Approx. 12 months

• When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and Washable

AOC™ Carbon Filter.

• Intervals between filter replacement may vary depending on environment.

* Filter performance may decrease after each wash and depending on contamination level prior to washing.

REPLACING FILTERS

Resetting Filter Life:

After replacing your True HEPA Filter, place the Pre-Filter

back in and close the Front Panel. While the unit is on, hold

the Filter Reset Button for at least 5 seconds until you hear

the beep. After the beep, the Filter Replacement Indicator

CLEANING CARE

will disappear. Your Winix True HEPA is now reset.

Cleaning the Filters:Cleaning the Exterior & Interior:

Use a vacuum cleaner or soft brush to clean the

Pre-Filter

1. Open the front panel and clean the interior

• If it is excessively soiled, rinse in room

with a vacuum cleaner.

• A hand vacuum or hose attachment will work

•

temperature .

•

Do not use detergent or soap.

Allow the filter to dry for 24 hours or more before

2. Dampen a cloth with room temperature water and

using.

wipe down the interior and exterior of the unit.

• Intervals between filter cleaning may vary

3. Wipe the unit down with a clean, dry cloth.

• Ensure no moisture remains before plugging

To clean the Washable AOC™ Carbon Filter, remove

depending on the air quality in the environment.

from unit and rinse under lightly running room

* For optimal performance, clean every 1 - 2 months.

the unit back in.

temperature water.

• Do not use detergent or soap. Allow the filter to

dry for 24 hours or mote before using. Do not use

hot water over 104°F.

NOTICE

•Never disassemble, repair, or modify the unit yourself.

• When cleaning the unit, always unplug the

•

power cord first and then wait until the unit

•

Do not use flammable sprays or liquid detergents.

has cooled down.

•

Do not allow children to clean or maintain the unit.

Before cleaning or maintaining, ensure unit is

unplugged.

SAFETY AND CAUTIONS

Before operating this equipment, carefully read and

follow these safety cautions.

WARNING

Ensure filters are inserted before running unit.

Running the unit without filters can shorten the

Follow these instructions to reduce the risk of

lifespan of the unit and cause electric shock or

serious injury or death and to reduce risk of

injury.

damaging the unit.

Be sure foreign objects are NOT inserted into the

vents on the unit.

• If the power cord is damaged, it must be replaced

Objects can include pins, rods, and coins.

by a special cord. Reassembly is available from

the manufacturer or its service agent.

Do not touch any part of the interior of the unit

with wet hands.

• This appliance is not intended for use by

a person (including children) with reduced

The high voltage may cause electric shock.

physical, sensory or mental capabilities, or lack

Ensure unit intake and outlet vents do not become

of experience and knowledge of the unit, unless

blocked.

they have been given supervision or instruction

Blockage may lead to increased internal

concerning use of the appliance by a person

termperatures causing product failure and

responsible for their safety.

deformation.

• Children should be supervised to ensure that

Do not use the unit as a step stool or place heavy

they do not play with the appliance.

objects on the unit.

• This unit is not intended to be used to preserve

Personal injury may occur or product failure and

documents or art conservation.

deformation.

Do not pull on the power cord when

unplugging the unit.

The cord can become damaged by

forcefully bending, pulling, twisting,

Do not tie or knot the power cord when unit

bundling, pinching or placing heavy objects

is in operation.

on it.

If the unit becomes submerged in water,

Do not install in any sort of motor or

unplug it and contact customer service.

transport vehicle (trucks, boats, ships,

etc.).

Do not unplug or move the unit while in

operation.

Do not place in an area with excessive

amounts of noxious gases.

Do not plug additional appliances into the

same outlet or power supply.

Do not place near any flammable materials

(aerosols, fuel, gases, etc.).

Do not touch the plug with wet hands.

Do not have the unit facing into wind or

Unplug the unit when not in operation for

drafts.

extended periods of time.

Do not place below any electrical outlet.

Do not place around heating elements.

Do not place in excessively humid areas

Do not use around mist or fumes from

where the unit may become wet.

industrial oil or around large quantities of

metallic dust.

Do not place unit closer than 12 inches

from the wall during operation. It may

cause condensation on the wall and the

surrounding area.

TWO YEARS WARRANTY

The terms of the warranty are as follows:

1. This product is manufactured under stringent

Product Name

Air Purifier

quality control and inspections.

Model Name

5500-2

2. The warranty will be voided if product failure

Purchase Date

is a result of negligence or misuse by the

consumer.

