2024年10月30日发(作者：广盼盼)

Technical manual

Mounting Instructions

BR5010

CHARACTERISTICS

The Bravo is a top reading electronic entry unit that provides easy operation for under-desk

safes as well as spy protection. The numbers can only be read up close by the operator. The

code numbers will not be “spied on” from a distance. The entry unit features a terminal for an

electronic key and/or audit. The integrated battery compartment in the bottom of the Bravo

entry unit opens by moving a slider. Cable length is approximately 30 cm. The Bravo entry

can be mounted as stationary or turnable model.

DIMENSIONS / MOUNTING INSTRUCTIONS

The terminal for the electronic key (Dallas Key) and or communication is located on the front

next to the LED. In case this terminal is not required, it should be covered with the provided

round black label.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

1

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878

STATIONARY MOUNTING:

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must

be de-burred well to avoid damage to the cable.

Prepare the mounting and cable holes according to picture

Hold the bearing plate in a way against the mounting surface that

“UP” is readable on top. Affix the plate with the two mounting

adapter screws (M4) hand tied.

Insert first the spring and then the pin into the hole on the back

cover

Route the cable through the cable hole, hold the unit at the

(approximately) 10:00 o’clock position and slide it on the

mounting adapters.

Turn unit clockwise until it clicks into a stationary position at

12:00.

The Bravo entry unit can now not be removed after installation!

Connect one (1) battery to the battery clip. Only use 9V ALKALINE Duracell/ Procell- or

Energizer batteries.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

2

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878

As TURNABLE ENTRY UNIT with M- LOCKS StraightBolt lock EM3520:

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must

be de-burred well to avoid damage to the cable. Cut the grooved shaft to the appropriate

length: Measure door thickness (from mounting surface of the entry unit to the mounting

surface of the lock) and add 41,5 mm (1.6”).

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

Prepare the mounting and cable holes according to picture

Hold the bearing plate in a way against the mounting surface that

“UP ROTATE” is readable on top. Affix the plate with the two

mounting adapter screws (M4) hand tied.

Insert first the spring and then the pin into the hole on the back cover

Insert the grooved shaft all the way into the entry housing

Tel: +31 (0)314 376 876

ver. 1.1 2010 07 19 Fax: +31 (0)314 376 878

3

Route the cable through the cable hole, hold the unit at the

(approximately) 10:00 o’clock position and slide it on the mounting

adapters.

Turn unit clockwise until it clicks into a stationary position at 12:00.

The Bravo entry unit will not be detachable once the lock is installed.

Connect one (1) battery to the battery clip. Only use 9V ALKALINE Duracell/ Procell- or

Energizer batteries.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

4

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878

2024年10月30日发(作者：广盼盼)

Technical manual

Mounting Instructions

BR5010

CHARACTERISTICS

The Bravo is a top reading electronic entry unit that provides easy operation for under-desk

safes as well as spy protection. The numbers can only be read up close by the operator. The

code numbers will not be “spied on” from a distance. The entry unit features a terminal for an

electronic key and/or audit. The integrated battery compartment in the bottom of the Bravo

entry unit opens by moving a slider. Cable length is approximately 30 cm. The Bravo entry

can be mounted as stationary or turnable model.

DIMENSIONS / MOUNTING INSTRUCTIONS

The terminal for the electronic key (Dallas Key) and or communication is located on the front

next to the LED. In case this terminal is not required, it should be covered with the provided

round black label.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

1

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878

STATIONARY MOUNTING:

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must

be de-burred well to avoid damage to the cable.

Prepare the mounting and cable holes according to picture

Hold the bearing plate in a way against the mounting surface that

“UP” is readable on top. Affix the plate with the two mounting

adapter screws (M4) hand tied.

Insert first the spring and then the pin into the hole on the back

cover

Route the cable through the cable hole, hold the unit at the

(approximately) 10:00 o’clock position and slide it on the

mounting adapters.

Turn unit clockwise until it clicks into a stationary position at

12:00.

The Bravo entry unit can now not be removed after installation!

Connect one (1) battery to the battery clip. Only use 9V ALKALINE Duracell/ Procell- or

Energizer batteries.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

2

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878

As TURNABLE ENTRY UNIT with M- LOCKS StraightBolt lock EM3520:

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must

be de-burred well to avoid damage to the cable. Cut the grooved shaft to the appropriate

length: Measure door thickness (from mounting surface of the entry unit to the mounting

surface of the lock) and add 41,5 mm (1.6”).

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

Prepare the mounting and cable holes according to picture

Hold the bearing plate in a way against the mounting surface that

“UP ROTATE” is readable on top. Affix the plate with the two

mounting adapter screws (M4) hand tied.

Insert first the spring and then the pin into the hole on the back cover

Insert the grooved shaft all the way into the entry housing

Tel: +31 (0)314 376 876

ver. 1.1 2010 07 19 Fax: +31 (0)314 376 878

3

Route the cable through the cable hole, hold the unit at the

(approximately) 10:00 o’clock position and slide it on the mounting

adapters.

Turn unit clockwise until it clicks into a stationary position at 12:00.

The Bravo entry unit will not be detachable once the lock is installed.

Connect one (1) battery to the battery clip. Only use 9V ALKALINE Duracell/ Procell- or

Energizer batteries.

This mounting instruction is part of VdS certification and has to be followed up

precisely.

M-LOCKS BV

Vlijtstraat 40

NL-7005 BN Doetinchem

ver. 1.1 2010 07 19

4

Tel: +31 (0)314 376 876

Fax: +31 (0)314 376 878