2024年4月6日发(作者：蓝鸿畴)
1
基本信息
（1） 问题：the board thickness(2.36+/-0.05mm) is too hard to control for us
对我们来说，板厚2.36+/-0.05mm太难管控
建议：Can we control the finished board thickness as 2.4+/-10%mm？Please
comfirm!
请确认我们可否控制完成板厚为2.4+/-10%mm？
（2） 问题：As show in figure, manufacturing requirements specification,
using 17 um (1/2 oz) based copper, finished surface copper: 46 um (0.00181 "); it is
different from what shows 1oz for stackup.
如下图所示，制作说明要求使用17um基铜，完成铜厚46um.这跟叠构中的1OZ铜
厚不符.
建议：Use 1 oz based copper, finished surface copper: 46 um (0.00181 ")
使用1oz基铜，完成铜厚46um.
（3） 问题：As show in the below figure, outer copper is 1 oz..We can’t make
sure whether the finished surface copper is 1 oz.
如下图所示，外层铜厚为1OZ，我们不能确定完成铜厚是否为1OZ.
。
1
欢迎下载
建议：Using Hoz base copper, finished surface 1 oz copper;
使用H oz基铜，成品铜厚为1oz.
（4） 问题：The stack-up your company provided did not conform the
requirements of impedance, and the inner layers need to use 3 Pre-preg.
贵司提供的叠构不符合阻抗要求，且内层需要用3张pp
建议：Adjust the thickness of the Pre-preg and the core。See below.
调整芯板和PP的厚度，见下图
（5） 问题：The make-up like as the attachment （12PCS/PNL），in order to
save the costing ,please confirm if can accept 3 X-OUT per panel?
如附件所示拼版（12pcs/PNL），为了节约成本，请确认可否接受每个拼版内有
3个打叉板？
建议：Accepted 3 X-OUT per panel,but not exceed 5% of order
pack them separately when shipping.
接受每拼版出3个打叉板，但不超过总订单数的5%，且出货时把打叉板分开
包装.
（6） 问题：As show in figure, Your company requirements according to level
。
2
欢迎下载
2024年4月6日发(作者：蓝鸿畴)
1
基本信息
（1） 问题：the board thickness(2.36+/-0.05mm) is too hard to control for us
对我们来说，板厚2.36+/-0.05mm太难管控
建议：Can we control the finished board thickness as 2.4+/-10%mm？Please
comfirm!
请确认我们可否控制完成板厚为2.4+/-10%mm？
（2） 问题：As show in figure, manufacturing requirements specification,
using 17 um (1/2 oz) based copper, finished surface copper: 46 um (0.00181 "); it is
different from what shows 1oz for stackup.
如下图所示，制作说明要求使用17um基铜，完成铜厚46um.这跟叠构中的1OZ铜
厚不符.
建议：Use 1 oz based copper, finished surface copper: 46 um (0.00181 ")
使用1oz基铜，完成铜厚46um.
（3） 问题：As show in the below figure, outer copper is 1 oz..We can’t make
sure whether the finished surface copper is 1 oz.
如下图所示，外层铜厚为1OZ，我们不能确定完成铜厚是否为1OZ.
。
1
欢迎下载
建议：Using Hoz base copper, finished surface 1 oz copper;
使用H oz基铜，成品铜厚为1oz.
（4） 问题：The stack-up your company provided did not conform the
requirements of impedance, and the inner layers need to use 3 Pre-preg.
贵司提供的叠构不符合阻抗要求，且内层需要用3张pp
建议：Adjust the thickness of the Pre-preg and the core。See below.
调整芯板和PP的厚度，见下图
（5） 问题：The make-up like as the attachment （12PCS/PNL），in order to
save the costing ,please confirm if can accept 3 X-OUT per panel?
如附件所示拼版（12pcs/PNL），为了节约成本，请确认可否接受每个拼版内有
3个打叉板？
建议：Accepted 3 X-OUT per panel,but not exceed 5% of order
pack them separately when shipping.
接受每拼版出3个打叉板，但不超过总订单数的5%，且出货时把打叉板分开
包装.
（6） 问题：As show in figure, Your company requirements according to level
。
2
欢迎下载