Warranty Period

Two (2) Years

3. A proof of purchase must be presented upon

Place of Purchase

claiming a Product Warranty.

Place of Purchase

4. Store the proof of purchase in a safe place or

tel.

upload your proof of purchase.

Address

5. This warranty is valid only in the USA and

Customer

Name

Canada.

* f

Tel.

/terms-and-conditions/

or more information visit

After purchase, be sure to complete all of the

above information.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science

and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following

two conditions:

• This device may not cause interference.

• This device must accept any interference, including interference that may cause undesired operation

of the device.

"In French: Cet appareil contient des émetteurs/récepteurs exemptés de licence et conformes

aux normes Innovation, Science et Economic. RSS(s) sans licence de Développement Canada. Le

fonctionnement est soumis aux deux conditions suivantes:

• cet appareil ne doit pas causer d’interférences nuisibles, et

• cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un

fonctionnement non souhaité."

2610-0314-00 Rev.01

SAFETY INSTRUCTIONS

Thank you for purchasing a Winix air purifier. This product is for household use only.

IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER:

WARNING:

Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire.

• Do not repair or modify the unit yourself.• If the power plug is damaged, it must be replaced

• All repairs should be completed by a qualified

by the manufacturer or a qualified technician.

Winix technician.• Remove the power plug from the outlet when not

• The plug for this unit is polarized with one blade

in use.

wider than the other. Do not force the plug into

an electrical outlet. Do not alter the plug in

• Do not handle the power plug with wet hands.

any way. If the plug does not fit into the outlet,

• Do not operate the unit when using indoor

reverse the plug. If it still does not fit, contact a

smokegenerating insecticides.

qualified technician to install a proper outlet.

• Do not clean unit with benzene or paint thinner.

• Do not use if the power cord or plug is damaged

Do not spray insecticides on the unit.

or the connection to the wall outlet is loose.

• Do not use the unit where it is humid or where

• Use AC 120 V only.

the unit may become wet, such as the bathroom.

• Do not damage, break, forcefully bend, pull, twist,

• Do not insert fingers or foreign objects into air

bundle, coat, pinch, or place heavy objects on

intake or outlet.

the power cord.

• Do not use the unit near flammable gases. Do

• Periodically remove dust from the power plug.

not use near cigarettes, incense, or other spark-

This will reduce the risk of shock due to humidity

creating items.

build up.

• Unit will not remove carbon monoxide emitted

• Remove the power plug from the outlet before

from heating appliances or other sources.

cleaning the unit. When removing the power

• Unplugging the product disconnects the remote

plug, grasp by holding the plug itself, never hold

functions.

by the cord.

IMPORTANT PRECAUTIONS FOR USING YOUR AIR PURIFIER:

• Do not block the intake or outlet vents.

• Do not use near hot objects, such as a stove.

• Do not use where the unit may come into contact with steam.

• Do not use the unit on its side.

• Keep away from products that generate oily residue, such as a deep fryer.

• Do not use detergent to clean the unit.

• Do not operate without a filter.

• Do not wash and reuse the True HEPA Filter.

• Hold the handle on the back of the unit to transport.

• Do not hold by the front panel.

• Do not stick any small objects into the air outlet vents or fan.

BATTERY IN REMOTE CONTROL:

• This product contains a button battery.

If swallowed, it could cause severe injury or death in just two hours. Seek medical attention

immediately.

• "In French: Cet article contient une pile bouton. De graves blessures ou la mort pourraient suivre dans

les deux heures suivant I'ingestion. Demander I'aide de professionnels de la santé sur le champ."

AIR PURIFIER

5500-2 USER MANUAL

UNIT SPECIFICATIONS

Model Name5500-2Dimensions15 in(W) × 8.2 in(D) × 23.6 in(H)

Power VoltageAC 120 V / 60 HzWeight15 lbs

Power Rate

70 W

Replacement

Verified Room Size360 .

Filter

Filter H / SKU: 116130

The exterior, design, and product specifications may be changed without prior notice to improve product performance.

Contact Winix for

product related inquiries

and customer service

• Dedicated Call Center:

☎

(877) 699-4649

The energy efﬁciency of this ENERGY STAR

• Website:

certiﬁed model is measured based on a ratio

To expedite service, please specify the

between the model’s CADR for smoke and the

model name and number, the nature of the

electrical energy it consumes, or CADR/Watt.

problem, your contact information, and

your address.